• Journal of the Korean Association of Geographic Information Studies
• /
• v.25 no.2
• /
• pp.59-71
• /
• 2022

This study considered regional differences in the university-industry collaboration of Korean universities and performed cluster analysis to identify the spatial range with high university-industry collaboration connectivity. By university establishment type, it was found that the university-industry collaboration capacity of the major national university was superior overall, especially in the technology transfer & commercialization sector and the infrastructure sector, compared to private universities and general national universities. The spatial pattern of university-industry collaboration capacity showed relatively clear differences by city and province. In terms of university-industry collaboration capacity by sector, it was confirmed that the regional gap was not large in the talent training sector and the infrastructure sector, but the regional gap was relatively large in the technology transfer & commercialization sector and the start-up sector. As a result of the cluster analysis to identify a spatial range with high connectivity in terms of similarity and spatial proximity of university-industry collaboration patterns, it is divided into 15 clusters. It is found that most of major national universities are included in one of 15 clusters where all sectors of university-industry collaboration are strong. Therefore, as a policy measure to achieve regional innovative growth through enhancing the effectiveness of university-industry collaboration, we propose the establishment of a hub & spoke network-type collaboration system in which a major national university acts as a hub and nearby local universities play a spoke role.

• Journal of Environmental Impact Assessment
• /
• v.31 no.1
• /
• pp.1-10
• /
• 2022

This study was carried out to understand the water quality characteristics of the initial stormwater runoff and the origin of soluble pollutants according to various rainfall conditions from a non-point source reducing facility. The water sample from this study was collected among 10 collection facilities in the G-drainage area. Specifically, five of the collection points including #1, #5, #8, #9, and #10 were reported with unknown water inflow even during non-rain conditions. The leakage characteristics of non-point pollutants from the collection facilities were then able to identify accordingly. The water quality characteristics of the stormwater runoff from the collection facilities were strongly affected by the amounts of rainfalls. The average concentrations of EC, BOD, TOC, and TN during non-rain were found to be higher than their concentrations during rain; on the other hand, the average concentrations of DO were found to be lower than its concentrations during rain. In addition, the distribution of organic components existing in the effluent of collection facilities were identified based on the dissolved organic matter analysis. In summary, the stormwater runoff was highly affected by pollutants flowing from the surrounding environment, and the amounts of hard-to-decompose humic substances were greatly increased in the collection facilities due to rain.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.35 no.3
• /
• pp.273-281
• /
• 1990

Two rice varieties, Samkangbyeo and Sangpungbyeo, were transplanted on 1/2000a pots at 6 different dates beginning on May 11 with 10 day interval in 1987 and at 4 different dates beginning on May 21 with 10 day interval in a paddy field at the Chungbuk Provincial Rural Development Administration. Dry matter distributions to stem and leaf sheath, leaves and ear at different growth stages were analyzed to provide basic informations neccessary for the development of dynamic growth model. Dry matter production was reduced as transplanting was delayed and the degree of reduction was greater at the transplanting later than June 1. Dry matter distribution to stem and leaf sheath was increased up to 60-70 days after transplanting with the maximum ratio between 60-70%, which were decreased to 37-43% in pots and 27-33% in field at the end of ripening stage. On the other hand, dry matter distribution to leaf blade was decreased from 40-50% at transplanting to 11-17% at harvesting. Ear dry matter distribution increased rapidly after heading and the distribution ratio was 42-49% in pots and 52-62% in field. Although regression equations to predict dry matter distribution to different parts of rice plant were satisfactory for individual experiment, the application to different experiment was not appropriate.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.35 no.4
• /
• pp.328-333
• /
• 1990

In developing dynamic growth model of a crop, it is important to estimate accurate dry matter partition to different parts of crop plants. Two rice varieties, Samkang and Chucheong, were transnplanted with three planting densities of 72. 90 and 120 hills per 3.3㎡ on May 30 and June 15 in 1988 to study the effect of planting density on dry matter partition in rice plants. Total dry wight per square meter of two varieteis in May 30 transplanting were greater than those in June 15 transplanting. Total dry wights were increased as planting density was increased. The response of dry weights of differents parts of rice plants per hill were decreased as the density was increased. Although the difference in dry weights of leaf blade and stem and sheath between two varieties was not great, greater ear weight of Samkang resulted in greater total dry weight than that of Chucheong. Despite of transplant in date and planting density on dry weights, the ratio of dry matter partition to different parts of rice plants at a certain growth stage remained constant. Estimated dry weights of different parts at two stages of growth based on average ratio of dry matter partition over two transplantion dates and planting densities agreed well with those observed.

