• Microbiology and Biotechnology Letters
• /
• v.19 no.4
• /
• pp.343-347
• /
• 1991

An improved method for the selection of high tobramycin-producing mutants of Streptomyces tenebrarius ATCC 17920 was investigated. By the use of apramycin-containing media, low nebramycin-producing mutants were eliminated. Strain No. 23, resistant to apramycin and kanamycin B and sensitive to tobramycin, was isolated from soils, identified as Pseudomonas paucimobilis and used as a test organism for overlaying the mutants on agar plate. While inhibition zones were not shown when the parent strains were overlaid with soft agar containing the strain No. 23, clear zones were shown when high tobramycin-producing mutants were overlaid. Using this screening strategy, 58 mutants showing clear zones had been isolated. antibiotic activities of which were incresed to 3~8 fold compared to that of parent strain.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.423-426
• /
• 2001

Recently we have reported that the meander-patterned amorphous FeCoSiB films exhibit large change in their high frequency impedance by applying a strain, suggesting that the films are very attractive for making of a highly sensitive strain sensor elements. In this study, the effect of anisotropy on a change in the impedance of sputtered amorphous film patterns was investigated in the frequency range from 1MHz to 1GHz. As a function of applied strains, the high frequency impedance was extremely changed in the case of film patterns with transverse anisotropy due to excellent magnetomechanical coupling properties. As a summary, the maximum figure of merit f has measured about 2600 in the case of transverse anisotropy, and about 500 in the case of longitudinal anisotropy at 500 MHz. These values of F are approximately more than 1000 times higher than that of a conventional metal strain gauge (F 2) and more than 10 times higher than that of a semiconductor gauge (F 200).

• Journal of the Korean Ceramic Society
• /
• v.47 no.6
• /
• pp.491-497
• /
• 2010

In this paper, we employed the classical molecular dynamics simulations using Tersoff's potential to calculate the elastic constants of the silicon carbide (SiC) crystal at high temperature. The elastic constants of the SiC crystal were calculated based on the stress-strain characteristics, which were drawn by the simulation using LAMMPS software. At the same time, the elastic constants of the SiC ceramics were measured at different temperatures by impulse excitation testing (IET) method. Based on the simulated stress-strain results, the SiC crystal showed the elastic deformation characteristics at the low temperature region, while a slight plastic deformation behavior was observed at high strain over $1,000^{\circ}C$ temperature. The elastic constants of the SiC crystal were changed from about 475 GPa to 425 GPa by increasing the temperature from RT to $1,250^{\circ}C$. When compared to the experimental values of the SiC ceramics, the simulation results, which are unable to obtain by experiments, are found to be very useful to predict the stress-strain behaviors and the elastic constant of the ceramics at high temperature.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.9
• /
• pp.1174-1184
• /
• 1997

Extinction characteristics of pure hydrogen-oxygen diffusion flames, at high pressures in the neighborhood of the critical pressure of oxygen, is numerically studied by employing counterflow diffusion flame as a model flame let in turbulent flames in rocket engines. The numerical results show that extinction strain rate increases almost linearly with pressure up to 100 atm, which can be explained by comparison of the chain-branching-reaction rate with the recombination-reaction rate. Since contributions of the chain-branching reactions, two-body reactions, are found to be much greater than those of the recombination reactions, three-body reactions, extinction is controlled by two-body reactions, thereby resulting in the linearity of extinction strain rate to pressure. Therefore, it is found that the chemical kinetic behaviors don't change up to 100 atm. Consideration of the pressure fall-off reactions shows a slight increase in extinction strain rate, but does not modify its linearity to pressure. The reduced kinetic mechanisms, which were verified at low pressures, are found to be still valid at high pressures and show good qualitative agreement in prediction of extinction strain rates. Effect of real gas is negligible on chemical kinetic behaviors of the flames.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.23 no.1
• /
• pp.175-178
• /
• 2011

Yeonnokjam is a newly bred high yield special silkworm strain for spring rearing, bred from Japanese originated green cocoon spinning strain Jam 315 and Chinese originated white cocoon spinning strain Jam 316. This strain showed high hatching ratio of 96% and high healthiness of 96.7% of pupatin ratio. And its spins heavier cocoon with somewhat shorter fiber length but thicker fineness. The merits of these_strains are short larval period and labor saving, and its breeding goals are producing polish green silk and use for education.

