본 연구의 목적은 한랭지역에서 운영 중인 터널구조물의 누수를 유도배수하기 위하여 기존 유도배수시스템을 향상시키는 것이다. 유도배수시스템은 유도배수판, 방수재료인 Hotty-gel, Hotty-gel 돌출 방지판, 공압타카, 고정핀, 집수관, 유도배수관, 철망 및 뿜어 붙임 모르타르로 구성되어 있다. 유도배수시스템은 현장 적용성 및 시공성을 평가하기 위하여 재래식 콘크리트 라이닝 터널에서 시험 시공되었다. 재령 7일, 14일, 21일, 28일, 2개월, 3개월, 4개월, 5개월, 6개월, 7개월 및 8개월에 약 1,000 ml의 붉은색 물을 유도배수시스템 배면에 주입하여 유도배수시스템의 방수과 유도배수 성능을 평가하였다. 현장 성능 평가 실험이 진행된 8개월 동안 터널이 위치한 지역의 일일 평균 온도는 $-16.0~25.6^{\circ}C$로 측정되었고, 일일 최저 온도는 $-21.3^{\circ}C$, 일일 최고 온도는 $30.8^{\circ}C$였다. 유도배수시스템의 유도배수판에서는 누수가 발생하지 않았지만 재령 14일부터 유도배수관에서 누수가 발생하였다. 유도배수관 누수는 고압의 공압타카와 고정핀 사용으로 두께 0.2 cm인 연성플라스틱 재질의 유도배수관이 변형되었고, 누수 방지를 위한 Hotty-gel의 두께와 폭이 충분하지 않아서 발생한 것으로 판단된다.
본 논문에서는 200 kW급 마이크로 가스 터빈 시스템의 연소기집합체의 열-구조 연성 해석을 수행하였다. 일반적인 연소기집합체는 라이너, 내외 케이스, 버너와 노즐링 등으로 구성되어 있으며, 본 연구에서 개발된 유한요소모델은 연소기집합체 내 다양한 부품들의 다른 열팽창을 보상하기 위해 부품간의 이격과 마찰 요소들이 존재하므로 비선형 간극 및 마찰 요소 등을 포함하고 있다. 본 연구를 통해 연소기집합체의 외부 경계지지조건이 높은 온도구배로 인한 응력 에 가장 큰 영향을 주는 인자라는 것을 밝혀냈으며, 과도한 응력이나 변형을 방지하기 위한 적절한 외부 경계지지조건을 찾기 위하여 외부 경계지역에 탄성 지지조건을 가상하여 적절한 경계조건을 도출하여 설계에 사용될 수 있도록 하였다.
Microstructural evolution in the thickness direction of an oxygen free copper processed by accumulative rollbonding (ARB) is investigated by electron back scatter diffraction (EBSD) measurement. For the ARB, two copper alloy sheets 1 mm thick, 30 mm wide and 300 mm long are first degreased and wire-brushed for sound bonding. The sheets are then stacked and roll-bonded by about 50% reduction rolling without lubrication at an ambient temperature. The bonded sheet is then cut to the two pieces of the same dimensions and the same procedure was repeated on the sheets up to eight cycles. The specimen after 1 cycle showed inhomogeneous microstructure in the thickness direction so that the grains near the surface were finer than those near the center. This inhomogeneity decreased with an increasing number of ARB cycles, and the grain sizes of the specimens after 3 cycles were almost identical. In addition, the aspect ratio of the grains decreased with an increasing number of ARB cycles due to the subdivision of the grains by shear deformation. The fraction of grains with high angle grain boundaries also increased with continuing process of the ARB so that it was higher than that of the low angle grain boundaries in specimens after 3 cycles. A discontinuous dynamic recrystallization occurred partially in specimens after 5 cycles.
