• 한국환경보건학회지
• /
• 제8권1호
• /
• pp.31-43
• /
• 1982

Seventy-seven Mugil cephalus of spinal deformation, living in Hanam, Nogsan, and Myeongji area, the downstreams of the Nagdong River, were collected in order to determine their forms and the levels of heavy metal contamination between March and October, 1981. The specimens were examined by X-ray and content of cadmium, lead, copper, and zinc by atomic absorption spectrophotometer. The results were summarized as follows: 1. The rate of appearance of deformational fish to the total Mugil cephflus were 4.3% (13 fish), 5.7% (17 fish), relatively high in May and June (dry season). Meanwhile during March and October they were low by 1.0% (3 fish), 2.0% (6 fish). As far as the research areas are concerned, they appeared in larger numbers in downstreams than in upper streams Myeongji (39), Nogsan (25), and Hanam (13). 2. Concerning with fractured parts of vertebraes,86 percent (66 out of 77) had their caudal regions fractured and 72 percent (55) their first to seventh caudal regions fractured. 3. The average levels of cadmium, lead, copper, zinc detected from flesh were 0.26ppm, 2.06ppm, 6.35ppm, 0.85ppm on the other hand, they were 0.22ppm, 1.84ppm, 5.03ppm, 0.93ppm in normal fish. 4. The average levels of cadmium, lead, copper, zinc measured in the bones were 0.39ppm, 2.55ppm, 8.97ppm, 2.73ppm. Meanwhile, from normal fish they were 0.33ppm, 2.25ppm, 7.24ppm, 2.42ppm. 5. Compared with regional heavy metal contamination such as cadium, lead, zinc, Myeongji area had higher contamination content than Nogsan area Nogsan area than Hanam area. 6. Compared with heavy metal contamination level in their tissues, cadmium was highly found in bones Lead and copper were highly detected in viscera. Particularly in skeleton cadmium was 560 times, zinc 160 times in proportion to those in the downstreams of the Nagdong River.

• Tribology and Lubricants
• /
• 제33권1호
• /
• pp.23-30
• /
• 2017

The electric controlled marine diesel engine has fuel pump generating the high pressurized fuel for fuel injection to combustion chamber via a common rail. Fuel pump consists of a cam-roller system. Journal bearing installed between a roller and a cam-roller pin is subjected to fluctuating heavy and instant loads by cam lift. First, Kinematic analysis is carried out to predict bearing loads during one cycle acting on the journal bearing. Second, flexible multi-body dynamic analysis and transient elasto-hydrodynamic(EHD) lubrication analysis for journal bearing considering elastic deformation of cam-roller pin, roller and bearing are conducted using AVL EXCITE/PU software to predict lubrication performance. The clearance ratio and journal groove shape providing lubrication oil are important parameter in bearing design having good performance and can be changed easier than other design parameters such as diameter, width, oil supply pressure and bearing material grade. Generally, journal bearing performance is represented by the minimum oil film thickness(MOFT) and peak oil film pressure(POFP). As well as the traditional design parameters(MOFT, POFP), in this study, temperature rise of lubrication oil is also evaluated through the side leakage flow of supplied oil. By the evaluating MOFT, POFP and temperature rise, the optimum bearing clearance ratio is decided.

• 한국지반공학회지:지반
• /
• 제12권1호
• /
• pp.35-46
• /
• 1996

강우시의 사면지반과 억지말뚝의 거동을 관찰하기 위하여 각종 계측기에 의한 현장계측이 실시되었다. 즉, 억지말뚝으로 보강된 아파트 배면절개사면에 경사계, 지하수위계 및 스트레인게이지가 설치되었다. 억지말뚝에 발생된 수평변위와 휨응력은 억지말뚝속에 설치된 경사계와 스트레인게이지로 측정하였으며, 사면지반의 수평변형은 말뚝사이지반에 설치된 경사계로 측정하였다. 지하수위 계측결과 강우시 지하수위는 집중호우에 그다지 민감하지 못하였다. 강우시 지표면으로부터 습윤대가 형성되고 이 습윤대의 강하는 말뚝과 지반의 거동에 많은 영향을 미치고 있었다. 왜냐하면 습윤대의 강하로 인하여 이 습윤대 상부지반의 단위체적중량이 증가하게 되고 또한 사면의 활동력이 증가하게 되기 때문이다. 이러한 집중호우시의 억지말뚝과 사면의 거동은 탄성적이었다.

• 한국자동차공학회논문집
• /
• 제18권3호
• /
• pp.133-142
• /
• 2010

The present work focuses on the characterization of material parameters of the Overlay(multilinear hardening) model for analyzing the non-isothermal cyclic deformation. In the previous study, all the parameters were especially based on the Overlay theories, and a simple method was suggested to find out the best material parameters for the isothermal cyclic deformation analysis. Based on the previous research this paper f dther improves the isothermal parameters and suggests how to apply the isothermal parameters to the non-isothermal conditions especially for the description of TMF(Thermo-Mechanical Fatigue) hysteresis behavior. The parameters are determined and calibrated using 400 series stainless steel test data in the reference papers. For the implementation into ABAQUS, a user subroutine is developed by means of ABAQUS/UMAT. The finite element results show good agreement with test for the case of uniaxial non-isothermal cyclic loading, signifying the proposed method can be used in the TMF analysis of the converter-inserted heavy duty muffler system and the stainless steel exhaust-manifold system which are to be done in our future research.

