• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.1
• /
• pp.165-173
• /
• 2014

The method of emission inspection for Heavy-duty diesel vehicles has been engine speed type Lug-down 3mode. This method could bring damage to decrepit vehicles under high speed and high load condition and it could not apply the driving pattern on the road. For these reasons, this study has started to create new emission inspection which is appropriate for Korea's road infrastructure. KD 147 would be applied to light-duty diesel vehicles from july 2010 after model operations. Therefore, this study has investigated new emission inspection system for heavy-duty diesel vehicles, except for light-duty diesel vehicles. In consideration of domestic conditions to meet the new load test method in this study, the Lug-down3 mode vehicle speed method was developed for the first time in korea.

• Journal of Korean Society for Atmospheric Environment
• /
• v.21 no.6
• /
• pp.585-592
• /
• 2005

Nowadays it has been strongly required to control emissions from vehicles specially in diesel engines because of increasing number of vehicle in korea. This research aims to provide with some of deterioration factors on vehicles for emissions characteristics and the test was done on an electronically controlled heavy-duty diesel engine under severe driving conditions such as 1200 driving hours, 220,000 km driving distance and a full load. Under various driving conditions, CO, HC, $NO_{x}$, PM and Soots emissions were estimated under D-13 mode and D-3 mode respectively. CO emission was not changed until 500 running hours, and as engine aging is progressed THC was not changed until 500 running hours but it decreased to about $33\%,\;NO_{x}$ decreased constantly but on the other hand PM increased up to $6.9\%$ during the aging process.

• Journal of Power System Engineering
• /
• v.10 no.2
• /
• pp.11-15
• /
• 2006

The increasing numbers of automobiles keep causing air-pollution problems worse than ever. Nowadays, research on catalyst converter and filter trap as a modern technology is very active because PM is designated as a major cancer material and stringent regulations on this are necessary and required. This research emphasized on the development of Continuously Regenerating DPF technology which was the best particulate matters removing technology of current existing technology because of its superior comparability and high applicability. This experimental study has been conducted with equipped and unequipped a Continuously Regenerating DPF ona displacement 7,000cc diesel engine and compared in terms of engine performance and emission. To measure the emission, D-13 mode is applied and measured quantities of the exhaust gases, particularly in CO, HC, PM, and NOx. Therefore, this research is focused on engine performance and characteristics on exhaust emissions with the application of a Continuously Regenerating DPF in a heavy-duty diesel vehicle.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.6
• /
• pp.1-7
• /
• 2001

Recently, several LPG engines for heavy-duty vehicles have been developed, which can replace some diesel engines that are one of a main source for air pollution in urban area. As a preliminary study on the liquid phase LPG injection (hereafter LPLI) system applicable to a heavy duty LPG engine, the engine output and combustion performance were investigated with various combustion chambers and fuel compositions using a single cylinder engine equipped. Experimental results revealed that ellipse, double ellipse and nebula type combustion chamber made a more advantage in breaking swirl flow into small turbulence scale than bathtub type. Especially, performance of nebula type showed most highest efficiency and engine output under lean mixture conditions. An investigation fur various LPG fuel compositions was also carried out, and revealed that the case with 40% propane and 60% butane shows the lowest efficiency at stoichiometry, however, as the mixture became leaner its efficiency increased and became even higher for 100% propane case.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.6
• /
• pp.114-118
• /
• 2004

This research focused on the principle and the development of continuous regeneration DPF technology which was the best particulate matters removing technology of current existing technologies owing to its superior comparability and possible applicability. In addition, there were some discussions about the affecting engine parameters such as engine driving conditions and the amounts, velocity, temperature, pressure of exhaust emissions as well as sulfur contents and lubricants which were prerequisites to prevent poisoning effect on catalysts. The test was made on an 8000cc heavy-duty turbo diesel engine on which continuous regeneration DPF was in order to investigate regeneration characteristics of DPF and me performance under the condition of standard or 50ppm low sulphur diesel. Exhaust emissions, CO, HC, NOx PM were measured and compared under D-13 modes.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.5
• /
• pp.213-218
• /
• 1997

