• Journal of the Korean Wood Science and Technology
• /
• 제44권3호
• /
• pp.457-476
• /
• 2016

본 연구에서는 목재의 열처리가공에 대하여, 문헌 연구를 통하여 이와 관련된 주요 이슈 및 기술 동향을 조사하였다. 산업적으로 이용되는 주요 열처리기술은 네덜란드의 Plato-process, 프랑스의 Retification process, 독일의 OHT-process, 및 핀란드의 Thermowood process 등이었다. 열처리 공정상의 주요 영향인자들은 대상 수종, 가열 온도, 시간, 열전달 매질(air, 증기, 진공, 질소, 오일 등)이며, 이들 인자들을 변수로 한 최적조건 탐색 등의 연구가 주류를 이룬다. 열처리 목재는 치수안정성 증가, 중량 및 강도 감소, 부후균에 대한 내후성 향상에 변이, 변색균 및 해충에 대해 불충분한 저항성 등의 특징을 가진다. 열처리 목재의 내후성 향상을 위해 각 수종에 적합한 열처리 공정과 처리조건 탐색의 필요성이 시사되었다. 지속가능한 환경보존 및 목재자원 절약을 위해 열처리 목재의 새로운 용도 개발 및 이용 확대 노력이 반드시 필요한 과제인 것으로 고찰되었다.

• 한국가시화정보학회지
• /
• 제20권3호
• /
• pp.58-66
• /
• 2022

The high heat emitted from the process module and heat jacket may cause errors in semiconductor process equipment. Barriers were designed to reduce the temperature of surface on transfer module. A designed barrier was compared and analyzed by numerical analysis using ANSYS Fluent. The average temperature of barrier and effect of radiation heat transfer were also compared through absorbed radiative heat flux of the barrier. The adoption of the barrier had an effect on the radiative heat transfer reduction of the transfer module rod. The effect of the angles of barrier from 50° to 90° on the heat transfer was investigated using the absorbed radiative heat flux with the average temperature. The angle of barrier of 50° reduced the temperature up to 9.6 %.

• 한국기계가공학회지
• /
• 제10권5호
• /
• pp.79-84
• /
• 2011

Air pollutants from a small marine diesel engine are increasing and the IMO(International Marine Organization) regulation asked for its reduction. In this study, NOx reduction technologies such as improvement of various cooling systems are applied to the small marine diesel engine. The various cooling systems are a intercooler, a heat exchanger for engine coolant, and an exhaust manifold by water cooling. These systems are tested on an engine dynamometer and a exhaust gas analyzer by a marine diesel engine test regulation. Test results are shows that the small marine engine are satisfied the IMO NOx regulations; Tire II.

• 한국기계가공학회지
• /
• 제14권4호
• /
• pp.21-27
• /
• 2015

Induction bending is a method that allows the bending of any material that conducts electricity. This technology applies a bending force to a material that has been locally heated by an eddy current induced by a fluctuating electromagnetic field. Induction bending uses an inductor to locally heat steel through induction. This results in a narrow heat band in the shape to be bent. In general, the reduction of thickness attenuation of a large-diameter steel pipe is not allowed to exceed 12.5%. In this paper, in order to meet the standard of thickness attenuation reduction, a non-uniform heating temperature jump-bending process was investigated. As a result, the developed bending technique meets the requirements of thickness attenuation reduction for large-diameter steel pipes.

• 설비공학논문집
• /
• 제13권3호
• /
• pp.200-208
• /
• 2001

In indoor temperature control of a heat pump, a reduction in energy consumption is very important. However, most control schemes for heat pumps have focused only on control performance such s settling time and steady-state error. In this paper, the model predictive control (MPC) which includes the energy-related variable in this cost function is proposed. By computing the control signal minimizing this cost function, the trade-off between energy reduction and temperature control performance can be obtained. Since the MPC required the process model, the dynamic mode of a heat pump is also obtained by the system identification technique. Performance of the proposed MPC considering energy efficiency is compared with the two other control schemes. It si shown that the proposed scheme can consume less energy thant hte others in achieving similar control performance.