• 제어로봇시스템학회논문지
• /
• 제14권7호
• /
• pp.663-671
• /
• 2008

This paper presents a real-time haptic rendering method for multi-contact interaction with virtual environments. Haptic systems often employ physics-based deformation models such as finite-element models and mass-spring models which demand heavy computational overhead. The haptic system can be designed to have two sampling times, T and JT, for the haptic loop and the graphic loop, respectively. A multi-rate output-estimation with an exponential forgetting factor is proposed to implement real-time haptic rendering for the haptic systems with two sampling rates. The computational burden of the output-estimation increases rapidly as the number of contact points increases. To reduce the computation of the estimation, the multi-rate output-estimation with reduced parameters is developed in this paper. Performance of the new output-estimation with reduced parameters is compared with the original output-estimation with full parameters and an exponential forgetting factor. Estimated outputs are computed from the estimated input-output model at a high rate, and trace the analytical outputs computed from the deformation model. The performance is demonstrated by simulation with a linear tensor-mass model.

• 소성∙가공
• /
• 제19권6호
• /
• pp.329-336
• /
• 2010

Ring forging process is more appropriate for high-length and thin walled ring, because it utilizes the forging press and hence does not require heavy-duty ring rolling mill. Although ring forging process is very simple and economic for facilities, the process is not efficient because of multi-forging-step and low material utilization. An effective ring forging process is developed using a hollow ingot. When a hollow ingot is used with a workpiece, the ingot can be forged into a final ring without multi-stage pre-forging process, such as, cogging, upsetting, and piercing, etc.. Finally it has advantages of the material utilization and process improvement because a few reheating and forging process are not necessary to make workpiece for ring forging. The important design variables are the applied plastic deformation energy to eliminate cast structure and make uniform properties. In this study, the mechanical properties after forging of hollow cast ingot were investigated from the experiment using circumferential sectional model. Also, the effects of process variables were studied by FEM simulation on the basis of thermo-visco-plastic constitutive equation. Applied strain is different at each position in length direction because diameter of hollow ingot is different in length direction. The different strain distribution become into a narrow gap by additional plastic deformation during diameter extension process.

• 한국기계가공학회지
• /
• 제15권2호
• /
• pp.84-88
• /
• 2016

This study evaluated the structural safety of a heavy-duty integrated machine for grinding wheel forming. Structural analysis was performed to evaluate the structural safety of the base. The base was designed by dividing the single base and detachable base. The analysis conditions were applied to the own weight and the load of component parts. From the structural analysis results, although the stress of the detachable base was decreased, the amount of deformation was increased. If the deformation of the detachable base decreases, it is expected to be safer than the single base.

• 대한조선학회논문집
• /
• 제45권6호
• /
• pp.703-709
• /
• 2008

In the shipyard, line heating and triangle heating are two major processes for forming curved plates in various shapes. While there have been many studies on line heating, triangle heating has been rarely studied due to its complicated heating process with irregular multi-heating paths and highly concentrated heat input. As the triangle heating process is one of the most labor-consuming jobs in shipyards, it is essential to study the automation as well as improvement of triangle heating process in order to increase hull forming productivity. In this study, a pioneering attempt to simulate triangle heating was made. A circular disk-spring model was proposed for elasto-plastic analysis procedure of triangle heating and the inherent strain method was also used to analyze the deformation of plates. Simulation results were compared with those of experiments and showed good agreement. It is shown that the present approach including analysis model used in this study is effective to simulate the triangle heating for plate forming process in shipbuilding.

• 한국해양공학회지
• /
• 제30권2호
• /
• pp.117-124
• /
• 2016

A C-type LNG mock-up tank was constructed to evaluate the durability of the tank and its structural safety. An experimental strain analysis system equipped with strain gages was designed to investigate the structural behavior of the inner tank at a high hydraulic pressure. In addition, the insulation used in the space between the inner tank and outer tank had a compressive strength and the inner tank thickness of the cylindrical shell and hemisphere was 4.0 mm, which was designed to be thinner than the existing rules. The strains on the inner tank were measured with increasing pressure, and these measurements were compared and analyzed at the strain gage attachment points.

• Journal of Mechanical Science and Technology
• /
• 제14권6호
• /
• pp.633-644
• /
• 2000

Recently, in proportion to the increase of earthquake occurrence-frequency and its strength in the countries within the circum-pan Pacific earthquake belt, a concept of earthquake-proof design for huge structures containing liquid has been growing up. This study deals with the refinement of classical numerical approaches for the free vibration analysis of separated structure and liquid motions. According to the liquid-structure interaction, LNG-storage tanks exhibit two distinguished eigenmodes, the sloshing mode and the bulging mode. For the sloshing -mode analysis, we refine the classical rigid-tank model by reflecting the container flexibility. While, for the bulging-mode analysis, we refine the classical uncoupled structural vibration system by taking the liquid free-surface fluctuation into consideration. We first construct the refined dynamic models for both problems, and present the refined numerical procedures. Furthermore, in order for the efficient treatment of large-scale matrices, we employ the Lanczos iteration scheme and the frontal-solver for our test FEM program. With the developed program we carry out numerical experiments illustrating the theoretical results.