• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.6
• /
• pp.440-448
• /
• 2009

Facility power-line electromagnetic interference (EMI) filters are used to provide radio frequency(RF) isolation between dedicated power distribution services and noise sensitive local power distribution systems. This type of EMI filters generally needs a high current capacity and, in some special applications, a high insertion loss of a minimum 100dB from 14kHz through 10GHz per MIL-STD 220 is required. This paper deals with an analysis and design of a wideband facility power-line EMI filter with the above requirements. The characteristics of the inductor and capacitor at high frequencies are investigated. The characteristics and design method of the facility EMI filter with a high order LC network are also presented. The prototype filter is finally implemented and its performance is verified from the experimental results.

• Journal of electromagnetic engineering and science
• /
• v.6 no.4
• /
• pp.217-221
• /
• 2006

Multipactor-free S-band duplexer based on inter-digital cavity type filter is proposed and demonstrated by in-house mulitpactor test facility for satellite RF components. Multipactor sensitivity of designed duplexer is analyzed by checking it out the maximum field accumulated region inside duplexer and calculating the electric field intensities at each resonator using 3D EM simulation in order to restrict the minimum gap distance as 2.5 mm which handles 43.13 dBm RF input power. Multipactor threshold was finally detected at 44 dBm in experiment for pulse mode test. The developed multipactor test method is cost effective, simple structure and gives a good agreement compared with the previous high cost MP test methodologies.

• ETRI Journal
• /
• v.42 no.5
• /
• pp.781-789
• /
• 2020

In this study, an E-band low-noise amplifier (LNA) monolithic microwave integrated circuit (MMIC) has been designed using silicon-germanium 130-nm bipolar complementary metal-oxide-semiconductor technology to suppress unwanted signal gain outside operating frequencies and improve the signal gain and noise figures at operating frequencies. The proposed impedance-controllable filter has series (R_s) and parallel (R_p) resistors instead of a conventional inductor-capacitor (L-C) filter without any resistor in an interstage matching circuit. Using the impedance-controllable filter instead of the conventional L-C filter, the unwanted high signal gains of the designed E-band LNA at frequencies of 54 GHz to 57 GHz are suppressed by 8 dB to 12 dB from 24 dB to 26 dB to 12 dB to 18 dB. The small-signal gain S₂₁ at the operating frequencies of 70 GHz to 95 GHz are only decreased by 1.4 dB to 2.4 dB from 21.6 dB to 25.4 dB to 19.2 dB to 24.0 dB. The fabricated E-band LNA MMIC with the proposed filter has a measured S₂₁ of 16 dB to 21 dB, input matching (S₁₁) of -14 dB to -5 dB, and output matching (S₂₂) of -19 dB to -4 dB at E-band operating frequencies of 70 GHz to 95 GHz.

• Journal of Advanced Navigation Technology
• /
• v.20 no.6
• /
• pp.556-561
• /
• 2016

This paper describes implementation of a 13.56 MHz, 5 kW RF high power generator for ISM band applications. This RF generator consists of four LDMOS modules of 1.25kW class-AB push-pull power amplifier with drive amplifier and its outputs are combined by using Wilkinson type transmission-line transformers. Its generator has a high efficiency and output power better than linearity. In order to discharge power transistor heats, we used on water cooled copper plate. Also, these have a composite circuit of combiner and low-pass filter and safety circuit to detector over and reflected power. The RF generator has achieved a efficiency of 79 % at 5.33 kW of saturated power level experimentally.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.4
• /
• pp.443-451
• /
• 2010