본 연구에서는 탄소섬유 강화 복합재의 점탄성 성질을 적용한 유한요소 해석에 대해서 기술하였다. 고온의 성형과정에서 발생하는 가장 중요한 문제 중 하나는 잔류응력의 발생이다. 잔류응력으로 인해 성형이 끝난 후 뒤틀림, 균열이 일어 날 수 있으며 이는 완성품에 심각한 결함을 가져올 수 있다. 잔류응력의 주요 원인은 점탄성이며 고온의 성형과정에서 열팽창계수의 차이와 수지의 시간 및 온도에 대한 물성의 변화로 인해 발생하는 탄소섬유 강화 복합재의 특징이다. 화학 수축도 잔류응력에 많은 영향을 주며 이를 고려한 뒤틀림 예측에서 오차를 줄일 수 있는 중요한 요소이다. 본 연구는 복합재 성형에 사용된 온도변화에 대한 경화도와 점탄성 효과, 화학수축을 유한요소 해석으로 수행하기 위한 기법을 연구하고, 점탄성의 영향성을 연구하였다. 기존에 연구되어 있는 논문을 참고하여 서브루틴의 타당성을 검증한 후 나아가 복합재의 적층각의 변화에 따른 응력과 변형을 해석해 봄으로써 실제 복합재의 성형 시 발생하는 휨 현상에 대한 예측방법을 제시하였다.
본 논문에서는 네트워크 서버용 컴퓨터 주기판 내 장착된 열방열 시스템 지지구조물에 대한 유한요소 모델의 솔더 크리프 특성을 검증하였다. 열방열 시스템은 앵커 구조물로 지지되며 앵커 구조물은 솔더를 이용하여 인쇄회로기판에 장착된다. 컴퓨터 내 발생하는 지속적인 고온환경 하에서 솔더의 크리핑이 발생하고 이는 궁극적으로 지지구조물의 파괴로 이어진다. 유한요소모델은 솔더에 발생하는 응력분석과 수명예측을 위해 사용되며, 솔더 크리프 특성을 모사하기 위하여 Anand 크리프 모델을 적용하였다. 모델을 검증하고 교정하기 위하여 크리프 시험을 수행하였다. 시험은 인쇄회로기판의 변형을 제외한 솔더 변형만을 측정하기 위하여 특별한 지그를 설계하여 수행하였다. 크리프 시험결과를 유한요소해석결과와 비교하여 Anand 크리프 모델을 검증하고 교정을 수행하였다. 교정된 유한요소모델을 이용하여 열방열 시스템 구조물의 보다 정확한 수명 예측을 수행할 수 있다.
ABS 수지의 파단 거동을 살펴 보기 위해 rubber content, molecular weight, lubricant의 종류 및 양과 파단 speed, 주위 환경온도를 변수로 측정한 후 전자현미경 사진으로 그 파단면을 살펴 보았다. Tension하에서 rubber content와 lubricant content는 감소할수록, molecular weight와 tension speed는 증가할수록 strength는 증가하였으며, 파단면은 rubber content, speed, molecular weight는 감소할수록, liquid lubricant를 사용할수록 파단부위 주변의 변형이 일어나지 않았으며, 파단면도 수지가 서로 미끄러져 파단되는 상태가 아닌 상분리와 같은 형상으로 분리파단되었다. Impact하에서 rubber content, molecular weight, 주위 환경온도, lubricant content가 증가할수록 strength도 증가하였으며, 파단면은 사진상의 파단표면적이 작은 것이 높은 strength를 나타내고 있다.
마그네슘 합금은 비중이 1.74로 가벼운데다 비강도는 구조용 금속 중에서 가장 크며, 방진성, 전자파 차폐성, 저용점 용 여러 가지 장점이 있어 최근 자동차 부품과 전자산업 제품 분야에서 이용이 크게 기대되는 금속이다. 그러나 마그네슘의 결정구조는 조밀 육방정이기 때문에 소성변형이 가능한 슬립면이 한정되어 있으며 압연이나 압출가공 시에는 강한 집합조직이 형성되어 상온가공이 곤란하다. 따라서 지금까지 성형성 개선을 위한 조직제어와 성형기술 분야에서 많은 연구개발이 이루어져 왔다. 본고에서는 결정립과 집합조직에 관한 미세조직의 제어방법, 용체성형, 압연 및 압출에 관한 성형가공 기술과 마그네슘 스크랩 리싸이클링 기술에 관하여 최근의 연구개발 사례를 소개한다.
