• Journal of Welding and Joining
• /
• 제29권1호
• /
• pp.80-84
• /
• 2011

The weight reduction of the transportations has become an important technical subject Al and Al alloys, especially Al 5052 alloys have been being applied as door materials for automobile. One of the most widely known car weight-reduction methods is to use light and corrosion-resistant aluminum alloys. However, because of high electrical and thermal conductivity and a low melting point, it is difficult to obtain good weld quality when working with the aluminum alloys. Also, Pulse MIG welding is the typical aluminum welding process, but it is difficult to apply to the thin plate, because of melt-through and humping-bead. In order to enhance weld quality, welding parameters should be considered in optimizing the welding process. In this experiment, Al 5052 sheets were used as specimens, and these materials were welded by adopting new Cold Metal Transfer (CMT) pulse process. The proper welding conditions such as welding current, welding speed, torch angle $50^{\circ}$ and gap 0~1mm are determined by tensile test and bead shape. Through this study, range of welding current are confirmed from 100A to 120A. And, the range of welding speed is confirmed from 1.2m/min to 1.5m/min.

• 한국식품과학회지
• /
• 제18권1호
• /
• pp.61-65
• /
• 1986

홍옥(紅玉)을 시료(試料)로 하여 건조조건(乾燥條件)을 다르게하여 건조특성(乾燥特性), 수분이동현상(水分移動現像), 건조중(乾燥中) 시료온도(試料溫度) 및 내부수분(內部水分)의 분포(分布)를 조사하였다. 사과의 수분확산계수(水分擴散係數)는 $1.1470{\sim}2.2148{\times}10^{-5}cm^2/sec$, 확산활성화(擴散活性化)에너지는 6.6 kcal/g mole 이었으며 Fick's law에서 아래의 식을 유도할 수 있었다. $${\In}\;{\Delta}t=In\;{\Delta}to-{\frac{D{\pi}^2{\theta}}{4d^2}}$$ 건조중(乾燥中) 내부수분분포(內部水分分布)의 이론치(理論値)와 실측치(實測値)는 거의 일치하였다.

• 태양에너지
• /
• 제18권3호
• /
• pp.185-195
• /
• 1998

본 연구는 태양열을 이용한 냉난방 공조시스템 개발 중 작동매체인 저농도의 염화리튬(lithium chloride) 용액을 고농도로 변환시키는 재생기의 최적 재생면을 파악하는 데 그 목적이 있다. 염화리튬 용액은 점성이 강하기 때문에 재생기의 상부로부터 하부로 유하될 때 편류(Channeling)현상을 발생하게 된다. 이 편류현상은 재생기에서의 열 및 물질전달을 방해하여 재생량을 감소시킨다. 결국 재생기의 성능, 나아가서는 태양열 이용 냉난방 공조시스템 전체의 성능이 염화리튬용액을 얼마나 균일하게 유하할 수 있는 가에 달렸다고 해도 과언은 아니다. 따라서 본 연구에서는 재생면의 다양한 형태와 구조를 고안해서 실제로 재생면을 제작하여 재생면의 최적 구조를 규명하였다. 실험을 위하여 가로 50cm, 세로 50cm 크기인 간이 재생기를 직접 제작하여 항온항습실에서 실험을 행하였다. 그 결과 평판 위에 높이 4.5mm 폭 10mm의 계단형 구조를 갖는 재생면에서 최대의 재생량을 얻을 수 있었다.

