• 한국추진공학회지
• /
• 제17권6호
• /
• pp.11-19
• /
• 2013

본 연구에서는 고온으로 가열된 연료가 다양한 종류의 스월 인젝터를 통해 분사되는 경우 분사 특성의 변화를 실험적으로 확인하였다. 3종의 스월 인젝터로 3 ~ 10 bar의 분사압력을 가하면서 연료온도가 $50{\sim}270^{\circ}C$ 범위에서 변화하는 경우 인젝터의 유량계수(${\alpha}$)를 계측하였다. cavitation number ($K_c$)에 대한 ${\alpha}$ 변화 특성을 확인한 결과 ${\alpha}$ 변동 특성이 오리피스 직경과 스월러 형상에 모두 영향을 받았고, 비등에 의한 연료분사 특성을 스월러 유로와 오리피스 유로 면적비인 AR과 관련지어 살펴 본 결과에서는 AR이 커질수록 비등 영향은 더 지연되고 비등의 영향이 미치기 시작하면 ${\alpha}$ 감소 기울기는 더 큰 것으로 확인되었다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2005년도 제31회 KOSCO SYMPOSIUM 논문집
• /
• pp.255-260
• /
• 2005

To achieve efficient combustion within a manageable length, a successful fuel injection scheme must provide rapid mixing between the fuel and airstreams. The aim of the present numerical research is to investigate the flame holding and combustion enhancement. Additional fuel into the cavity prevents shear flow impingement on the trailing edge of the cavity. The high temperature freestream flow mixes with the cold hydrogen fuel that is injected into the cavity and raises the fuel temperature remarkably and become to start combustion. The high pressure in the cavity due to the cavity structure and combustion leads the hydrogen fuel to upstream. The shock in the cavity to be generated by the fuel injection joins together and reflects off the ceiling wall. This makes high pressure and low mach number region and makes a small recirculation in this region. This high stagnation temperature is nearly recovered in the shear layer in front of the cavity and leads to start combustion. In the downstream of the cavity, the wall pressure drops significantly. This means that the combustion phenomenon is diminished. Because fuel lumps at the trailing edge of the cavity then it spreads after the cavity so, in this region there is a strong expansion.

• International Journal of Automotive Technology
• /
• 제8권1호
• /
• pp.27-31
• /
• 2007

The number of vehicles employing diesel engines is rapidly rising. Accompanying this trend, application of an after-treatment system is strictly required as a result of reinforced exhaust regulations. The Diesel Particulate Filter (DPF) system is considered as the most efficient method to reduce particulate matter (PM), but the improvement of a regeneration performance at any engine operation point presents a considerable challenge by itself. Therefore, the present study evaluates the effect of fuel injection characteristics on regeneration performance in a DOC and a catalyzed CR-DPF system. The temperature distribution on the rear surface of the DOC and the exhaust gas emission were analyzed in accordance with fuel injection strategies and engine operating conditions. A temperature increase more than BPT of DPF system was obtained with a small amount fuel injection although the exhaust gas temperature was low and flow rate was high. This increase of temperature at the DPF inlet cause PM to oxidize completely by oxygen. In the case of multi-step injection, the abrupt temperature changes of DOC inlet didn't occur and THC slip also could not be observed. However, in the case of pulse type injection, the abrupt injection of much fuel results in the decrease of DOC inlet temperatures and the instantaneous slip of THC was observed.

• 한국분무공학회지
• /
• 제15권1호
• /
• pp.17-24
• /
• 2010

The objective of this work is to analyze the macroscopic behavior of spray and injection characteristics on the DME blended biodiesel at different mixing ratios by using spray visualization and injection rate measurement system. The spray images were analyzed to a spray tip penetration, a spray cone angle and a spray area distribution at various mixing ratio of DME by weight. The influence of different injection pressure and ambient pressure on the fuel spray characteristics are investigated for the various injection parameters. In order to analyze the injection characteristics of test fuels, the fuel injection rate is measured at various blending ratio. The variation of viscosity of the blended fuel by the mixing of DME fuel shows the improved effect of spray developments. Also, it was found that the injection quantities of high blended ratio were larger than that of lower blended fuel. Also, higher blending fuel showed a faster evaporation than that of mixing ratio of test fuel because kinetic viscosity was changed by blending ratio.

• 한국분무공학회지
• /
• 제8권4호
• /
• pp.31-38
• /
• 2003

Constant volume combustion chamber has been designed to investigate diesel spray characteristics with Common-Rail injection system to realize high pressure injection. In this study, two methods of measurements, Schlieren shadowgraphy and Mie scattering imaging method ate applied experimentally to study spray form and liquid phase zone in high pressure, high temperature conditions. Diesel fuel is injected at the point which ignited mixture gas is completely burned. The effect of injection pressure, injector hole diameter, ambient gas temperature and density are investigated experimentally.

