• 한국지구물리탐사학회:학술대회논문집
• /
• 한국지구물리탐사학회 2003년도 Proceedings of the international symposium on the fusion technology
• /
• pp.695-702
• /
• 2003

In this study, an experimental apparatus has been designed and set-up to analyse the dissociating phenomena of hydrate in porous rock using electric heating method supplied at downhole. The electric heat injecting experiments have been performed to investigate the heat transfer within the core, the dissociating phenomena of hydrate, and the productivities of dissociated gas and water. These experiments were under constant heat injecting method as well as preheating methods. From the experimental results, it is seen that the hydrates is dissociated along the phase equilibrium curve and dissociation of hydrate is accelerated with heat. The injected heat is consumed for the dissociation and also it is lost together with outflow of the dissociated gas and water. From the investigation of gas producing behavior for various heat injecting methods, as the injected heat is greater, dissociation is accelerated faster at outlet and hence the initial gas production becomes higher. Also, it is shown that the initial gas productivity under the constant heating method is better, however, the energy efficiency is low because of smaller amount of the produced gas comparing to the amount of heat injected. In the experiments of preheating method, it was seen that gas production only initial stage is different with the preheating time, but the producing behaviors of gas production are similar.

• Journal of the Korean Recycled Construction Resources Institute
• /
• 제7권3호
• /
• pp.85-90
• /
• 2012

In this study, temperature profile of the fly ash concrete were studied in accordance with the change of heating curing method combination for the slab concrete in order to develop efficient protection method of the concrete subjected to $-20^{\circ}C$. The slab concretes with the size of $1200mm{\times}600mm{\times}200mm$ were fabricated with W/B of 50% and exposed to $-20^{\circ}C$ for 7 days. Five different combinations of heat curing methods were applied to the slab concrete specimen; two combinations of heat supplying by electrical heater and surface heat insulation material such as polyethylene film and quadrupled layer bubble sheet based on heat enclosure installment; three combinations of heating coil embedment and surface heat insulation materials such as polyethylene film, sawdust and quadrupled layer bubble sheet based on heat enclosure installment. Test results showed that by applying both heating coil and bubble sheet and heat enclosure, the concrete exposed to $-20^{\circ}C$ can be effectively protected from early-age frost damage.

• Journal of the Korean housing association
• /
• 제6권1호
• /
• pp.31-37
• /
• 1995

The purpose of this study is to analyse the distribution of thermal sensation response and thermal environment condition in convective heating space. The contents of this study are as follows: 1)the spatial distributions of thermal conditions are measured 2)the thermal sensation vote of residents is taken in order to investigate the relation between thermal condition and human thermal sensation in sedentary condition 3)to analyse the distribution of subject's thermal sensation vote and thermal environment condition by two methods-regression method and graph method.

• Korean journal of food and cookery science
• /
• 제12권1호
• /
• pp.40-45
• /
• 1996

This study was conducted in order to determine the effect of various cooking methods (boiling, pressure cooking, steaming and microwave heating) on mineral content, color and sensory quality of radish, potato and carrot. It was shown that microwave heating was desirable method in cooking radish on both the acceptability and the retention of mineral content. On the other hand, steaming and pressure cooking were found to be desirable methods for cooking potato. There were not so many differences in both the retention of mineral content and the acceptability of carrot by various cooking methods. The pressure cooking, which was not a proper method for leaf vegetables, could be applied to root vegetables without losing so many mineral contents.

• The Journal of the Korea institute of electronic communication sciences
• /
• 제5권6호
• /
• pp.645-650
• /
• 2010