• 한국태양에너지학회 논문집
• /
• 제29권4호
• /
• pp.28-33
• /
• 2009

In 2008, the global photovoltaic(PV) market reached 5.6GW and the cumulative PV power installed totalled almost 15GW compared to 9GW in 2007. Due to a favourable feed-in-tariff, Korea emerged in 2008 as the 4th largest PV market worldwide. PV power installation rose 495.5 percent to 268MW in 2008 compare to 45MW in 2007. Building integrated photovoltaic(BIPV) has the potential to become a major source of renewable energy in the urban environment. BIPV has significant influenced on the reflection by rear materials such as white back sheet and the heat transfer through the building envelope because of the change of the thermal resistance by adding or replacing the building elements. In this study, to use as suitable building materials into environmentally friendly house like green home, characteristic analysis of BIPV module according to rear materials achieved. Electrical output of PV module with white back sheet is high about 10% compared to other pv module because of 83% reflectivity of white back sheet compared to 8.4% reflectivity of other PV modules with different rear materials(black back sheet and glass). In the result of outdoor experiment during a year, electrical output of four different PV module is decreased about 3.72%.

• 한국초전도ㆍ저온공학회논문지
• /
• 제16권1호
• /
• pp.36-41
• /
• 2014

Since glass microsphere has high crush strength, low density and small particle size, it becomes alternative thermal insulation material for cryogenic systems, such as storage and transportation tank for cryogenic fluids. Although many experiments have been performed to verify the effective thermal conductivity of microsphere, prediction by calculation is still inaccurate due to the complicated geometries, including wide range of powder diameter distribution and different pore sizes. The accurate effective thermal conductivity model for microsphere is discussed in this paper. There are four mechanisms which contribute to the heat transfer of the evacuated powder: gaseous conduction ($k_g$), solid conduction ($k_s$), radiation ($k_r$) and thermal contact ($k_c$). Among these components, $k_g$ and $k_s$ were calculated by Zehner and Schlunder model (1970). Other component values for $k_c$ and $k_r$, which were obtained from experimental data under high vacuum conditions were added. In this research paper, the geometry of microsphere was simplified as a homogeneous solid sphere. The calculation results were compared with previous experimental data by R. Wawryk (1988), H. S. Kim (2010) and the experiment of this paper to show good agreement within error of 46%, 4.6% and 17 % for each result.

• 항공우주시스템공학회지
• /
• 제11권5호
• /
• pp.6-12
• /
• 2017

본 논문은 75톤급 개방형(Open-cycle) 액체로켓엔진(Liquid Propellant Rocket Engine, LPRE)의 수학적 모델링 및 정상상태(Steady state)에서의 시뮬레이션을 수행한 내용을 다룬다. 액체로켓엔진의 각 구성품들은 열역학 및 동역학적 특성을 이용하여 크게 7개로 분류할 수 있으나, 본 논문의 액체로켓엔진 시뮬레이션 모델을 간단화하기 위해 열전달 모델링을 생략하여 4개의 지배방정식(Govern equation)을 이용하였다. 정상상태에서의 실험 데이터와 시뮬레이션 데이터의 오차율을 통해 모델링을 확인하였으며 공칭 작동점에서의 선형화 모델을 이용하여 안정성을 판단하였다. 또한, 시뮬레이션 모델링을 검증하기 위해 실험 데이터의 과도응답을 비교하였다.

• 설비공학논문집
• /
• 제21권9호
• /
• pp.505-512
• /
• 2009

A thermosiphon is utilized as a thermal shunt to reduce the cool-down time of a cryogenic system cooled by a two stage cryocooler. The cool-down time reduction by the thermosiphon is determined by the type of working fluid which is directly related to the operating temperature range of the thermosiphon. A mixed working fluid has a potential to widen the operation temperature range of the thermosipohon. In this study, the thermosiphon using N$_2$ and CF$_4$ mixture as the working fluid is fabricated and tested to verify its transient heat transfer performance. The thermosiphon with the mixed working fluid has no noticeable reduction of cool-down time compared with that of the thermosiphon with pure working fluid in this experiment. However, it seems that the thermosiphon with mixed working fluid may have an advantage according to the cooling capacity of a cryocooler, the cooling target temperature and the size of a cooling object.