• Transactions of Materials Processing
• /
• v.3 no.4
• /
• pp.427-439
• /
• 1994

The high temperature deformation behavior of $SiC_p/Al-Si$ composites and Al-Si matrix was studied by hot torsion test in a range of temperature from $270^{\circ}C$ to $520^{\circ}C$ and at strain rate range of $1.2{\times}10_{-3}~2.16{\times}10_{-1}/sec$. The hot restoration mechanisms for both matrix and composites were found to be dynamic recrystallization(DRX) from the investigation of flow curves and microstructural evolutions. The Si precipitates and SiC particles promoted DRX, and the peak strain$({\varepsilon}_p)$ of the composites was smaller than that of the matrix. Flow stresses of $SiC_p/Al-Si$ composites were found to be generally higher than the matrix, but the difference was quite small at higher temperature due to the decrease of capability of load transfer by SiC particles. With increasing temperature, failure strain of matrix and composites are inclined to increase, the increasing value of failure strain for the $SiC_p/Al-Si$ composites was small compared to that of matrix. The stress dependence of both materials on strain rate() and temperature(T) was examined by hyperbolic sine law, $\.{\varepsilon}=A_1[sinh({\alpha}{\cdot}{\sigma})]_n$exp(-Q/RT)

• Journal of the Korean Society for Heat Treatment
• /
• v.37 no.2
• /
• pp.66-72
• /
• 2024

To investigate the effect of deformation condition on microstructure and texture formation behaviors of AZ91 magnesium alloy with three kinds of initial texure during high-temperature deformation, plane strain compression tests were carried out at high-temperature deformation conditions - temperature of 673 K~723 K, strain rate of 5 × 10^-3s^-1, up to a strain of -1.0. To clarify the texture formation behavior and crystal orientaion distribution, X-ray diffraction and EBSD measurement were conducted on mid-plane section of the specimens after electroltytic polishing. As a result of this study, it is found that the main component and the accumulation of pole density vary depending on initial texture and deformation caondition, and the formation and development basal texture components ({0001} <$10\bar{1}0$>) were observed regardless of the initial texure in all case of specimens.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.27 no.3
• /
• pp.147-154
• /
• 2014

In the context of an increasing need for safety in concrete structures under blast and impact loading condition, the behavior of concrete under high strain rate condition has been an important issue. Since concrete subjected to impact loading associated with high strain rate shows quite different material behavior from that in the static state, several material models are proposed and used to describe the high strain rate behavior under blast and impact loading. In the process of modelling high strain rate conditions with these material models, mesh dependency in the used finite element(FE) is the key problem because simulation results under high strain-rate condition are quite sensitive to applied FE mesh size. This paper introduces an criterion which can minimize the mesh-dependency of simulation results on the basis of the fracture energy concept, and HJC(Holmquist Johnson Cook) model is examined to trace sensitivity to the used FE mesh size. To coincide with the purpose of the perforation simulation with a concrete plate under a projectile(bullet), the residual velocities of projectile after perforation are compared. The analytical results show that the variation of residual velocity with the used FE mesh size is quite reduced and accuracy of simulation results are improved by applying a unique failure strain value determined according to the proposed criterion.

• Journal of Species Research
• /
• v.10 no.4
• /
• pp.336-343
• /
• 2021

In 2020, as a subset study to discover indigenous yeast species in Korea, a total of 22 yeast species were isolated from soil samples collected in Gwangju-si, Gyeonggi-do. Among them, 10 strains were unreported species. From the high 26S rRNA gene sequence similarity and formation of a robust phylogenetic clade with the closest species, it was determined that each strain belonged independent and predefined yeast species. The 22 strains were assigned to the genera Dothiora (1 strain), Sarocladium (1 strain), Tetrapisispora (1 strain) and Torulaspora (2 strains) of the phylum Ascomycota; the genera Erythrobasidium (1 strain), Leucosporidium (4 strains), Ustilentyloma (2 strains), Fellozyma (1 strain), Sampaiozyma (2 strains), Filobasidium (1 strain), Solicoccozyma (2 strains) and Vishniacozyma (4 strains) of the phylum Basidiomycota. This is the first official report of the following species in Korea: Dothiora cannabinae (1 strain), Sarocladium strictum (1 strain), Fellozyma inositophila (1 strain), Filobasidium magnum (1 strain), Solicoccozyma phenolicus (1 strain), Solicoccozyma terreus(1 strain), Vishniacozyma tephrensis(1 strain) and Vishniacozyma victoriae (3 strains). Cell morphology, phenotypic features and biochemical features are described in the Species Description section.

• Magazine of the Korea Concrete Institute
• /
• v.11 no.2
• /
• pp.197-208
• /
• 1999

The use of high-strength concrete which permits smaller cross sections, reduced dead loads, and longer spans has been getting more popular in tall buildings. However, there has been little research on behavior of high-strength concrete columns laterally reinforced with square ties and subjected to compressive loading. With the addition of transverse reinforcement which lead to triaxial compressive state, ductility behavior of high-strength column member shall be increased. In this study, rational quality and quantity evaluations were made to investigate the ultimate strength and strain ductility by confinement effect of tie reinforced high-strength concrete columns subject to uniaxial loads. Concrete failure theory at the triaxial compressive state and statistical results based on conventional experimental data were applied for this propose. Up to 185 columns, tested under monotonically increasing concentric loading, were evaluated in terms of strength and strain ductility. Analytical results show that confinement stress, maximum compressive strength, and increase of strain equations were developed with the consideration of concrete strength, yield strength, spacing, volumetric ratio, and configurations of tie reinforcement.