• Elastomers and Composites
• /
• 제51권4호
• /
• pp.280-285
• /
• 2016

The purpose of this study is to get optimum design and operation conditions of the heating rubber roller for laminating process. The cause of performance degradation of heating rubber roller is delamination of rubber on metal tube, rubber aging due to high temperature. We measured the material properties of thermal expansion, thermal conductivity, specific heat and density and analyzed thermal distributions of rubber layer using finite element method. As a result of heat/flow analysis, the density distribution of heating coil must shorten the stabilization time by reducing the temperature deviation on the length direction at the temperature rising section after increasing the density of the area contacting with the laminate film at the center part which is an opposite of the current composition while enabling to maintain the temperature of heater to be consistent while maintaining the temperature deviation to be low when heat loss is created. Finally, we determined optimum heating method of heating rubber roller.

• 한국정밀공학회지
• /
• 제22권7호
• /
• pp.155-163
• /
• 2005

Pressure heating rollers with temperature control were mounted to a flat cable laminating machine (FCLM). Pressure heating rollers should be heated up to the setting temperature $(175^{\circ}C)$ and kept on to producing good quality flexible flat cables (FFC). Existing Pressure heating rollers took more than 70minutes to the setting temperature and did not keep on the setting temperature in production. Temperature controller, electric power controller, material and diameter of rollers and heat capacities were changed to improve the temperature control of the pressure heat rollers for better production of the FFC. Thus, the reaching time to the setting temperature (RT), temperature stability time (TST) and temperature hunting (TH) were measured and compared with the existing pressure rollers case. The RT of A roller was shortened by 50minutes, and B roller was shortened by 15minutes. The TST of A roller was shortened by 13minutes, and B roller was shortened by 15minutes. The THs of both A and B rollers were settled up to ${\pm}5^{\circ}C$. Finally, the productivity of the FCLM and the quality of the FFC were increased.

• 한국기계가공학회지
• /
• 제21권1호
• /
• pp.28-33
• /
• 2022

The heating roller of an actual pulse output device (POD) production facility is composed of a steel roller and a rubber roller. The time to reach a specific temperature and the temperature distribution on the roller surface were analyzed and compared according to the change in the number of cartridge heaters inside the heating roller. In this analysis, a steady-state thermal analysis of a steel roller was performed for the cases of a 5-cartridge heater and 9-cartridge heater. Finite element analysis was applied with reference to the surface temperature data of the heating roller during operation and the calorific value of the cartridge heater. Using the 9-cartridge heater, faster target temperature achievement and more uniform temperature distribution were confirmed than for the 5-cartridge heater.

• 한국전기전자재료학회논문지
• /
• 제30권10호
• /
• pp.677-682
• /
• 2017

Lamination is used extensively in various industries. The type of lamination applied to the material depends on the precision level required, which varies for materials needed for everyday use, materials used in high-tech industries, and processes employed to fabricate finished products. Especially in hot lamination, the distribution of the surface temperature of the heating roller is very important to avoid the generation of internal bubbles and ensure flatness of the attached materials, and thus maintain a good standard of quality and productivity. In this study, we have developed a system to monitor the surface temperature of the heating rollerby applying a heterogeneous controller and a non - contact temperature sensor. This monitoring system accurately measures the surface temperature of the heating roller and applies the RS485 MODBUS communication method for easy expansion. Using this system, a laminated prototype was fabricated, and its efficacy for non-contact temperature sensor calibration, Ethernet IP communication, stoppage of the heating roller, and determination of temperature distribution with rotation was examined for its potential usage in industries.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.538-543
• /
• 2008

A roller with a shaft and hot oil paths for pressing electrodes of polymer batteries were modeled and analyzed by FEM. There are many hot oil tubes in the roller and shaft, through which $72^{\circ}C$ hot oil flows for heating the surface of a roller and shaft. Thermal deformations and temperatures distributions of the roller and shaft were calculated and a convection boundary condition on surfaces was used. The influence of existence of a groove in the shaft on the flatness of a roller surface caused by thermal deformation was investigated. In addition, the amount of spring-back of electrodes under vacuum pressure and heating was calculated after the hot rolling process. It was shown from this study that the groove in one shaft had a favorable effect on the surface flatness.