• 한국분무공학회지
• /
• 제24권2호
• /
• pp.66-72
• /
• 2019

Diesel vehicles suffer from poor starting and running problems at cold temperatures. Diesel vehicles have the characteristic that CO and PM are reduced or similarly discharged when going from low temperature to high temperature. In this study, a bypass type piezo injector for electronic control based common rail injection system was used. Numerical analysis using injector drive analysis model was performed to analyze injector drive and internal fuel flow characteristics according to fuel temperature change. The results show that the rate of density change due to the fuel temperature is proportional, and that the effect of the kinematic viscosity is relatively large between $-20^{\circ}C$ and $0^{\circ}C$. Comparing the results of temperature condition at $0^{\circ}C$ and $20^{\circ}C$, it is considered that the viscosity is more correlated with the needle displacement than the pressure chamber of the delivery chamber.

• 한국자동차공학회논문집
• /
• 제21권5호
• /
• pp.15-24
• /
• 2013

Numerical studies were conducted to investigate the internal flow field and combustion characteristics of DISI engine with methanol blended in gasoline. Dual injection was applied and the characteristics were compared to single injection strategy. The amount of the fuel injection was corresponded to air-fuel ratio of each fuel for complete combustion. The preforming model in this study, software STAR-CD was employed for both modeling and solving. The operating speed condition were at 4000 rpm/WOT (Wide open throttle) where the engine was fully warmed. The results of single injection with M28 showed that the uniformity, equivalence ratio, in-cylinder pressure and temperature increased comparing to gasoline (M0). When dual injection was applied, there was no significant change in uniformity and equivalence ratio but the in-cylinder pressure and temperature increased. When M28 fuel and single injection was applied, the CO (Carbon monoxide) and NO (Nitrogen oxides) emission inside the combustion chamber increased approximately 36%, 9% comparing with benchmarking case in cylinder prior to TWC (Three Way Catalytic converter). When dual stage injection was applied, both CO and NO emission amount increased.

• Journal of Advanced Marine Engineering and Technology
• /
• 제35권1호
• /
• pp.53-59
• /
• 2011

디젤기관은 세계적으로 연료의 경제성 때문에 사용이 증가할 것이다. 그러나 NOx, 매연 등과 같은 배기가스를 배출한다. 본 연구는 커먼레일 연료분사 시스템에서, 연료온도, 분사 압력, 분사시간, 연료 점성에 따른 분무 특성을 실험하였다. 커먼레일 시스템에서, 디젤 연료는 분사 압력, 분사 시간에 따라 분무 형상이 다르다. 필터 압력은 연료 유동과 관련이 있는 연료 점성을 변화시키는 연료 온도에 영향을 받는다. 분무와 무화특성에 미치는 바이오 디젤 연료의 혼합율의 영향에 대해 많은 실험 조건에서 실험하였다. 바이오디젤 연료의 미립화 특성은 바이오 디젤 혼합비율이 증가하면 높은 점성 때문에 악화되는 것을 알았다.

• 한국산업융합학회 논문집
• /
• 제7권2호
• /
• pp.153-159
• /
• 2004

The purpose of this research is to investigate the performance of swirl combustion chamber diesel engine by changing the jet passage area, the depth and shape of the piston top cavity (main chamber). The performance of diesel engine with newly changed swirl combustion chamber was tested through the experimental conditions as engine speed, load and injection timing etc. The test results were compared and analyzed. And another purpose of this research is to make a new diesel engine that is satisfied fuel consumption and regulation value of exhaust gas. 1. The rate of fuel consumption was affected significantly by the jet passage area at the high speed and load than low speed and low load. The influence of jet passage large area was proven to decrease the rate of fuel consumption. 2. Smoke was affected significantly by the depth of the piston top cavity, but exhaust temperature and the rate of fuel consumption wasn't affected. The rate of fuel consumption was affected by changing injection timing. 3. The rate of fuel consumption, exhaust temperature and Smoke were affected significantly by the shape of the piston top cavity from rectangular to trapezoid. That is we have all high value. The exhaust smoke density and exhaust gas temperature depended sensitively on variation of the injection timing rather than the shape of the combustion chamber within the experimental conditions. 4. We made a new diesel engine that is satisfied design target values(sfc=190 g/hr, NOx + THC=6.0 g/KWh, PM=0.3 KWh), the rate of fuel consumption and emission standard etc., through changing injection timing at the maximum torque point and rated power point. Although we have a little high NOx value.

• 청정기술
• /
• 제13권4호
• /
• pp.300-307
• /
• 2007

본 연구에서는 연료분출각의 변화에 따라 보염기(cylindrical stabilizer) 후류에 형성되는 확산화염의 화염 안정성, 재순환영역의 길이 및 온도, 보염기 후류의 난류강도 분포, 재순환영역의 연소가스 농도 등을 측정하고, 화염의 직접사진 및 슐리렌사진을 촬영하여 확산화염의 연소특성을 고찰하였다. 화염안정성은 연료분출각과 주류공기 유속의 영향을 받으며, 재순환영역의 길이와 온도는 연료분출각의 영향을 받았다. 재순환영역의 길이가 짧고 온도가 낮을수록 화염안정성이 양호하지만, 연료분출각의 변화에 따른 난류강도 분포에는 별로 차이가 없었다. 재순환영역 내 미연가스 농도가 높고 이산화탄소 농도가 낮은 경우, 화염안정성은 양호하지만 연소상태는 불량한 것으로 나타났다. 연소효율, 고부하 출력, 대기환경, 연료의 청정연소조건 등을 고려하여 적절한 연료분출각을 선정함으로써 양호한 연소조건을 유지할 수 있다.