• 한국연소학회:학술대회논문집
• /
• 2000.05a
• /
• pp.26-34
• /
• 2000

Geometry change of burner nozzle has influence on fuel atomizing and combustion characteristics. NOx reduction technologies can be divided into two method; Before combustion method(NOx treatment of fuel) and After combustion method(NOx treatment of flue gas). In this study, experiments are carried out using difference nozzle and combustion condition change to reduce NOx in heavy oil fired thermal utility boiler. These methods have advantage like easy application and low installation cost. By this method NOx can be reduced by 18% and maintain CO emission level.

• Journal of the Korean Society of Combustion
• /
• v.20 no.1
• /
• pp.15-23
• /
• 2015

This paper presents the results of field demonstration for fuel switching to bio-fuel oil in 4 commercial heavy oil fired power plants. The 100% fuel switching field demonstration was successfully carried out in two tangential-firing boilers at a capacity of 75 and 100 MWe respectively without major equipment retrofit, and also 25% bio-fuel oil blending for two opposite firing boilers at a capacity of 350 and 400 MWe respectively. Despite the low density and heating value, the bio fuel was successfully replaced heavy fuel oil at the full load by only adjusting operational parameters. Incase of bio fuel oil combustion, heat absorption of radiative heat transfer section was reduced while convection section has opposite trend. In pollutants emission, a major reductionin SOx as well as 10-20% reduction in NOx were achieved by the fuels witching. On the other hand, boiler efficiency was slightly underestimated.

• 한국연소학회:학술대회논문집
• /
• 2004.11a
• /
• pp.244-249
• /
• 2004

Experiments were performed to investigate the characteristics of combustion of 7MW-3 air stages combustion system for a heavy oil firing boiler. Several fuel nozzles were developed for the purpose of lowering pollutions in another institute and ${\Phi}$-jet nozzle among them was equipped to the combustion system. A variety of combustion phenomena were observed as air stage ratio, air fuel ratio and load are changed for each nozzle. Main combustion characteristics are shape of flame, NOx and CO generations, smoke scale number. Through lots of adjustments, the combustion system reaches such goals as the low NOx of 160 ppm, CO of 300 ppm corrected at $O_2$ of 4% and dust of 150 mg/Sm3.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 2004.05a
• /
• pp.263-268
• /
• 2004

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06a
• /
• pp.105-110
• /
• 2006

In order to utilize coal fly ash (hereafter : coal ash ) discharged from coal boiler as a material for civil engineering usage such as snow melter or soil improver, we have to prevent leaching hazardous elements such as fluorine boron and heavy metals from the coal ash because the leaching concentrations of some elements in the ash exceed the Japanese standards for environmental soil quality. Through the laboratory experiments and mill trials we confirmed that the leaching concentrations of fluorine, boron and heavy metals were maintained below their environmental standards by mixing with fixation chemicals and curing for a short time.

• Transactions of the Korean hydrogen and new energy society
• /
• v.33 no.1
• /
• pp.77-84
• /
• 2022

The experimental work has been carried out for the study of pyrolysis of oil samples used in industrial and utility boilers in Korea. For five oil samples, the characteristics of pyrolysis have been investigated with a thermogravimetric analyzer (TGA), and their kinetic parameters were obtained and compared each other. The rate order of pyrolysis rate for five oils were as follows: by-product fuel oil, pyrolysis oil, diesel, a heavy oil and refined oil. The pyrolysis of refined oil has been successfully described by the three step, first order reaction model while the single step reaction model has been used for other oils. For the reaction temperature over 550 K, the reactivity of refined oil was very poor compared with other oils.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.11
• /
• pp.1578-1584
• /
• 2002

Combustion stability is one of the most important factors that must be considered in burning of heavy fuel oil, especially low-grade oil. This paper describes the combustion characteristics of petrochemical process by- product in the combustion furnace of heavy fuel oil. Main experimental parameters were combustion load, excess 02, fuel preheating temperature and air/fuel ratio. The capacity of CRF(combustion research facility) used in this study was 1.0 ton/hr and the burner is steam jet type suitable far heavy oil combustion and manufactured by UNIGAS in Italy. The fuel used in this experiment were 0.5 B-C, petrochemical process by-product and 3 kinds of 0.5 B-C/process by-product mixtures. The combustion stability was monitored and exhaust gases such as CO, NOx, SOx and particulates were measured with the excess $O_2$ and combustion load. The main purpose of this study is to clarify whether process by-product can be used as a boiler fuel or not in consideration of flame stability and emission properties.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.2
• /
• pp.292-299
• /
• 2004

