• Korean Journal of Materials Research
• /
• v.19 no.6
• /
• pp.305-312
• /
• 2009

The effects of Quenching and Partitioning (Q&P) and Annealed Martensite (AM) heat treatment on the microstructure and tensile properties were investigated for 0.24C-0.5Si-1.5Mn-1Al steels. The Q&P steels were annealed at a single phase ($\gamma$) or a dual phase (${\gamma}+{\alpha}$), followed by quenching to a temperature between $M_s$ and $M_f$. Then, enriching carbon was conducted to stabilize the austenite through the partitioning, followed by water quenching. The AM steels were intercritically annealed at a dual phase (${\gamma}+{\alpha}$) temperature and austempered at $M_s$ and $M_s{\pm}50^{\circ}C$, followed by cooling in oil quenching. The dual phase Q&P steels showed lower tensile strength and yieldyield strength than those of the single phase Q&P steels, and tThe elongation for the dual phase Q&P steel was partitioning 100s higher than that of that for the single phase Q&P steels as the partitioning time was less than 100s up to partitioning 100s. For AM steels, the tensile/yield strength decreased and the total elongation increased as the austempering temperature increased. The stability of the retained austenite controlled the elongation for Q&P steels and the volume fraction of the retained austenite controlled the elongation for AM steels.

• Journal of Oriental Physiology
• /
• v.14 no.2 s.20
• /
• pp.99-116
• /
• 1999

This study was undertaken to define the expression rule of six vital substances for human life(六氣) in Meridians and the rule of following of three ${\breve{U}}m$ and three Yan. In order to investigate the expression rule of six vital substances for human life(六氣), incident(標)-fundamental(本) and Ki of middle energizer(中氣) of three ${\breve{U}}m$ and three Yang(三陰三陽) were reviewed. 1, The rule of following is formed centering around fundamental Ki(本氣) between incident(標) and fundamental(本). And in case the ${\breve{U}}m$ and Yang (陰陽) disposition of incident(標) and fundamental(本) is different, whether the ${\breve{U}}m$ and Yang(陰陽) disposition of incident(標) and fundamental(本) is same as those of Ki of middle energizer(中氣), is the key point in following fundamental and activating of the vital energy(氣化). 2. As twelve channels(十二經脈) have not only fundamental Ki(本氣) but also Ki of middle energizer(中氣) at the same time, in expression of six vital substances for human life(六氣), if the fundamental Ki(本氣) is stronger, fundamental Ki(本氣) can be expressed or if the fundamental Ki(本氣) is weaker, Ki of middle energizer(中氣) can be expressed. 3. Twelve channels which is connected with each other through the relation of the interior and the exterior can be regarded as a system, in which Wind(風) and Fire(火), Dryness(燥) and Dampness(濕), Cold(寒) and Heat(熱) maintain balance through mutual control. 4. We can see that in the disease caused by the unbalance of six vital substances for human life(六氣), expression of six pathogenic factor and controlment of six vital substances for human life(六氣) are made up after the following one in the rule of following(從化規律).

• Parasites, Hosts and Diseases
• /
• v.31 no.4
• /
• pp.379-381
• /
• 1993

We experienced the partial Inhibition of entry of Taxoplasma gondii Into MDCK cells when the FBS was depleted from media. MDCK cells and Toxoplasma (RH strains) were co-cultured, the penetration was inhibited up to 60-80% with concentration-dependence of FBS. Inhibitory effect was clear when the conc. of FBS was over 1% (v/v) with 50% inhibition comic. of 5%. When ToxopLosma was pre-incubated with FBS and then applied to MDCK cells, there were no inhibitory effect, but when FBS was added to Toxoplasma- MDCK co-culture, the time of adding was c10cal with rapid inhibition. And when FBS was further treated with heat ($95^{\circ}C$, 10 min), the Inhibitory effect was decreased slightiy in both raw and inactivated FBS. The FBS factor(s) might participate to neutralize secreted materials which enhancing penetration or Intervene between receptor-ligand blnding at the moment of entry through sterically rather than functionally.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.465-469
• /
• 2006

