• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.6
• /
• pp.594-602
• /
• 2022

Cast-resin transformers are widely installed in various electrical power systems because of their low operating cost and low influence on external environmental factors. However, when they have an internal defect during the manufacturing process or operation, a partial discharge (PD) occurs, and eventually destroys the insulation. In this paper, a Rogowski-type PD sensor was studied to replace commercial PD sensors used for the insulation diagnosis of power apparatus. The proposed PD sensor was manufactured with four different types of PCB-based winding structures, and it was analyzed in terms of the detection characteristics for standard calibration pulses and the changes of the output voltage according to the distance. The output increased linearly in accordance with the applied discharge amount. It was confirmed that the hexagon structure sensor had the highest sensitivity, because the winding cross-sectional area of the sensor was larger than others. In addition, as the distance from the defect increased, the output voltage of the sensors decreased by 7.32% on average. It was also confirmed that the attenuation rate according to the distance decreased as the input discharge amount increased. For the application of this new type sensor, PD electrode system was designed to simulate the void defect. Waveforms and PRPD patterns measured by the proposed PD sensors at DIV and 120% of DIV were the same as the results measured by MPD 600 based on IEC 60270. The proposed PD sensors can be installed on the inner wall of the transformer tank by coating its surfaces with a non-conductive material; therefore, it is possible to detect internal defects more effectively at a closer distance from the defect than the conventional sensors.

• Design & Manufacturing
• /
• v.16 no.4
• /
• pp.67-74
• /
• 2022

Injection molding is a cyclic process comprising of cooling phase as the largest part of this cycle. Providing efficient cooling in lesser cycle times is of significant importance in the molding industry. Recently, lots of researches have been done for rapid cooling of a hot-spot area using CO2 in injection molding. The CO2 flows under high pressure through small, flexible capillary tubes to the point of use, where it expands to create a snow and gas mixture at a temperature of -79℃. The gaseous CO2 removes heat from the mold and releases it into the atmosphere. In this paper, a CO2 cooling module was applied to an injection mold in order to cool a large area cavity uniformly and quickly, and the cooling performance of the injection mold was investigated. The product was a high-curvature molded part with a molding area of 300x100mm. Heat cartridges were installed in a stationary mold, and CO2 cooling module was inserted inside a movable mold. Through structural analysis, it was confirmed that the maximum deformation of mold with CO2 cooling module was 0.09mm. A CO2 feed system with a heat exchanger was used for cooling experiments. The CO2 was injected into the holes on both sides of the supply pipe of the cooling module and discharged through hexagon blocks to cool the mold. It took 5.8 seconds to cool the mold from an average temperature of 140℃ to 70℃. Through the experiment using CO2 cooling module, it was found that a cooling rate of up to 12.98℃/s and an average of 10.18℃/s could be achieved.

• The Journal of Korean Academy of Prosthodontics
• /
• v.52 no.1
• /
• pp.34-41
• /
• 2014

Purpose: In this study, the diameter of each implant driver was measured and compared to find out the compatibility of implant drivers. Materials and methods: Drivers from 12 implant systems being used in Dankook University Dental Hospital were included in this study. The shapes of the implant drivers were segregated, and the effective length and the diameter of upper, middle, lower part of driver tips were measured (n=10). The measured data were mathematically analyzed for its compatibility. Results: A driver with the smallest diameter (1.17 mm) had the highest compatibility at the upper part of driver tip. This driver could be used for a bigger driver up to 1.35 mm in diameter. There were several driver groups which had the same diameter so as to be interchangeable each other. In the middle part, the smallest diameter measured was 1.2 mm and this was able to replace a driver up to 1.40 mm diameter. Since the diameter generally became thicker from upper part (the tip of driver) to the lower part (the shank of driver), some drivers with bigger diameter at the upper part so which was failed to show any compatibility became compatible with a driver which had smaller diameter at the upper part but wider in the middle part. The compatibility of torx shape drivers were affected by the inner diameter of the drivers not only by the outer diameter. Furthermore, the inner diameter of torx drivers decided the compatibility between torx and hex drivers. Conclusion: From the study it was found that compatibility in drivers existed among certain implant systems and to check its compatibility the diameter at a certain effective length should be measured. However, there has been not enough studies about long-term use of compatible drivers, so effects of using compatible drivers on drivers and implants are unknown. Therefore, usage in inevitable cases only is recommended and further study is needed.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.8
• /
• pp.39-48
• /
• 2016

