• Korean Journal of Materials Research
• /
• v.33 no.4
• /
• pp.159-163
• /
• 2023

Zinc-ion Batteries (ZIBs) are currently considered to be effective energy storage devices for wearable electronics because of their low cost and high safety. Indeed, ZIBs show high power density and safety compared with conventional lithium ion batteries (LIBs) and exhibit high energy density in comparison with supercapacitors (SCs). However, in spite of their advantages, further current collector development is needed to enhance the electrochemical performance of ZIBs. To design the optimized current collector for high performance ZIBs, a high quality graphene film is suggested here, with improved electrical conductivity by controlling the defects in the graphene film. The graphene film showed improved electrical conductivity and good electron transfer between the current collector and active material, which led to a high specific capacity of 346.3 mAh g^-1 at a current density of 100 mA g^-1, a high-rate performance with 116.3 mAh g^-1 at a current density of 2,000 mA g^-1, and good cycling stability (68.0 % after 100 cycles at a current density of 1,000 mA g^-1). The improved electrochemical performance is firmly because of the defects-controlled graphene film, leading to improved electrical conductivity and thus more efficient electron transfer between the current collector and active material.

• Journal of the Korean Electrochemical Society
• /
• v.6 no.3
• /
• pp.174-177
• /
• 2003

Electric double-layer capacitors based on charge storage at the interface between a high surface area activated carbon electrode and an electrolyte solution are characterized by their long cycle-life and high power density in comparison with batteries. However, energy density of electric double-layer capacitors obtained at present is about 6 Wh/kg at a power density of 500W/kg which is smaller as compared with that of batteries and limits the wide spread use of the capacitors. Therefore, a new capacitor that shows larger energy density than that of electric double-layer capacitors is proposed. The new capacitor is the hybrid capacitor consisting of activated carbon cathode, carbonaceous anode and an organic electrolyte. Maximum voltage applicable to the cell is over 4.2V that is larger than that of the electric double-layer capacitor. As a result, discharged energy density on the basis of stacked volume of electrode, current collector and separator is more than 18Wh/l at a power density of 500W/l.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.16 no.6
• /
• pp.587-593
• /
• 2011

A new high power density and low cost Photovoltaic Power Conditioning System (PV PCS) with energy storage system is proposed. Its high power density and cost effectiveness can be achieved through the unification of the maximum power point tracker and battery charger/discharger. Despite of the reduced power stage, the proposed system can achieve the same performances of maximum power point tracking and battery charging/discharging as the conventional system. Moreover, the high voltage stress across the link-capacitor can be relieved through the series-connected link-capacitor with the battery. Therefore, a large number of series/parallel-connected link-capacitors can be reduced by 4-times. Especially, when the utility power failure happens, both photovoltaic and battery energies can be supplied to the load with only one power stage. Therefore, it features a simpler structure, less mass, lower cost, and fewer devices. Finally, to confirm the operation, validity, and features of the proposed system, theoretical analysis and experimental results from a single phase AC 220Vrms/1.5kW prototype are presented.

• Proceedings of the KIEE Conference
• /
• 1997.07f
• /
• pp.1924-1926
• /
• 1997

With the development of power electronics, many new energy storage systems such as the superconducting magnetic energy storage, the flywheel energy storage, and the capacitive energy storage, etc. are being intensively studied recently in order to replace battery in some special applications, Among these innovative energy storage systems, the flywheel system exhibits some unique features such as high power density, easy maintenance and longer lifetime. This paper introduces the novel flywheel energy storage system. Operation and features of the system are illustrated and verified on a 6kVA, 20kHz IPM based experimental circuit for O/A application. The Halbach Array Motor is selected of the design of the three phase motor/generator for the flywheel energy storage system.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.7
• /
• pp.417-427
• /
• 2014

Renewable energy sources such as solar, wind and hydro provides utilizing renewable power and reduce the using fossil fuels. On the other hand, it is too critical to apply power system due to the intermittent nature of renewable energy sources, the continuous fluctuations of the power load, and the storage with high energy density. Energy storage system, including pumped-hydroelectric energy storage, compressed-air energy storage, superconducting magnetic energy storage, and electrochemical devices like batteries, supercapacitors and others have shown that solve some of the challenges. In this paper, we review the current state of applications of energy storage systems, and atomic layer deposition technology, graphene materials on the energy storage systems and processes.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1521-1527
• /
• 2000

