• KSBB Journal
• /
• v.23 no.4
• /
• pp.335-339
• /
• 2008

Biodiesel is an alternative and renewable energy source, which is hoped to reduce global dependence on petroleum and environmental problem. Biodiesel produced from a variety of oil sources such as vegetable oil, animal fat and waste oils, and has properties similar to those associated with petro-diesel, including cetane number, volumetric heating value, flash point, viscosity and so on. In this study, we investigate the effect of quality of raw materials on alkali-catalyzed transesterification for producing of biodiesel. The increase of content of free fatty acid and water in oil were caused the sharp decrease of conversion yield. Also, the low purity of methanol in reactant was inhibited the reaction rate. In the case of addition of sodium sulfate as absorbent to prepare catalyst solution, the content of fatty acid methyl ester in product was increased more about 1.6% than that of control. However, the addition of zeolite, sodium chloride and sodium sulfate as absorbent in reactant to remove water generated from reaction did not show any enhancement in the reaction yield. This result may provide useful information with regard to the choice and preparation of raw materials for more economic and efficient biodiesel production.

• Journal of Ginseng Research
• /
• v.22 no.4
• /
• pp.304-309
• /
• 1998

Incubation condition affecting the chlamydospore formation and isolation from mycelia and conidia of Cylindrocarpon destructanse (isolate ACY-9701), isolated from the root rot lesion of the American ginseng (Panax quinquefolium) was investigated. Chlamydospores were formed from mycilia but not from conidia on the Czapek-Dox agar without carbon or nitrogen source after 20 days incubation at 2$0^{\circ}C$. In the medium added with nitrogen and carbon sources, immatured chlamy-dospore-like cells were formed from microconidia and mycelia as well. Immatured chlamydospore-like cells were formed from mycelia as well as microconidia In corn, kidney bean, and pea root extracts after 20 days incubation at 20"C, while typical chlamydospores were formed from both of them in the root extract of Panax quinquefolium. The 3.6 log chlamydospore/mm" was converted from microconidia in the medium, which was equal to 2.5% conidia formed. Under the light condition (251.1 pmol/m" sec, 12 hrs dark and light cycle), 4.2 log/mm" of chlamydospores were converted from interracially or terminal cells of macroconidia, which was 4.0% of macroconidia produced on Potato dextrose agar (PDA). When mycelia and microconidia were stored at -7$0^{\circ}C$ for 32 days and incubated on PDA after thawing at room temperature to isolate chlamydospores from them, microconidia and mycelia were still alive. Meanwhile, microconidial lysis was found after heating them at 32$^{\circ}C$ for 7 days, but the chlamydospores converted from macroconidia were not lysed up to 13 days at 32"C. to 13 days at 32"C.ot;C.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.1
• /
• pp.271-279
• /
• 2015

Induction cooking application with multiple loads need high power inverters and appropriate control techniques. This paper proposes an inverter configuration with buck-boost converter for multiple load induction cooking application with independent control of each load. It uses one half-bridge for each load. For a given dc supply of $V_{DC}$, one more $V_{DC}$ is derived using buck-boost converter giving $2V_{DC}$ as the input to each half-bridge inverter. Series resonant loads are connected between the centre point of $2V_{DC}$ and each half-bridge. The output voltage across each load is like that of a full-bridge inverter. In the proposed configuration, half of the output power is supplied to each load directly from the source and remaining half of the output power is supplied to each load through buck-boost converter. With buck-boost converter, each half-bridge inverter output power is increased to a full-bridge inverter output power level. Each half-bridge is operated with constant and same switching frequency with asymmetrical duty cycle (ADC) control technique. By ADC, output power of each load is independently controlled. This configuration also offers reduced component count. The proposed inverter configuration is simulated and experimentally verified with two loads. Simulation and experimental results are in good agreement. This configuration can be extended to multiple loads.

• Journal of Korean Society of Forest Science
• /
• v.99 no.5
• /
• pp.706-710
• /
• 2010

Understanding of chemical composition and energy contents in tree is important to develope strategies of renewable energy policy to cope with climate change. Residual biomass as renewable energy source was evaluated and focused on the bark-containing branches. Chemical analysis studies were conducted for different part of yellow poplar (Liriodendron tulipifera), which were partitioned to inner bark, outer bark, small branches, medium branches, big branches and trunk. The variations in hydrophobic extractives, hydrophilic extractives, lignin, carbohydrate compositions, energy contents (higher heating value) and the ash content were determined. The inner and outer bark had higher ash content, hydrophobic and hydrophilic extractives content, and higher energy content than those of tree trunk. Polysaccharides content in inner and outer bark was quite lower than those of stem or branches. Based on the energy content of residual biomass, replacement of fossil fuel and greenhouse gas emission abatement were calculated.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2441-2444
• /
• 2003

