• The KSFM Journal of Fluid Machinery
• /
• v.4 no.1 s.10
• /
• pp.7-13
• /
• 2001

In developing a multistage compressor, the stage matching is one of the critical design issues. The mismatching can be often observed even if each stage has been proven good and then used as part of a compression system. A good matching among the stages can be achieved by changing various design parameters (i.e., passage cross sectional areas, blades angles, stagger angles, curvature, solidity, etc.). Therefore, designers need to find out what parameters must be changed and how much. In this study, a method to search the design parameters for optimum stage matching has been used based on an 1-D mathematical model of a compressor, which uses the data obtained from the preliminary test to identify the design parameters. This methodology is applied with a two-stage axial compressor, which was originally designed for a helicopter gas turbine engine. After identifying design parameters using preliminary test data, an optimization process has been employed to achieve the best matching between the stages (i.e., maximum efficiency of the compressor at its operation modes within a given range of the rotor speed under given restrictions for required stall margins and mass flow). 3-D flow calculations have been performed to confirm the usefulness of the corrections based on the 1-D mathematical model. Calculational results agree well with the experimental data in view of the performance characteristics. Some promising results were produced through the methodology proposed in this paper in conjunction with flow calculations.

• Transactions of the KSME C: Technology and Education
• /
• v.2 no.2
• /
• pp.113-124
• /
• 2014

In developing an aircraft, configuration determination and requirement proofing depend on flight test results. Since the flight tests require much time and high cost, systematic flight test planning and analysis are needed to reduce cost and development time. This paper presents a desirability function approach to present an integrative measure of vibration levels at important positions and suggests a fractional factorial design which is one of the experimental design methods to help perform systematic flight tests. A method to perform flight tests in stages is also suggested to further reduce the number of flight tests.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.10
• /
• pp.761-769
• /
• 2013

Effects of helicopter wakes on helicopter aerodynamics are serious, but the wake configuration is very complicated and hard to predict. The purpose of this study is the detailed observation of wake using numerical methods. Vortex lattice method and freewake method are used to track the vortices in the wake. In this paper, the wake configuration is observed during hovering flight. In the case of hovering flight at the moderate thrust level, besides tip vortex, counter-rotating vortex can be observed at the inboard part of blade. When the vortices move downward, tip vortex and counter-rotating vortex get close and influence to each other. Therefore, vortices are highly distorted due to their own instability.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.11
• /
• pp.1049-1059
• /
• 2010

This paper treats the aerodynamic optimization of the blade planform for helicopters. The blade shapes, which should be determined during the threedimensional aerodynamic configuration design step, are defined and are parameterized using the B$\acute{e}$zier curves. This research focuses on the design approaches generally adopted by industries and or research institutes using their own experiences and know-hows for the parameterization and for the definition of design constraints. The hover figure of merit and the equivalent lift-to-drag ratio for the forward flight are used to define the objective function. The resultant nonlinear programming (NLP) problem is solved using the sequential quadratic programming (SQP) method. The applications show the present method can design the important planform shapes such as the airfoil distribution, twist and chord variations in the efficient manner.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.1
• /
• pp.64-71
• /
• 2006

For SUAV is required to have the capacity of VTOL and fast forward flight, the SUAV development program has decided to adopt the tiltrotor mechanism which includes helicopter and turboprop mechanisms. From the engine point of view, the key engine parameters such as engine operating mechanism, engine control scheme, the dynamics characteristic of power train, engine intake/exhaust concept, and engine installation requirements should fulfill the requirements of the two different mechanisms, helicopter and turboprop. And for the maximum efficiency of the rotor, rotational speed for the two modes are 20% different, the power train shall find a way to make it so. Meeting these specific requirements for the tiltrotor mechanism, this research begins with a conventional OTS(off-the-shelf) turboshaft engine survey and minimizes engine modification to develop an economical propulsion system. The engine technical review has been performed on the basis of those requirements and capabilities.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.1
• /
• pp.41-51
• /
• 2018