• 한국환경과학회지
• /
• 제16권3호
• /
• pp.261-267
• /
• 2007

In this study, the Slab Ocean Model (SOM) is coupled with an Atmospheric General Circulation Model (AGCM) which developed in University of Kangnung based on the land surface model of Biosphere-Atmosphere Transfer Scheme (BATS). The purposes of this study are to understand radiative role of clouds considering of the atmospheric feedback, and to compare the Clouds Radiative Forcing (CRF) come from the analyses using the clear-cloud sky method and CGCM. The new CGCM was integrated by using two sets of the clouds with radiative role (EXP-A) and without radiative role (EXP-B). Clouds in this two cases show the negative effect $-26.0\;Wm^{-2}$ of difference of radiation budget at top of atmosphere (TOA). The annual global means radiation budget of this simulation at TOA is larger than the estimations ($-17.0 Wm^{-2}$) came from Earth Radiation Budget Experiment (ERBE). The work showed the surface negative effect with $-18.6 Wm^{-2}$ in the two different simulations of CRF. Otherwise, sensible heat flux in the simulation shows a great contribution with positive forcing of $+24.4 Wm^{-2}$. It is found that cooling effect to the surface temperature due to radiative role of clouds is about $7.5^{\circ}C$. From this study it could make an accurate of the different CRF estimation considering either feedback of EXP-B or not EXP-A under clear-sky and cloud-sky conditions respectively at TOA. This result clearly shows its difference of CRF $-11.1 Wm^{-2}$.

• 한국농공학회논문집
• /
• 제54권5호
• /
• pp.1-7
• /
• 2012

본 연구의 목적은 국내에서 상용되고 있는 온실 피복재 및 보온재의 조합에 따른 관류열전달계수를 핫박스를 이용하여 평가하는 것이다. 온실용 일중 및 이중 피복재와 이중 보온재의 조합에 대하여 야간천공복사 차단여부에 따른 관류열전달계수를 핫박스를 이용하여 실외에서 측정하였다. 처리조건은 일중피복, 이중피복, 이중피복과 이중 마트보온재 및 이중피복과 이중 다겹보온재의 조합조건과 천공복사 유무에 따른 조건이며 총 8가지이다. 제작된 핫박스는 상시 변화하는 외부의 기상조건하에서도 내부온도를 설정된 온도로 일정하게 잘 유지할 수 있었다. 온실 피복재 및 보온재의 관류열전달계수를 측정하는 실내용 측정장치는 반드시 야간천공복사를 모의할 수 있는 측정장치가 되어야 할 것이다. 야간복사를 차단함으로서 온실의 열 손실을 줄여 보온효과를 얻을 수 있을 것으로 분석되었다. 모든 피복방식에 대해 야간복사 차단장치 유무에 관계없이 높은 풍속에서의 관류열전달계수가 낮은 풍속에서보다 더 큰 것으로 나타났다. 본 연구에서 사용된 측정기법을 사용하면 국내에서 생산되는 피복재 및 보온재의 관류열전달 특성을 정량적으로 비교할 수 있을 것으로 기대된다.

• 대한기계학회논문집B
• /
• 제26권2호
• /
• pp.288-301
• /
• 2002

A vacuum freeze drying experiment of skim milk solution in a cylindrical container is conducted to investigate the multi-dimensional drying characteristics of the process during the primary drying stage. Temperature histories at several positions are measured under the same process condition that is carefully controlled. Then the measured temperature histories at different positions are combined to produce instantaneous temperature distribution fields inside the cylindrical container. Along with the temperature measurement, the mass reduction history of the skim milk solution is also measured. From the measured temperature distribution curved configurations of sublimation interfaces and 2-dimensional heat transfer is inferred. The freeze drying under the present experimental setup is simulated with a calculation program that is based on a finite volume method with a moving grid system. Good agreements between the numerical and experimental results are observed. The present experimental results and the numerical approaches can be useful information in developing the analysis tools for practical vacuum freeze drying processes.