A micromirror actuated by piezoelectric unimorph cantilevers is proposed as a tine-tracking device for high-density optical data storage. Bending motions of the metal/PZT/metal unimorphs translate an integrated micromirror along the out-of-plane vertical direction. The micromirror alters the optical path of the incident laser beam and linearly steers the reflected laser beam by its out-of-plane parallel actuation. Numerical analysis shows that the actuated micromirror can satisfy the tracking speed imposed by the requirement on the access time for the high-density optical data storage up to few tens Gbitlin2 owing to the light mass of the micromirror. In this paper, preliminary characteristics of the micro-machined PZT actuated micromirror (PAM) are reported. Only a 360 nm-thick PZT film deposited by sol-gel process shows both good electrical and mechanical characteristics for the fine-tracking actuator. The micromirror can be easily actuated up to several micrometers under low voltage operation condition well below 10 volts.

• Transactions of the Society of Information Storage Systems
• /
• v.1 no.2
• /
• pp.192-196
• /
• 2005

In this paper, we investigated the possibility of replicating patterned media by nano-injection molding process with a metallic nano-stamper. The original nano-master was fabricated by E-beam lithography and ICP etching process. The metallic nano-stamper was fabricated using a nanoimprint lithography and nano-electroforming process. The nano-patterned substrate was replicated using a nano-injection molding process without additional etching process. In nano-injection molding process, since the solidified layer, generated during the polymer filling, deteriorates transcribability of nano patterns by preventing the polymer melt from filling the nano cavities, an injection-mold system was constructed to actively control the stamper surface temperature using MEMS heater and sensors. The replicated polymeric patterns using nano-injection molding process were as small as 50 nm in diameter, 150 nm in pitch, and 50 nm in depth. The replicated polymeric patterns can be applied to high density patterned media.

• Proceedings of the Korean Magnestics Society Conference
• /
• 1994.03a
• /
• pp.12-13
• /
• 1994

Magnetic recording is still considered to be a.leader in storage industries in general. The rigid disk drive, in particular, has an advantage over tape, optical, magneto-optical, or flash memories, because of high areal density and fast access time with reasonably low cost per Mbyte. However, to be competitive in the market and to keep an edge over other storage devices, head and media in rigid disk drives require better performance per cost and more aggressive improvement in areal density, as shown in Fig. 1, than before. In this review paper, the future trend in head/media technologies of the rigid disk drive has been reviewed. Thin film media and thin film inductive/MR heads will be mainly discussed, since they are expected to be dominant in the future high-end drives over other technologies, such as particulate media or MIG heads.(omitted)mitted)

• Journal of the Korean Magnetics Society
• /
• v.8 no.2
• /
• pp.99-110
• /
• 1998

MR head technology from the perspective of read sensor evolution was reviewed. AMR sensors have been developed for last two decades and successfully employed into information storage devices such as disk drives. Development of manufacturable GMR sensors is of emerging technological interest because GMR sensors can further meet the need of ultrahigh recording density. In this review, the mechanisms, materials systems, operating principles of both AMR an GMR sensors, and the head structures were discuseed. Constructing GMR heads with ultrathin sensor materials and complex topographical structures demands unique fabrication and design challenges. The commercialization of GMR heads can only be realized by the succesful implementations of high performance materials, advanced thin film processes, and stable head design.

• Proceedings of the SAREK Conference
• /
• 2008.11a
• /
• pp.487-492
• /
• 2008

The cooling of data centers has emerged as a significant challenge as the density of IT server increases. Server installations, along with the shrinking physical size of servers and storage systems, has resulted in high power density and high heat density. The introduction of high density enclosures into a data center creates the potential for "hot spots" within the room that the cooling system may not be able to address, since traditional designs assume relatively uniform cooling patterns within a data center. The cooling system for data center consists of a CRAC or CRAH unit and the associated air distribution system. It is the configuration of the distribution system that primarily distinguishes the different types of data center cooling systems, this is the main subject of this paper.