• Journal of the Society of Disaster Information
• /
• v.19 no.2
• /
• pp.292-304
• /
• 2023

Purpose: This study was conducted to obtain experimental data for the establishment of preventive measures against fire, as large and small fire accidents occur at production and storage sites of superabsorbent polymers developed for the convenience of daily life. Method: The sample container was fixed at 0.2m in both length and width, and was shaped into a rectangular cuboid with heights of 3cm, 5cm, 7cm, and 14cm to access an infinite flat plane. The sample container was fixed in the center of a thermostatic bath that was heated to a predetermined temperature according to a preset temperature control program. If the central temperature of the sample rose more than 20℃ above the set temperature, it was determined to have 'ignited', and if it remained similar to the set temperature, it was determined to have 'unignited'. Result: The critical autoignition temperature was calculated to be 212.5℃ for a sample container with a height of 3cm, 202.5℃ for 5cm, 192.5℃ for 7cm, and 177.5℃ for 14cm. The ignition induction time to reach the highest temperature was approximately 42hours for 3cm, 91hours for 5cm, 151hours for 7cm, and 300hours for 14cm. Conclusion:① As the size of the sample container increased, the autoignition temperature decreased and the ignition induction time to reach the highest temperature increased. ② The apparent activation energy was calculated to be 39.30kcal/mol, with a correlation of 99.5%.

• Journal of the Society of Disaster Information
• /
• v.19 no.2
• /
• pp.280-291
• /
• 2023

Purpose: As fire accidents happen at the production and storage sites of superabsorbent polymers for convenience of daily life, an experimental study was conducted to secure basic data to establish practical preventive measures against them. Method: The sample container (20cm width × 20cm length) was made into a rectangular cuboid with the heights of 3cm, 5cm, 7cm, and 14cm, respectively, to allow access to the infinite flat plane. The front and back of the container were covered with a 300-mesh stainless steel mesh for one-dimensional heat transfer. The sample container was placed in the center of the thermostatic bath, which was heated to a predetermined temperature by setting the thermostat program in advance, and it was determined to be 'ignited' when the central temperature of the sample rose by more than 20℃ above the set temperature, and "unignited" when it was maintained at an approximate value of the set temperature. Result: The critical autoignition temperature was calculated to be 217.5℃ when the height of the sample container was 3 cm, 212.5℃ when it was 5 cm, 202.5℃ when it was 7cm, and 187.5℃ when it was 14cm. The ignition induction time to reach the maximum temperature was 34hours for 3cm, 76hours for 5cm, 143hours for 7cm, and 318hours for 14cm. Conclusion: ① As the size of the container increased, the autoignition temperature decreased and the induction time to reach the maximum temperature increased. ② An apparent activation energy was calculated to be 44.92kcal/mol, with a correlation of 96.93%.

• Korea Trade Review
• /
• v.42 no.4
• /
• pp.93-114
• /
• 2017

Under the FTA agreement, preferential tariffs between FTA members will result in tariff reductions. In order to ensure the stable use of the FTA tariff system, it is necessary for the customs authorities to determine whether the origin goods are clearly applicable. This study analyzed the procedure of appeal according to the origin verification system based on the decision made by Korea Customs Service and Tax Tribunal. From this, we examined whether the rate of re-claiming a case rejected in the 'Review System of the Legality Before Taxation' differs. In addition, we carried out a quantitative analysis using bootstrapping technique in order to overcome the scarcity cases of verification of origin among FTA members. The implications of this paper are summarized as follows: First, we tested the hypothesis that the re-claiming rate of Western countries is higher. Second, some issues represented higher re-claiming rate. Third, there was no significant difference between the verification group and the re-claiming rate. Finally, even if an applicant makes a claim again, there is a possibility of being rejected again.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.4D
• /
• pp.687-693
• /
• 2006

Image co-registration is the process of overlaying two images of the same scene, one of which represents a reference image, while the other is geometrically transformed to the one. In order to improve efficiency and effectiveness of the co-registration approach, the author proposed a pre-qualified area matching algorithm which is composed of feature extraction with canny operator and area matching algorithm with cross correlation coefficient. For refining matching points, outlier detection using studentized residual was used and iteratively removes outliers at the level of three standard deviation. Throughout the pre-qualification and the refining processes, the computation time was significantly improved and the registration accuracy is enhanced. A prototype of the proposed algorithm was implemented and the performance test of 3 Landsat images of Korea. showed: (1) average RMSE error of the approach was 0.435 pixel; (2) the average number of matching points was over 25,573; (3) the average processing time was 4.2 min per image with a regular workstation equipped with a 3 GHz Intel Pentium 4 CPU and 1 Gbytes Ram. The proposed approach achieved robustness, full automation, and time efficiency.