This study is intended to check a temperature of the flame to raise by burning A heavy oil in a boiler. to measure the concentration of DS and SOF after collecting the PM(Particulate Matters). and to analyze the components ingredients of SOF by G.C Mass for presupposing the generation of particulate matters(soot). It is thought that the methyl(CH3) of the cyclic compound is changed to the materials of 2 cycles and 3 cycles after becoming CH by dehydrogenation and also mixing with the CH of a chain compound. form H-$\cdot$C=C$\cdot$-H that is mentioned before. in order to become Polycyclic Aromatic Hydrocarbon.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2002.02a
• /
• pp.217-222
• /
• 2002

본 연구에서는 가연성 폐기물을 이용한 시설원예 난방에너지 공급시스템 개발을 위하여 대형 온실 난방이나 RPC 시설에 이용할 수 있는 왕겨와 중유 겸용연소 시스템에서 중유의 연소 및 성능 특성을 분석하고자 하였다. 중요 인자로는 분사노즐의 크기(2.0, 2.25, 2.5, 3.0 GPH)와 진공압력(375, 500, 625, 750 Pa)을 설정하였으며 이에 대한 결과를 요약하면 다음과 같다. 1.진공압력 500Pa조건에서 연료 공급율이 증가할수록 연소실 벽체 열교환기 효율은 감소하고 폐열회수 열교환기와 사이클론 열교환기의 효율이 증가하였으며, 노즐 2.5GPH에서 진공압력이 커질수록 연소실 하부의 온도가 감소하였고 연소실 상부에서는 비슷한 경향을 보였다. 2, 연소온도특성, 열효율, 배기가스 성분분석 등의 결과로 볼 때 최적의 연소 조건은 노즐 2.5GPH는 진공압력 375Pa, 노즐3.0GPH는 진공압력 500Pa과 625Pa 사이로 판단되었다. 3. 배연가스내의 대기오염 성분은 모든 실험처리에서 CO 함량은 거의 없고 SO$_2$와 NO$_{x}$의 함량 또한 일반 보일러 허용기준을 만족하는 것으로 나타났다.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.4
• /
• pp.985-994
• /
• 2018

Bio-heavy oil for power generation is a product made by mixing animal fat, vegetable oil and fatty acid methyl ester or its residues and is being used as steam heavy fuel(B-C) for power generation in Korea. However, if the fuel supply system of the fuel pump, the flow pump, the injector, etc., which is transferred to the boiler of the generator due to the composition of the raw material of the bio-heavy oi, causes abrasive wear, it can cause serious damage. Therefore, this study evaluates the fuel characteristics and lubricity properties of various raw materials of bio-heavy oil for power generation, and suggests fuel composition of biofuel for power generation to reduce frictional wear of generator. The average value of lubricity (HFRR abrasion) for bio-heavy oil feedstocks for power generation is $137{\mu}m$, and it varies from $60{\mu}m$ to $214{\mu}m$ depending on the raw materials. The order of lubricity is Oleo pitch> BD pitch> CNSL> Animal fat> RBDPO> PAO> Dark oil> Food waste oil. The average lubricity for the five bio-heavy oil samples is $151{\mu}m$ and the distribution is $101{\mu}m$ to $185{\mu}m$. The order of lubricity is Fuel 1> Fuel 3> Fuel 4> Fuel 2> Fuel 5. Bio-heavy oil samples (average $151{\mu}m$) show lower lubricity than heavy oil C ($128{\mu}m$). It is believed that bio-heavy oil for power generation is composed of fatty acid material, which is lower in paraffin and aromatics content than heavy oil(B-C) and has a low viscosity and high acid value, resulting in inhibition of the formation of lubricating film by acidic component. Therefore, in order to reduce friction and abrasion, it is expected to increase the lubrication of fuel when it contains more than 60% Oleo pitch and BD pitch as raw materials of bio-heavy oil for power generation.