This paper describes fabrication of a micro cell counter integrated with an oxygen micropump and Sephadex G-25 beads counting experiment. The device utilized a phototransistor, microwindow, and light source of microscope for beads detection. Microheater and microchannel were used for pumping and guiding of beads to the microwindow. Counting capability of the device was tested with a peristaltic pump and the measured signals (${\sim}10\;mV$) with oscilloscope showed peak shape when beads passed the microwindow. Pumping of beads by the oxygen micropump was carried out by heating paraffin, which enveloped manganese dioxide (catalyst), to trigger the decomposition of hydrogen peroxide into water and oxygen. It lasted for 5 min with $7\;{\mu}l$ of wt. 30 % hydrogen peroxide. Beads counting by oxygen micropump showed peaks ($2{\sim}20\;mV$) with $30\;{\mu}l$ of beads sample and the number of peaks by magnitude was acquired.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.11
• /
• pp.1060-1066
• /
• 2007

When a high-energy ultrasound propagates through a solid body that contains a crack or a delamination, the two faces of the defect do not ordinarily vibrate in unison, and dissipative phenomena such as friction, rubbing and clapping between the faces will convert some of the vibrational energy to heat. By combining this heating effect with infrared imaging, one can detect a subsurface defect in material efficiently. In this paper a detection of the welding defect of thin SUS 304 plates using the UIR (ultrasonic infrared imaging) technology is described. A low frequency (20kHz) ultrasonic transducer was used to infuse the welded thin SUS 304 plates with a short pulse of sound for 280ms. The ultrasonic source has a maximum power of 2kW. The surface temperature of the area under inspection is imaged by a thermal infrared camera that is coupled to a fast frame grabber in a computer. The hot spots, which are a small area around the defect tip and heated up highly, are observed. From the sequence of the thermosonic images, the location of defective or inhomogeneous regions in the welded thin SUS 304 plates can be detected easily.

• Clean Technology
• /
• v.12 no.2
• /
• pp.78-86
• /
• 2006

Computational analyses are conducted on the combustion characteristics of the coal- and the biomass-derived synthetic gases with low-Btu heating value in gas engine. Using thermochemical analyses on the synthetic gases, combustion pressure, temperature, exhaust gas composition, NO emission and engine power are predicted and the predicted results are compared with small-scale pilot engine test results. In order to investigate the unsteady combustion phenomena in gas engine combustion chamber, CFD analyses are carried out on the coal and the biomass synthetic gases and their computed results are compared to provide the guidelines for the design modification and the tuning of the gas engine burning the synthetic gases as alternative fuels.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.2 s.245
• /
• pp.177-185
• /
• 2006

This study aims deriving analysis the flow characteristic of kitchen hood system with using 3-D numerical analysis method and improving the system to expel pollutes more efficiently. To understand the flow characteristics of four models, this study only focuses on velocity field, temperature field, and concentration field varying with followings whether separation plate is set or not and the shapes of separation plates. The quantity of air, speed of exhaust fan and temperature and concentration of heating source are concerned as constant values. The three models having different shapes have one exhaust port and the model which has the vent at the closest position to where pollutes are generated is discovered to be the most efficient model. Compare to the initial model (having no separation plate), it was $1.4-1.9\%$ more efficient at temperature distribution and $9.4-11.9\%$ more at $CO_2$ concentration distribution.

• Proceedings of the KIEE Conference
• /
• 2003.10b
• /
• pp.216-219
• /
• 2003

The resonant inverter is widely used for induction heating, electronic ballast and supersonic motor driving circuit. In the meantime, control techniques of PWM, PFM etc.. are mainly applied to control the output power of the resonant inverter. But, in the case of using the half bridge resonant inverter, it is difficult to control the output power by PWM, because its main circuit does not provide the load free-wheeling mode. Therefore, PAM or PFM was usually applied to control output power of half bridge resonant inverter. However, PAM needs a variable DC voltage source, which makes the system structure more complex. On the other hand, in case of PFM, efficiency is declined by operation with poor power factor. This paper Proposed the novel half bridge resonant inverter which can provide the load free-wheeling mode. Also its analysis results for PWM operation with unity fundamental power factor are Presented and compared with other resonant inverters using PWM and PFM.

• Proceedings of the KIPE Conference
• /
• 2003.07a
• /
• pp.27-30
• /
• 2003

This paper describes two novel current fed high frequency resonant inverter can be used as the power supp]y for wax-sealing. This two topology can be obtained higher output frequency than switching frequency by composing modified unit inverter based on conventional half-bridge serial resonant inverter in parallel with input power source. also, By using time-sharing gate control method, this proposed inverter can not only realize the output control of dependence irrespective of the switching frequency using phase-shift but also reduce switching loss because it has ZVS function. Simulation results through the Pspice have demonstrated the feasibility of the proposed inverter. This proposed inverter will be able to be practically used as a power supply in various fields as induction heating applications, DC-DC converter etc.