In this research, the problem of combustion and its system in Hyundai Heavy Industries and Sachuan Unison will be analyzed in order to provide some methods of thermal efficiency improvement and help to make a positive influence on fuel savings and their productivity. In forging industries, in order to improve the material properties of the industrial heating elements which are being used, depending on different operation conditions of system equipment and combustion systems, fuel consumption and material properties can get a profound influence. Thus, analyzing about combustion system characteristics of 100 tons heating furnace and heat treatment furnace which are in operation in Hyundai Heavy Industry will be done. In usual, air-fuel ratio is proper for capacity of burner installed in each heating device, otherwise burner gets an automatic turn down ratio. It has a profound influence on heating performance and precision of temperature because it is the fixed characteristics of every industrial furnace. Even if there are some methods to improve the heating performance of a furnace installed with a large capacity burner, it is very difficult to obtain the precision of temperature in maintenance interval. Based on this, performance of burner can be drove to best by improving combustion system. Proper Combustion characteristic for each heating interval was analyzed in heating furnace in Hyundai Heavy Industry. A project plan for improving fuel savings and increasing precision of temperature was presented in this research.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.183-186
• /
• 2007

The injection molding process has high accuracy and good reproducibility that are essential for mass production at low cost. Conventional molding processes typically use the water-based mold heating and air cooling methods. However, in the nano injection molding processes, this semi-active mold temperature control results in the several defects such as air-flow mark, non-fill, sticking and tearing, etc. Therefore, in order to control temperature of the molds actively and improve the quality of the molded products, the novel nano injection molding system, which uses active heating and cooling method, has been introduced. By using the Peltier devices, the temperature of locally adiabatic molds can be controlled dramatically and the quality of the molded patterns can be improved.

• Transactions of the Society of Information Storage Systems
• /
• 제3권3호
• /
• pp.149-153
• /
• 2007

Perpendicular patterned magnetic media have been regarded as a prime candidate to achieve an ultra-high magnetic recording density of over 1 Tera-bits/$inch^2$. Patterned magnetic media with nanoscale patterns have been fabricated using various nanopatterning technologies. We focused on the two technical issues of nanoinjection molding technology. Firstly, we have investigated a cost-effective method to fabricate metallic stamps. Secondly, we focused on the analysis of nanoinjection molding with passive heating, where the replication of 50 nm nanopillar arrays was successful. The effect of the thermal insulation layer on the replication quality was examined by analytical and experimental methods. Finally, we deposited a magnetic layer on a injection molded nanopillars and measured. Our methodology can provide cost-effective mass-production for patterned magnetic media.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• 제15권12호
• /
• pp.1035-1042
• /
• 2003

As the desire for a better condition in classroom increases, the distribution rate of warming and cooling conditioners increases. But it is known that according to the way by which the equipments put and are operated the comfortableness felt by persons who are in classroom can make a difference. Therefore, proper equipments in accordance with the size of classroom should be considered as well as operational methods when ceiling warming and cooling conditioners put. This study makes conclusions as follows through a simulation to get improvements in accordance with the size of classroom and to improve the heating performance of ceiling warming and cooling conditioners in classroom.

• Proceedings of the Korean Society for Bio-Environment Control Conference
• /
• 한국생물환경조절학회 1998년도 임시총회 및 학술논문발표요지
• /
• pp.11-18
• /
• 1998

우리나라의 산업구조는 1970년 이후에 에너지 과다 소비형인 중공업, 석유화학 공업, 제철공업, 조선, 자동차 등이 집중 육성되었다. 그 결과로 지구 온난화의 주범인 $CO_2$는 1990년-2000년 사이에 128%의 증가(세계 1위)가 예상되어 세계 2위인 스페인에 비하여 무려 5배나 $CO_2$ 발생량을 많이 배출하고 있다. 1997년 제 3차 세계기후협약 이후에 선진국들은 한국을 강력히 규제할 것으로 보여진다. (중략)

• Journal of Welding and Joining
• /
• 제8권1호
• /
• pp.43-53
• /
• 1990

The transient temperature distribution in the continuous friction welding 304 stainless steel bars is investigated by experimental and analytical methods. It is calculated by F.D.M. (finite difference method). The heating pressure, the rotational speed and friction coefficient obtained from experiment are used to determine the heat input at the contacting surface. Thermal properties of the workpiece are the function of temperature. The calculated temperature is well coincided with the measured value. The grain size at weld interface is extremely small due to the severe plastic deformation at high temperature, and result of this refined zone reveals higher hardness value. Because the HAZ is very narror about 2-3 mm, welding defects do not occure.