CNG dual fuel engine for heavy duty diesel engine has been equipped to a Korean bus engine and tested to compare th engine performance and the emission characteristics with the existing diesel fueled engine. The results are summarized as follows. Diesel fueled engine has the fuel injection timing of BTDC17°. The injection timing of CNG modified engine is retarded to BTDC14° for reduction of NOx. Performance optimization has been carried out to have engine power equivalent to or better than the diesel fueled engine. Smoke is decreased by 85% by Korean smoke 3 mode test. By 6 mode test CO is increased by 313% and THC is increased by 1407%. NOx is decreased by 27%. Even though THC is increased very much, it's not too serious problem since CO and THC emission of diesel engine are very little compared to gasoline engine and THC don't give bad effect on human health. But the reduction technologies of CO and THC need to be considered.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.1
• /
• pp.68-78
• /
• 2006

In the past few years, considerable efforts have been directed towards the further development of Urea-SCR(selective catalytic reduction) technique for diesel-driven vehicle. Although urea possesses considerable advantages over Ammonia$(NH_3)$ in terms of toxicity and handling, its necessary decomposition into Ammonia and carbon dioxide complicates the DeNOx process. Moreover, a mobile SCR system has only a short distance between engine exhaust and the catalyst entrance. Hence, this leads to not enough residence times of urea, and therefore evaporation and thermolysis cannot be completed at the catalyst entrance. This may cause high secondary emissions of Ammonia and isocyanic acid from the reducing agent and also leads to the fact that a considerable section of the catalyst may be misused for the purely thermal steps of water evaporation and thermolysis of urea. Hence the key factor to implementation of SCR technology on automobile is fast thermolysis, good mixing of Ammonia and gas, and reducing Ammonia slip. In this context, this study performs three-dimensional numerical simulation of urea injection of heavy-duty diesel engine under various injection pressure, injector locations and number of injector hole. This study employs Eulerian-Lagrangian approach to consider break-up, evaporation and heat and mass-transfer between droplet and exhaust gas with considering thermolysis and the turbulence dispersion effect of droplet. The SCR-monolith brick has been treated as porous medium. The effect of location and number of hole of urea injector on the uniformity of Ammonia concentration distribution and the amount of water at the entrance of SCR-monolith has been examined in detail under various injection pressures. The present results show useful guidelines for the optimum design of urea injector for reducing Ammonia slip and improving DeNOx performance.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.220.2-220.2
• /
• 2011

Biodiesel and biodiesel blend fuel are receiving increasing attention as alternative fuels for diesel engines without substantial modifications. Biodiesel fuels and blending have been widely studied and applied in diesel engine because of biodiesel's lower sulfur, lower aromatic hydrocarbon and higher oxygen content. Biodiesels have the potential to be oxidized in different condition. It has reported that oxidation deterioration of biodiesel is different in the condition of storage and oxidation causes chemical property change of methyl esters. Sunlight intensity, temperature, material of container and contact surface with oxygen are key dominant factors accelerating oxidation deterioration. In this study, we chose temperature among key oxidation conditions and metal container filled with biodiesel was heated at about $110^{\circ}C$ for 10 days in order to accelerate oxidation deterioration. To better understand the effect of biodiesel blends on emission, steady state tests were conducted on a heavy duty diesel engine. The engine was fueled with Ultra Low Sulphur Diesel(ULSD), a blend of 10% and 20%(BD10, BD20) on volumetric basis, equipped with a common rail direct injection system and turbocharger, lives up to the requirements of EURO 3. The experimental results show that the blend fuel of normal biodiesel with BD10 and BD20 increased NOx. The result of PM was similar to diesel fuel on BD10, but the result of PM on BD20 was increased about 63% more than its of diesel. The blend fuel of Oxidation biodiesel with BD10 and BD20 increased NOx as the results of normal biodiesel. But PM was all increased on BD10 and BD20. Especially THC was extremely increased when test fuel contains biodiesel about 140% more than its of diesel. Through this study, we knew that oxidation deterioration of biodiesel affects emission of diesel engine.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.122-128
• /
• 2000

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.3
• /
• pp.56-63
• /
• 2007

Modern diesel vehicle has to comply with the EURO IV, V regulation with low level of particulate matter and smoke emission Moreover, emission standards of each countries are becoming stringent in advanced countries such as USA and Europe. Because Bio-diesel is similar to diesel fuel, it is essential to judge the environmental and health effects deriving from the use of Bio-diesel in diesel engine. The deterioration characteristics of emission in accordance with aging vehicles must be regulated for Bio-diesel. Therefore, under 1200 driving hours, 220,000km driving distance condition and full load, the deterioration characteristics of emission were estimated. We could reduce sulfur contents of fuel, particulate matter and smoke emission by using Bio-diesel and conform the influence of engine performance, emission, and fuel consumption by Bio-diesel deterioration