In this paper, we propose thermal resistance compact model of FinFET structure that has hexagon shaped source/drain. The heating effect and thermal properties were increased by reduced size of the device, and thermal resistance is an important factor to analyze the effect and the properties. The heat source and each contact that is moved heat out were set up in transistor, and domain is divided by the heat source and the four parts of contacts : source, drain, gate, substrate. Each contact thermal resistance model is subdivided as a easily interpretable structure by analyzing the temperature and heat flow of the TCAD simulation results. The domains are modeled based on an integration or conformal mapping method through the structure parameters according to its structure. First modeled by analyzing the thermal resistance to a single fin, and applying the change in the parameter of the channel increases to improve the accuracy of the thermal resistance model of the multi-fin/ finger. The proposed thermal resistance model was compared to the thermal resistance by analyzing results of the 3D Technology CAD simulations, and the proposed total thermal resistance model has an error of 3 % less in single and multi-finl. The proposed thermal resistance model can predict the thermal resistance due to the increase of the fin / finger, and the circuit characteristics can be improved by calculating the self-heating effect and thermal characterization.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.3
• /
• pp.439-455
• /
• 2018

This study was designed to analyze the behavior characteristics of people, who have the same or similar Investigative (I) and Enterprising (E) Holland code scores, toward their career commitment. The calculus of the two codes is .16, which means that they are inconsistent and full of oppositions. Especially, the focus of the analysis is whether there are any differences in career commitment between people who have similarly high or low scores of their I and E codes and, if there are differences, what are their characteristics The analysis shows that the participants with high scores of their I and E codes have strong career commitment. They are highly goal oriented and motivated and with a long future time perspective they seek for progress in their careers. Due to their high career expectations and career resilience, they are willing to invest in their careers and put up with a certain level of sacrifice. They place the emphasis on their independence and are not very influenced by the surrounding environment. While the participants with low scores of their I and E codes also perceive the importance of their career commitment, they are very much affected by people and external stimuli. As a result, their efforts in terms of their career commitment are easily disturbed and lowered. The critical factor causing the difference between these two types of people is related to the score of their Social(S) code. This research has the potential to provide improvement points for career counselling.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.1
• /
• pp.26-34
• /
• 1999

According to increase of nonlinear power electronics equipment, active power filters have been researched and developed for many years to compensate harmonic disturbances and reactive power. However the commercial of active power filter is being proceeded slowly, because the cost of active power filter compared to the passive filter for harmonic and reactive power compensation is expensive. Especially, the use of DSP (Digital Signal Processing) chip, which is frequently used to control 3-phase active power filter, is a factor of increasing the cost of active power filters. On the other hand, the use of only analog controller makes the controller's circuits much more complicate and depreciates the flexibilities of controller. In this paper, a controller with low cost for 5[kVA] 3-phase active power filter system is designed. To reduce the expense of active filter system, the presented controller is composed of digital control part using Intel 80C196KC $\mu$P and analog control part using hysteresis controller for current control. Characteristic analysis of designed controller for active filter system is performed by computer simulation and compensating characteristics of the designed controller are verified by experiment.tegy can apply to the vector control, leading to better output torque capability in the ac motor drive system. This strategy is that in the overmodulation range, the d-axis output current is given a priority to regulate the flux well, instead the q-axis output curent is sacrificed. Therefore, the vector control even in the overmodulation PWM operation can be achieved well. For this purpose, the d-axis output voltage of a current controller to control the flux is conserved. the q-axis output voltage to control the torque is controlled to place the reference voltage vector on the hexagon boundary in case of the overmodulation. The validity of the proposed overall scheme is confirmed by simulation and experiments for a 22[kW] induction motor drive system.