Downwash from helicopter rotor blades and external winds from various maneuvering make an unguided rocket change its trajectory and range. For the prediction of the trajectory and range, it is essential to consider the downwash effect. In this study, an algorithm was developed to calculate 6-Degree-Of-Freedom(6 DOF) forces and moments exerting on the rocket, and total flight trajectory of a 2.75-inch unguided rocket in a helicopter downwash flow field. Using Actuator Disk Model(ADM) analysis result, the algorithm could analyze the entire trajectory in various initial launch condition such as launch angle, launch velocity, and external wind. The algorithm that considered the interference between a fuselage and external winds could predict the trajectory change more precisely than inflow model analysis. Using the developed algorithm, the attitude and trajectory change mechanism by the downwash effect were investigated analyzing the effective angle of attack change and characteristics of pitching stability of the unguided rocket. Also, the trajectory and range changes were analyzed by considering the downwash effect with external winds. As a result, it was concluded that the key factors of the rocket range change were downwash area and magnitude which effect on the rocket, and the secondary factors were the dynamic pressure of the rocket and the interference between a fuselage and external winds. In tailwind case which was much influential on the range characteristics than other wind cases, the range of the rocket rose as increasing the tailwind velocity. However, there was a limit that the range of the rocket did not increase more than the specific tailwind velocity.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.9
• /
• pp.92-100
• /
• 2017

The Helicopter MRA Control Rod System has the important function of controlling the speed, height, and direction of helicoptersby adjusting the main rotor disc. However, the ingress of water into the inner control rod can cause ice damage in the rod during winter operation and also corrosion;these defects need to be rectified. The water flowed into the control rod through the upper side space, and the rod was cracked during icing expansion occurring at low temperature. The corrosion occurred due to the lack of coating process during the manufacturing process. To resolve these problems, the upper rod was sealed to prevent water inflow and a coating process was added to prevent corrosion. These solutions were verified by awaterproof test and a salt fog test. The phenomena, causes and measures were reviewed and the methods of improvement were established and proven. This proposed technology to prevent water infiltration and corrosion will contribute to the safety of rotary wing aircraft.

• International Journal of Aeronautical and Space Sciences
• /
• v.18 no.2
• /
• pp.186-196
• /
• 2017

In order to resolve the trimming difficulty in rotor CFD calculations, a high-efficiency and improved "delta trim method" is established to compute the blade control settings that are necessary to identify the blade motion. In this method, a simplified model which combines the blade element theory and different inflow models is employed to calculate the control settings according to the target aerodynamic forces, then it is coupled into a CFD solver with unsteady Navier-Stokes equations by the delta methodology, which makes the control settings and aerodynamics calculated and updated in the meantime at every trim cycle. Different from the previous work, the current research combines the inflow model based on prescribed wake theory. Using the method established, the control settings and aerodynamic characteristics of Helishape 7A, AH-1G and Caradonna-Tung rotors are calculated. The influence of different inflow models on trimming calculations is analyzed and the computational efficiency of the current "delta trim method" is compared with that of the "CFD-based trim method". Furthermore, for the sake of improving the calculation efficiency, a novel acceleration factor method is introduced to accelerate the trimming process. From the numerical cases, it is demonstrated that the current "delta trim method" has higher computational efficiency than "CFD-based trim method" in both hover and forward flight, and up to 70% of the amount of calculation can be saved by current "delta trim method" which turns out to be satisfactory for engineering applications. In addition, the proposed acceleration factor shows a good ability to accelerate the trim procedure, and the prescribed wake inflow model is always of better stability than other simple inflow models whether the acceleration factor is utilized in trimming calculations.

• Composites Research
• /
• v.33 no.6
• /
• pp.353-359
• /
• 2020

In this work, a contour-based section analysis method incorporating the use of Bézier curves is attempted for the construction of optimal structural design framework of composite helicopter blades. The suggested section analysis method is able to analyze composite blades with solid cores made of arbitrary materials and geometric shapes. The contour-based section analysis method is integrated into a blade structural optimization framework to confirm the efficiency of the present approach. The numerical simulation result demonstrates that the optimized blade configurations are obtained with a reduction in mass by 52%, compared to the baseline blade. For the structural optimization of composite blades with 19 subsections, it takes about one hour for the successful optimization while satisfying all the design constraints considered in this study, which reveals the efficiency of the present approach.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.256-263
• /
• 2008

The assumed modes method is developed to derive a set of linear differential equations describing the motion of a flexible wind turbine blade and to propose an approach to investigate the forced responses result from various wind excitations. In this work, we have adopted Euler beam theory and considered that the root of the blade is clamped at the rigid hub. And the aerodynamic parameters and forces are determined based on Blade Element Momentum (BEM) theory and quasi-steady airfoil aerodynamics. Numerical calculations show that this method gives good results and it can be used fur modeling and the forced vibration analysis including the coupling effect of wind-turbine blades, as well as turbo-machinery blades, aircraft propellers or helicopter rotor blades which may be considered as straight non-uniform beams with built-in pre-twist.