• 대한조선학회논문집
• /
• 제36권3호
• /
• pp.134-143
• /
• 1999

선박의 선미부와 선수부는 복잡한 곡을 가진 블록들의 조립으로 만들어진다. 이러한 복잡한 곡률 분포를 가진 이중 곡면을 성형하기 위해서 조선소에서는 롤러 굽힘 가공과 선상 가열을 이용하고 있다. 일차적으로는 롤러 굽힘에 의한 가공으로 실린더 형상이나 원추 형상의 곡면을 만들고 난 후, 선상 가열을 수행하여 목적 형상으로 이차 가공을 한다. 본 논문은 곡면 가공에서 선행되는 일차 가공의 정보로서 가공 방향과 가공 후 형상을 결정하는데 목적이 있다. 목적 형상의 가우스 변환(Gauss mapping)으로부터 가공 방향에 관한 정보를 결정하고 목적 형상과 롤러 굽힘 가공에 의해 변형된 판 사이의 기하학적 관계를 이용하여 롤러 굽힘 가공의 모양을 결정하는 알고리즘을 제시하였다.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2008년도 춘계학술발표대회 논문집
• /
• pp.148-153
• /
• 2008

An inflow of daylight to the room offers comfortable view environment, psychological and physical security to people in the room and there are merits such as a work efficiency and energy saving. But, it has many problems as an excessive direct sunlight, cooling and heating. We can expect to have energy saving effect for illumination with comfortable view environment creation through control on height of roller shade. This study will be a used a fundamental approach to control on height of roller shade to changing daylight.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 Proceedings ICPE 01 2001 International Conference on Power Electronics
• /
• pp.75-79
• /
• 2001

This paper presents a novel version of an active voltage clamped ZVS-PWM high frequency inverter using IGBTs for electromagnetic induction eddy current-based rolling drum heating in new generation copy and printing machines in consumer business use. The operating principle of this inverter circuit and unique features are described herein. Its constant frequency duty cycle (asymmetrical PWM) controlled voltage source quasi-resonant soft switching high frequency inverter employing IGBTs is proposed, which is capable of achieving stable and efficient zero voltage soft switching commutation over a widely specified power regulation range from full power to low power. The operating performances in a steady state of this inverter is discussed and evaluated on basis of simulation and experimental results as an induction heated roller in new generation copy machine.

• Journal of Power Electronics
• /
• 제6권2호
• /
• pp.178-185
• /
• 2006

Recently, the demand for the development of high quality and high-speed laser printers and efficient power utilization has required. Among complicated electro-mechanic devices in laser printers, the toner-fusing unit consumes above 90[%] of all electrical energy needed for printing devices. Therefore, the development of a more effective energy-saving toner fusing process becomes a significant task in great demand. Generally, there are several ways to implement a fusing unit. Among them this paper presents a new induction heating method. The proposed induction heating method enables the increase of coupling coefficient between heating coil and heat roller which also increases total energy transfer efficiency. Therefore, the proposed IH (Induction Heating) inverter system provides very fast W.U.T. (Warm UP Time) as well as higher efficiency. Through experimental results, the proposed control system is verified.

• Journal of Advanced Marine Engineering and Technology
• /
• 제36권2호
• /
• pp.276-285
• /
• 2012

본 연구목적은 열간압연용 런-아웃 테이블 롤러 표면의 기계적 성질을 개선하기 위해 다공질 자용성 합금으로 피복하는 방법을 개발하는 것이다. 열간압연에서 런-아웃 테이블의 롤러 내구성을 높이기 위해서는 고온에서 롤러표면의 경도를 높게 유지해야 하고, 내마모성, 내식성, 내열성, 내소부성 및 내응착성의 향상을 유지하여야 한다. 또한, 고온의 열연 강판을 안정적으로 이송할 수 있도록 하기 위해서는 롤러표면에 적절한 마찰계수를 유지하도록 하여야 하고, 롤러와 강판 사이에 미끄럼 발생이 없어야 한다. 본 연구에서는 자용성 합금에 텅스텐카바이드를 첨가시켜 서메트화하여 롤러의 내마모성을 증대시켰고, 미세 철분말을 롤러표면에 피복하여 다공질을 만들어 마찰계수를 높이고 붙잡음성을 향상시켰다. 그 결과, Ni-Cr 피복 롤러에 비하여 다공질 자용성 합금 피복 롤러는 피복층에 철분이 5 ~ 10 wt%로 많이 함유되어 재용융 공정에서 전기로로 가열하여 일부분만 합금화되고 나머지는 산화 및 용해에 의해 탈락되어 다공질로 나타나 강판과의 붙잡음성을 향상시켰다.