Two mesophilic trickling bed bioreactors filled with two different types of media, hydrophilic- and hydrophobic-cubes, were designed and tested for hydrogen production via anaerobic fermentation of sucrose. Each reactor consisted of a column packed with polymeric cubes and inoculated with heat-treated sludge obtained from anaerobic digestion tank. A defined medium containing sucrose was fed with changing flow rate into the capped reactor, hydraulic retention time and recycle rate. Hydrogen concentrations in gas-phase were constant, averaging 40% for all conditions tested. Hydrogen production rates increased up to $10.5 L{\cdot};h^{-1}{\cdot}L^{-1}$ of reactor when influent sucrose concentrations and recycle rates were varied. Hydrophobic media provided higher value of hydrogen production rate than hydrophilic media at the same operation conditions. No methane was detected when the reactor was under a normal operation. The major fermentation by-products in the liquid effluent of the both trickling biofilters were acetate and butyrate. The reactor filled with hydrophilic media became clogged with biomass and bio gas, requiring manual cleaning of the system, while no clogging occurred in the reactor with hydrophobic media. In order to make long-term operation of the reactor filled with hydrophilic media feasible, biofilm accumulation inside the media in the reactor with hydrophilic media and biogas produced from the reactor will need to be controlled through some process such as periodical backwashing or gas-purging. These tests using trickling bed biofilter with hydrophobic media demonstrate the feasibility of the process to produce hydrogen gas in a trickle-bed type of reactor. A likely application of this reactor technology could be hydrogen gas recovery from pre-treatment of high carbohydrate-containing wastewaters.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.32 no.5
• /
• pp.545-550
• /
• 2012

Steam generator is one of the major components of nuclear power plant and steam generator tubes are the pressure boundary between primary and secondary side, which makes them critical for nuclear safety. As the operating time of nuclear power plant increases, not only damage mechanisms but also scaled deposits on steam generator tubes are known to be problematic causing tube support flow hole blockage and heat fouling. The ability to assess the extent and location of scaled deposits on tubes became essential for management and maintenance of steam generator and eddy current bobbin data can be utilized to measure thickness of scale on tubes. In this paper, tube reference standards with various thickness of scaled deposit has been set up to provide information about the overall deposit condition of steam generator tubes, providing essential tool for steam generator management and maintenance to predict and prevent future damages. Also, methodology to automatically measure scale thickness on tubes has been developed and applied to field data to estimate overall scale amount.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.5
• /
• pp.403-410
• /
• 2007

In this study, natural refrigerants and their mixtures that can supplement and replace R12 and R134a in automobile air-conditioners are studied. R134a is currently used as the refrigerant in new motor vehicle air conditioners, replacing the ozone depleting refrigerant R12. Although R134a has no ozone depletion potential, it has a relatively large global warming potential, approximately 1300 times that of $CO_2$ over a 100 year time horizon. For this reason, performance of natural refrigerants and their mixtures containing R152a, RE170 (Dimethylether, DME) and R600a (Isobutane) are measured under 2 different temperature conditions. They were tested in a refrigerating bench tester with an open type compressor. The test bench provided about 4 kW capacity and water and water/glycol mixture were employed as the secondary heat transfer fluids. Test results show that the coefficient of performance (COP) of these refrigerants is up to 21.55% higher than that of R12 in all temperature conditions. Overall, these fluids provide good performance with reasonable energy savings without any environmental problem and thus can be used as long term alternatives for automobile air-conditioners.

• Elastomers and Composites
• /
• v.15 no.3
• /
• pp.147-154
• /
• 1980

The cellular rubber products for industrial purpose have been applied in many fields such as auto-motive parts, ship-building, machinery, sports goods, diving suit or interior housings etc. The purpose of this dissertation is to study the physical properties of celluar rubber products particulary for those elastomers such as EPDM, CR and NBR with heat resistance property, weather proofness, and oil resistance characteristics respectively, aiming at improving their quality, and renovating the manufacturing know-how which is beyond our technical power at the present time in Korea. In order to meet this requirement an ideal recipe is being shown for the three elastomers, and also a practical recipe which is easily available in terms of compounding ingredients in domestic market has set up as shown in Table 1. for the investigation of vulcanization characteristics by means of Rheometer. The optimum Mooney viscosity of compounded rubber was found to be approximately $ML_{1+4}(100^{\circ}C)$ $30\sim45$. Excess mustication makes a dispersion of ingredients worse, consequently it causes deformation of shapes and heterogenous cell distribution. In other words the articles are rejected because of its insufficient workmanship. The results of physical properties of the products are indicated in Table 3. It has shown that the quality meet requirement when tested in accordance with ASTM D572, 573 and D 395. The test results o CR/IR blends in terms of hardness, volume change by blowing, tensile strength and elongation have been shown.