• Proceedings of the Plant Resources Society of Korea Conference
• /
• 2020.08a
• /
• pp.68-68
• /
• 2020

최근 농촌진흥청과 기상청에서 발표한 연구자료에 따르면 2020년 기준으로 국내 경지면적의 10% 가량이 이미 아열대 기후대에 속하고 있을 뿐 현재 추세대로 온실가스가 배출될 경우 2100년경 우리나라의 대부분 지역은 아열대 기후대에 속하게 될 것으로 전망되고 있다. 이에 국가 기관뿐만 아니라 많은 지자체에서 기후변화에 대응하여 아열대 작물을 도입하기 위한 시도를 활발하게 추진하고 있다. 아열대 작물 중 국내에서 3번째로 많이 활용되고 있는 삼채는 기능성 물질을 다량으로 함유하고 있어 수요도가 지속적으로 증가하고 있다. 하지만, 삼채의 경우 일반적인 원예 작물과는 달리 실생 종자를 상업적으로 이용하고 있어 종자들의 발아율이 균일하지 못할 뿐만 아니라 발아율이 낮은 문제가 있는 것으로 보고되고 있다. 이에 삼채의 경우 농가에서 정식 시기를 맞추기 어려울 뿐만 아니라 대규모 생산을 위한 공정육묘 시스템의 적용이 어려운 상황에 있다. 종자 프라이밍 기술은 잠재적으로 종자 발아와 식물 생장을 빠르고 균일하게 해줄 수 있는 방법으로 알려져 있지만, 현재 삼채에서는 프라이밍 처리가 종자 발아에 미치는 영향에 대해서 검토한 사례가 없다. 따라서 본 연구는 삼채의 파종 효율을 증진시키기 위한 목적으로 몇 가지 프라이밍 처리 방법이 삼채의 발아특성에 미치는 영향을 검정하고자 하였다. 삼채 종자는 (주)아람종묘사의 종자를 구매하여 강릉원주대학교 생명과학대학에서 수행하였다. 프라이밍 처리는 Hydropriming은 증류수, Osmopriming은 CaCl2 1.0%, Halopriming은 Polyrthylene glycol 6000(PEG) 13.5%의 3가지를 사용하였으며, 각 프라이밍 처리 시간은 6시간, 12시간, 18시간, 24시간, 48시간 총 5가지 방법으로 처리되어 대조구를 포함 총 16개의 처리를 하였다. 프라이밍 처리 된 종자는 페트리디쉬 (50mm)에 30립씩 치상하였다. 프라이밍 각 처리구별 4반복으로 하였으며 24시간 암(Black), 온도 20℃의 조직배양실에서 치상 후 10일간 조사하였다. 본 실험 결과 대조구는 38% 발아율을 가졌으며, 프라이밍 처리 시간에 따른 각 처리구들은 대조구에 비해 발아율이 높아짐을 확인할 수 있었다. 그 중 Hydropriming 12시간 발아율 51%, Osmopriming 18시간 발아율 68%, Halopriming 48시간 발아율 65%로 각 프라이밍 처리구별 가장 좋은 발아율을 확인할 수 있었다. 결론적으로 삼채에서 프라이밍 처리 기술의 적용은 발아율의 향상과 발아기간의 정형화를 유도할 수 있어 농가에서의 일반 육묘는 물론이고 대규모 공정육묘를 위한 저렴하고 안전한 방법 중 하나로써 이용될 수 있을 것으로 기대되어 진다.

• The Journal of Engineering Geology
• /
• v.33 no.4
• /
• pp.701-716
• /
• 2023

Microplastics (<5 mm diameter) in aquatic environments adsorb heavy metals, potentially exposing humans to their toxic effects via food chains. We investigated factors influencing the adsorption of heavy metals on microplastics in aquatic environments, examining their adsorption processes and mechanisms. Adsorption characteristics vary with polymer type, crystallinity, particle size, and environmental conditions (pH, temperature, weathering), and the adsorption capacity for heavy metals increases with weathering and reduction in polymer particle size. However, correlations between environment temperature, polymer crystallinity, and adsorption capacity for heavy metals could not be confirmed. The adsorption behavior of heavy metals can be explained in terms of physicochemical adsorption processes and evaluated through adsorption kinetics and isothermal studies, with multiple mechanisms usually being involved. An understanding of the adsorption of heavy metals by microplastics should aid evaluation of the potential risks of microplastics in aquatic environments.