The pressure tubes made of cold-worked Zr-2.5Nb alloy are subjected to creep deformation during service period resulting in changes to their geometry such as longitudinal elongation, diameter increase and sagging. To evaluate integrity of them, information on the material creep property of the serviced tubes is essential. As one of the methods with which the creep property is directly measured from the serviced components, small punch(SP) creep testing has been considered as a substitute for the conventional uniaxial creep testing. In this study, applicability of the SP creep testing to Zr-2.5Nb pressure tube alloy was studied particularly by measuring the power law creep constants, A, n. The SP creep test has been successfully applied fur other high temperature materials which have isotropic behavior. Since the Zr-2.5Nb alloy has anisotropic property, applicability of the SP creep testing can be limited. Uniaxial creep tests and small punch creep tests were conducted with Zr-2.5Nb pressure tube alloy along with finite element analyses. Creep constants obtained by each test method are compared. It was argued that the SP creep test result gave results reflecting material properties of both directions. But the equations derived in the previous study for isotropic materials need to be modified. Discussions were made fur future research directions for application of the SP creep testing to Zr-2.5Nb tube alloy.
In this study the new creep test using miniaturized specimen(10${\times}$10${\times}$0.5 ㎣) was performed to evaluate the creep characteristics for degraded materials of 2.25Cr-1Mo steel. For this creep test, the artificially aged materials for 330 hrs and 1820hrs at $630^{\circ}C$ were used. The test temperatures applied for the creep deformation of miniaturized specimens was X$630^{\circ}C$ and the applied loads were between 45 kg∼80 kg. After creep test, macro- and microscopic observation were conducted by the scanning electron microscope(SEM). The creep curves depended definitely on applied load and microstructure and showed the three stages of creep behavior like uniaxial tensile creep curves. The load exponents of virgin, 330 hrs and 1820 hrs materials based on creep rate showed 14.8, 9.5 and 8.3 at $550^{\circ}C$ respectively, The 1820 hrs material showed the lowest load exponent and this behavior was also observed in the case of load exponent based on creep rupture time. In contrast to virgin material which exhibited fined dimple fractography, a lot of carbides like net structure and voids were observed on the fractography of degraded materials.
대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
/
pp.661-667
/
2002
Welding-induced buckling distortion is one of the most problematic concerns in both design and fabrication of welded thin-plate structures. This paper deals with experimental and numerical results of the welding-induced longitudinal and/or buckling distortion occurring in welding of 6mm-thick AH36 high strength steel plates. Effects of the heat input and the plate size on the distortion were experimentally evaluated for square plates. Bead-on-plate welding was performed with the submerged arc welding process along the middle line of plate specimens. Experimental results showed that the longitudinal distortion made a single curvature in the plate, and the distortion magnitude along the weld centerline was proportional to the heat input and the plate size. The experimental results were used to examine the validity of the numerical simulation procedure for welding-induced distortion where the longitudinal distortion mode and magnitude were numerically quantified. Three-dimensional, large deformation, welding simulations were performed for selected weld models. Numerical results of the distortion mode and magnitude were in a good agreement with experimental ones. Depending on the presence of halting the distortion growth during the cooling cycle of welding, the condition discriminating buckling distortion from longitudinal distortion was established. Eigenvalue analyses were performed to check the buckling instability of tested plates with different sizes subjected to different heat inputs. The perturbation load pattern for the analysis was extracted from longitudinal inherent strain distributions. Critical buckling curve from the eigenvalue analyses revealed that the buckling instability is manifested when plate size or heat input increases.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.