• Journal of Adhesion and Interface
• /
• v.1 no.1
• /
• pp.15-22
• /
• 2000

To prepare acrylic type pressure-sensitive adhesive, quarter polymers were synthesized from butylacrylate (BA), 2-ethylhexylacrylate (2-EHA), methyl methacrylate (MMA), 2-hydroxyethylmethacrylate (2-HEMA). The quarter polymer was identified by FT-IR. Molecular weight was measured by Gel Pearmeation Chromatograhy. Also, viscosity, solid content and peel strength were investigated. The peel strength was $160g_f/25mm$ when the volume ratio of feed monomer to solvent was 1.3:1 and the ratio was relevant to commercial usage. The pot life of adhesive was 30 s at the 50 m/min of heat treatment rate, and it indicated that the minimum drying time was 30 s. Not only weathering resistance keep up peel strength $160{\sim}180g_f/25mm$ after 1000 h, but also no residual remains.

• Progress in Superconductivity and Cryogenics
• /
• v.20 no.4
• /
• pp.11-15
• /
• 2018

Torque tubes in High Temperature Superconducting (HTS) motor transfer torque from superconducting field winding rotor to the room temperature shaft. It should have minimum heat conduction property for minimizing the load on cryo-refrigerator. Generally, these torque tubes are made with stainless steel material because of high strength, very low outgassing and low thermal contraction properties at cryogenic temperatures and vacuum conditions. With recent developments in composite materials, these torque tubes could be made of composites such as Kevlar and S-Glass, which have the required properties like high strength and low thermal conductivity at cryogenic temperatures, but with a reduced weight. Development and testing of torque tubes made of these composites for HTS motor are taken up at Bharat Heavy Electricals Limited (BHEL), Hyderabad in collaboration with Central Institute of Plastics and Engineering Technology (CIPET), Chennai and Indian Institute of Technology (IIT), Kharagpur. As these materials are subjected to vacuum, it is important to measure their outgassing rates under vacuum conditions before manufacturing prototype torque tubes. The present study focusses on the outgassing characteristics of Kevlar and S-Glass, using an Outgassing Measurement System (OMS), developed at IIT Kharagpur. The OMS facility works under vacuum environment, in which the test samples are exposed to vacuum conditions over a sufficient period of time. The outgassing measurements for the composite samples were obtained using pressure-rise technique. These studies are useful to quantify the outgassing rate of composite materials under vacuum conditions and to suggest them for manufacturing composite torque tubes used in HTS motors.

• The Journal of Korean Medicine
• /
• v.42 no.2
• /
• pp.107-119
• /
• 2021

Objectives: This study was aimed to report changes in clinical symptoms and signs after treatment with Korean medicine in patients who suffered from calf edema due to deep vein thrombosis (DVT). Methods: A 46-year-old male patient, who discharged home after receiving standardized treatment for acute DVT in the right leg, suffered pain and heat sense due to edema of the affected calf. Oral administration of herbal medicine (Gyejibongnyeong-hwan 4 g, twice daily) and acupuncture therapy were given to him for 6 weeks. The change in chief complaints, Villalta score, the right and left side difference of the circumference and the skin surface temperature of both calves, and blood level of D-dimer were observed before and after treatment. Results: The patient's chief complaints began to significantly improve from 2 weeks after treatment, and disappeared completely within 4 weeks. At the end of the treatment, a substantial decrease in the difference between the right and left calves in the circumference and skin surface temperature was observed. This effect was maintained even at the time of follow-up 3 months after the end of treatment, and the patient completely recovered indoor and outdoor life to the level before onset. Conclusions: This case suggests that Korean medicine treatment, including Gyejibongnyeong-hwan administration and acupuncture therapy, can be a viable option to improve edema and related clinical problems in the affected limbs due to DVT.