• Applied Biological Chemistry
• /
• v.28 no.1
• /
• pp.19-27
• /
• 1985

The physicochemical properties of starch isolated from Yullmoo (Coix lachrymajobi var. mayuen stapf.) and Yeomjoo (Coix lachryma-jobi L.) were investigated. The average diameters of starch granules of Yullmoo and Yeomjoo were 12.0 microns, both of all, and the shape of these starch granules were hexagon, octagon and round. X-ray diffraction patterns of two samples were A-types and amylose contents of Yullmoo and Yeomjoo starch were 0% and 23%, respectively, iodine affinities of these were 0.08% and 4.2%, respectively, blue values and alkali numbers of these were 0.13 and 0.43, 2.4 and 7.2, and raising power of these were 280 and 20, respectively. Yullmoo starch had higher swelling power than Yeomjoo starch. The increase in optical transmittance of 0.1% suspensions of Yullmoo and Yeomjoo starches occurred at $60^{\circ}C$ and continued up to $75^{\circ}C$ for Yullmoo, $85^{\circ}C$ for Yeomjoo. Amylogram data on 5% of Yullmoo and Yeomjoo starch suspensions showed that gelatinization temperatures and maximum peak heights of Yullmoo and Yeomjoo were $68.5^{\circ}C\;and\;78^{\circ}C$, 920 and 310 B.U., respectiyely. Intrinsic viscosities of Yullmoo and Yeomjoo starches were 1.49 and 1.77, respectively, and interaction coefficients of the two starches were 0.57 and 0.56, respectively The extent of retrogradation determined at $2^{\circ}C$ showed that retrogradation occurred slowly with Yullmoo starch paste tut little with Yullmoo.

• Journal of Cadastre & Land InformatiX
• /
• v.48 no.1
• /
• pp.123-138
• /
• 2018

To sustainably monitor air pollution in Seoul, the number of Air Pollution Monitoring Station has been gradually increased by Korea's Ministry of Environment. Although particulate matters(PM), one of the pollutants measured at the stations, have an significant influence on human body, the concentration of PM in Korea came in second among 35 OECD member countries. In this study, using the data of PM concentration from the stations, distribution maps of PM10 and PM2.5 concentrations over Seoul were generated, and spatial factors potentially related to PM distribution were investigated. Based on a circumscribed hexagon about a circle in radius of 500 meters created as a basic unit, Seoul was sectionalized and PM concentration map was generated using the interpolation technique of 'inverse distance weighting'. The distributions of PM concentrations were investigated with commuting time by administrative district and the outcome was related with land-use type and volume of traffic. Results from this analysis indicated distribution pattern of PM10 concentration was different from that of PM2.5 by administrative district and time. The distribution of PM concentration was strongly related to not only the size of business and trafficked areas among the land-use type, but also the existence of urban green. Further analysis of the relationship between the PM concentration and detailed land-use and urban green maps can be helpful to identify spatial factors which have an impact on the PM concentration on the regional scale.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.6
• /
• pp.237-241
• /
• 2014

We investigated the optimal etching conditions and properties of the surface change due to molten KOH/NaOH chemical wet etching using an AlN wafer which has been put to practical use in the present study. Results were observed using a scanning electron microscope after 5 minutes etching at $350^{\circ}C$, was found to have a surface form of the respective other Al-face, the N-face. In particular, etch-pit in the form of a hexagon, which is observed in the Al-face appeared, It was calculated at $2{\times}10^6/cm^2{\sim}10^{10}/cm^2$ dislocation density. In the case of N-face, lattice defects in the form of the hexagonal pyramids is formed. It was discovered that in order to observe the orientation of the wafer, which corresponds to the C-axis direction of the resulting hexagonal AlN which was analyzed using XRD (0002) and is a state of being oriented in the (0004) plane. The Radius of curvature of AlN wafer was 1.6~17 m measured by DC-XRD rocking curve position.

• The Journal of Korean Academy of Prosthodontics
• /
• v.58 no.2
• /
• pp.103-109
• /
• 2020

Purpose: The purpose of this study was to evaluate the preload maintenance of the retaining screw when using anaerobic sealing agents in implant fixture and abutment components. Specifically, the study examines the effects of anaerobic sealing agents on different types of screws. Materials and methods: External hexagon implants made of titanium and anti-rotational abutments were used. Titanium abutment screws and ebony abutment screws from the same manufacturer were used. The experiment was divided into four groups (n = 10 in each group). In the control group, no sealing agent was used at the implant fixture and abutment screw interface. All abutment screws were tightened according to the manufacturer's recommended torque (30 N.cm). After 24 hours, the removal torque (detorque) of each screw was measured using a digital torque gauge device. The data were analyzed by two-way ANOVA test according to normality distribution satisfaction. Results: Looking at the results for each group, titanium screws and no treatment showed detorque values of 20.3 ± 1.6 N.cm. titanium screws and applied anaerobic sealing agent showed detorque values of 32.4 ± 6.7 N.cm. Ebony screws and no treatment showed detorque values of 20.2 ± 1.5 N.cm. ebony screws and applied anaerobic sealing agent showed detorque values of 30.4 ± 4.5 N.cm. Conclusion: The detorque value was higher in the case of using anaerobic sealing agents in both the titanium screw and ebony screw groups. But there was no difference between the two screws.