• 한국분말재료학회지
• /
• 제16권5호
• /
• pp.310-315
• /
• 2009

Ultra-fine TiC/Co composite powder was synthesized by the carbothermal reduction process without wet chemical processing. The starting powder was prepared by milling of titanium dioxide and cobalt oxalate powders followed by subsequent calcination to have a target composition of TiC-15 wt.%Co. The prepared oxide powder was mixed again with carbon black, and this mixture was then heat-treated under flowing argon atmosphere. The changes in the phase, mass and particle size of the mixture during heat treatment were investigated using XRD, TG-DTA and SEM. The synthesized oxide powder after heat treatment at 700$^{\circ}C$ has a mixed phase of TiO$_2$ and CoTiO$_3$ phases. This composite oxide powder was carbothermally reduced to TiC/Co composite powder by the solid carbon. The synthesized TiC/Co composite powder at 1300$^{\circ}C$ for 9 hours has particle size of under about 0.4 $\mu$m.

• 열처리공학회지
• /
• 제30권6호
• /
• pp.251-257
• /
• 2017

The effect of annealing temperature on the martensitic transformation behavior, tensile deformation chracteristics and shape recovery etc., has been studied in TiNi based shape memory ribbon fabricated by coldrolling of wire. TiNi based shape memory wire (${\phi}=500{\mu}m$) of which structure is intermetallic compound could be cold-rolled without process annealing up to the reduction rate in thickness of 50%, but a few cracks appear in cold-rolled ribbon in the reduction rate in thickness of 65%. The $B2{\rightarrow}R{\rightarrow}B19^{\prime}$ martensitic transformation or $B2{\rightarrow}B19^{\prime}$ martensitic transformation occurs in annealing conditions dissipating lattice defects introduced by coldrolling. However, in case of higher reduction rate or lower annealing temperature, martensitic transformation in cold-rolled and then annealed ribbons does not occur. The maximum shape recovery rate of cold-rolled ribbons with the reduction rate of 35 and 65% could be achieved at annealing temperatures of 250 and $350^{\circ}C$, respectively. The shape recovery rate seems to be related to the stress level of plateau region on stress-strain curve.

• 한국기계가공학회지
• /
• 제11권3호
• /
• pp.166-173
• /
• 2012

This study is about comparison of thermal and flow characteristics on the wind & radiant heat shield with STS mesh type screen for offshore. Numerical analysis was conducted to find transmission coefficient in the mesh and then analyse the flow characteristics about wind & radiant heat shield. The experiment method of solar radiation has been used as thermal radiation source to get the performance of radiant heat shield measurement. The sensor radiation device has been used to measure the reduction of solar radiation with various size of cells and at a distance of 0.5m and 1m from the cold face of the wind & radiant heat shield.

• 한국재료학회지
• /
• 제34권4호
• /
• pp.208-214
• /
• 2024

To fabricate intermetallic nanoparticles with high oxygen reduction reaction activity, a high-temperature heat treatment of 700 to 1,000 ℃ is required. This heat treatment provides energy sufficient to induce an atomic rearrangement inside the alloy nanoparticles, increasing the mobility of particles, making them structurally unstable and causing a sintering phenomenon where they agglomerate together naturally. These problems cannot be avoided using a typical heat treatment process that only controls the gas atmosphere and temperature. In this study, as a strategy to overcome the limitations of the existing heat treatment process for the fabrication of intermetallic nanoparticles, we propose an interesting approach, to design a catalyst material structure for heat treatment rather than the process itself. In particular, we introduce a technology that first creates an intermetallic compound structure through a primary high-temperature heat treatment using random alloy particles coated with a carbon shell, and then establishes catalytic active sites by etching the carbon shell using a secondary heat treatment process. By using a carbon shell as a template, nanoparticles with an intermetallic structure can be kept very small while effectively controlling the catalytically active area, thereby creating an optimal alloy catalyst structure for fuel cells.

• KIEAE Journal
• /
• 제14권5호
• /
• pp.123-130
• /
• 2014

In order for effective heat island reduction policies to be proposed, this research made use of the land usage and land coverage and Temperature of cities, Coordinate axis data within 500 meters of nationwide automatic weather stations (478 points) in order to analyze the correlation of summertime temperatures through multiple regression analysis. This research also developed a model and empirically analyzed the urban heat island reduction effect of factors that affect regional temperatures. Heat islands cause environment deterioration and therefore can harm citizens' health, and also affects the city's metabolism process. Thus in order to restrain regional temperature rises the conclusion was drawn that consideration to increase forest areas on part of land usage planning is needed. Appropriate policy measures to regulate traffic related factors are also needed to restrain regional temperature rises. In order for future heat island reduction this research proposes a way to set up more effective policies and urban sustainability improvement strategies, and is significant in that it makes use of detailed data such as land usage and land coverage, Temperature of cities, Coordinate axis in analyses.