This paper describes a fully integrated CMOS low-IF mobile-TV RF tuner for Band-III T-DMB/DAB applications. All functional blocks such as low noise amplifier, mixers, variable gain amplifiers, channel filter, phase locked loop, voltage controlled oscillator and PLL loop filter are integrated. The gain of LNA can be controlled from -10 dB to +15 dB with 4-step resolutions. This provides a high signal-to-noise ratio and high linearity performance at a certain power level of RF input because LNA has a small gain variance. For further improving the linearity and noise performance we have proposed the RF VGA exploiting Schmoock's technique and the mixer with current bleeding, which injects directly the charges to the transconductance stage. The chip is fabricated in a 0.18 um mixed signal CMOS process. The measured gain range of the receiver is -25~+88 dB, the overall noise figure(NF) is 4.02~5.13 dB over the whole T-DMB band of 174~240 MHz, and the measured IIP3 is +2.3 dBm at low gain mode. The tuner rejects the image signal over maximum 63.4 dB. The power consumption is 54 mW at 1.8 V supply voltage. The chip area is $3.0{\times}2.5mm^2$.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.8 no.6
• /
• pp.64-72
• /
• 2009

In this paper, a high efficiency 2.45 GHz rectenna with a microstrip patch antenna and a dual-mode band-pass filter in which the 2nd and 3rd harmonics are suppressed, is presented. From the experimental results, the 2.45GHz rectenna using 3rd harmonic suppressed dual-mode BPF shows the conversion efficiency of 41.6% with incident power density of 0.3 mW/cm2 and the received power of 1.66 mW. This result shows high conversion efficiency because the received power of this rectenna is lower than other rectennas to be compared with. This rectenna can be applied to the WPT (Wireless Power Transmission) field for energy harvesting. Also, it is expected to be used to provide the stand-by power for the low power devices for USN, and wireless power transfer in sensor application of MEMS devices.

• The Journal of the Korea Contents Association
• /
• v.6 no.4
• /
• pp.1-10
• /
• 2006

In this paper, a broadband RF module is designed and tested for 2.4GHz band applications. The RF module is composed of a low noise amplifier (LNA) with a three stage amplifier, a single ended gate mixer, matching circuits, a hairpin line band pass filter and a Chebyshev low pass filter to convert the radio frequency (RF) into the intermediate frequency (IF). The LNA has a high gain and stability, and the single ended gate mixer has a high conversion gain and wide dynamic range. In the analysis of the broadband RF module, the composite harmonic balance technique is used to analyze the operating characteristics of an RF module circuit. The RF module has a 55.2dB conversion gain with a 1.54dB low noise figure, $-120{\sim}-60dBm$ wide RF power dynamic range, -60dBm low harmonic spectrum and a good isolation factor among the RF, IF, and local oscillator (LO) ports.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.9
• /
• pp.825-833
• /
• 2016

This paper introduces a direct-conversion CMOS RF transmitter for the IEEE 802.15.4 standard with a low-power high-gain up-conversion mixer designed in $0.18{\mu}m$ process. The designed RF DCT(Direct Conversion Transmitter) is composed of differential DAC(Digital to Analog Converter), passive low-pass filter, quadrature active mixer and drive amplifier. The most important characteristic in designing RF DCT is to satisfy the 2.4 GHz Zigbee standard in low power. The quadrature active mixer inside the proposed RF DCT provides enough high gain as well as sufficient linearity using a gain boosting technique. The measurement results for the proposed transmitter show very low power consumption of 7.8 mA, output power more than 0 dBm and ACPR (Adjacent Channel Power Ratio) of -30 dBc.

• Journal of electromagnetic engineering and science
• /
• v.8 no.3
• /
• pp.119-128
• /
• 2008

In this paper, we propose a developing approach of 600 W super high frequency(SHF) traveling wave tube amplifier (TWTA) for communications. Also, we make a TWTA called the experimental-TWTA(ETWTA), which uses a cathode ripple reduction technique to improve RF performance. After implementation, we discuss, and compare it with some other TWTAs. Its RF performance is better than that of other TWTAs. Therefore, this methodology can be used to develop the high power SHF TWTA for communications.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.11
• /
• pp.978-984
• /
• 2015

In this paper, we designed a RF transceiver operating up to 200 km operating range and 45 Mbps data rate. The RF transceiver operates in Ku band and composed of up/down converter, high power amplifier, front-end elements. To satisfy the operating range of RF transceiver, 10W power amplifier was required and realized by using GaN power amplifier. Moreover, to mitigate mutual interference for different bandwidth signals due to the adaptive transmission speed control function, SAW filter bank structure was used. To verify system requirement satisfaction AWR simulation tool was used.