• Journal of the Korean Institute of Gas
• /
• v.1 no.1
• /
• pp.1-6
• /
• 1997

In case of using the electrical apparatus in the hazardous atmosphere which exist flammable gas mixtures, There is a dangerosity of gas explosion accident by the electrical spark. The most general method to prevent the explosion by the spark is to use the flame-proof type electrical apparatus to isolate the ignition source. from the flammable atmosphere. But actualy it is impossible to isolate the ignition sources from the atmosphere. So it was needed to find the safe gap which prevent ignition of flammable atmosphere by transmission of flame or heat when a flammable gas mixture exploded inside the apparatus. In this study we tried to find the maximum experimental safe gap(MESG) of $H_2$-air, and $CH_4$-air mixtures by using the 8 litre spherical vessel with 25mm flange. The experiment parameter were ignition position, concentration and initial pressure before explosion. From the experiment the ignition position was affected to the MESG. MESG value was minimum near the stoichiometric concentration of gas mixtures, and according to the increase of initial pressure MESG was decreased.

• Journal of the Korean Society of Safety
• /
• v.33 no.2
• /
• pp.32-38
• /
• 2018

The sprinkler system is a basic fire extinguishing system widely used, but there is a lack of quantitative assessment of its performance. In this study, to evaluate the fire extinguishing performance of the sprinkler head according to the discharge coefficients, experiments were conducted. Experimental sprinkler heads were selected with heads having K50, K80 and K115 water discharge coefficients, and the fire source was assumed to be an indoor fire in Class A Model 1. As experimental results, the time required for the fire chamber to cool down to $200^{\circ}C$ was 26 seconds for the K115 head, 414 seconds for the K80 head, and 481 seconds for the K50 head, so the cooling time of the K115 head was decreased by 94.5% compared to K50 head. In the case of restoring the oxygen concentration to 15%, the K115 head did not decrease below the oxygen concentration of 15%, and the K80 head took 145 seconds and the K50 head took 484 seconds. The lowest oxygen concentration in the fire chamber was 16.1% for the K115 head, 14.33% for the K80 head, and 11.28% for the K50 head, indicating that the K115 head was superior to the K80 and K50 heads by 13.1% and 43.7%, respectively. As the experimental results show, there is big difference in the extinguishing performance depending on the discharge coefficients of the sprinkler head. Therefore, in designing the sprinkler system, the discharge coefficients of the sprinkler head should be selected considering the heat release rate at the installation site and the fire extinguishing characteristics of sprinkler head.

• Journal of Power Electronics
• /
• v.4 no.3
• /
• pp.138-151
• /
• 2004

In this paper, a constant frequency phase shifting PWM-controlled voltage source full bridge-type series load resonant high-frequency inverter using the $4^{th}$ generation IGBT power modules is presented for innovative consumer electromagnetic induction heating applications, such as a hot water producer, steamer and super heated steamer. The bridge arm side link passive capacitive snubbers in parallel with each power semiconductor device and AC load side linked active edge inductive snubber-assisted series load resonant tank soft switching inverter with a constant frequency phase shifted PWM control scheme is evaluated and discussed on the basis of the simulation and experimental results. It is proved from a practical point of view that the series load resonant and edge resonant hybrid high-frequency inverter topology, what is called, DE class type, including the variable-power variable-frequency regulation function can expand zero voltage soft switching commutation area even under low output power setting ranges, which is more suitable and acceptable for newly developed induction heated dual pack fluid heaters. Furthermore, even the lower output power regulation mode of this high-frequency load resonant tank inverter circuit is verified so that this inverter can achieve ZVS with the aid of the single auxiliary inductor snubber.

• Resources Recycling
• /
• v.12 no.5
• /
• pp.50-56
• /
• 2003

To be recycled iron and heat source in EAF, EAF dust and mill scale generated from steelmaking plant should be made to iron carbide. Behavior of reduction and carburization in EAF dust and mill scale is studied to get fundamental data. EAF dust and mill scale are carburized at $650^{\circ}C$ by 100% CO gas. The carbon content of iron carbide(about 9 wt,% C) is higher than that of cementite without free carbon. The 1.2 times of calculated carbon content is suitable for reduction of EAF dust. The reduction temperature is appropriate to $900^{\circ}C$ in EAF dust and $1000^{\circ}C$ in mill scale. The carburization rate of mill scale are faster than those of EAF dust. The composition of super iron carbide is almost $Fe_2$C.

• Journal of Power System Engineering
• /
• v.17 no.6
• /
• pp.102-107
• /
• 2013

In this paper, the performance analysis for evaporation capacity, total work and efficiency of the ocean thermal energy conversion(OTEC) power system using mixed refrigerant(R32,R152a) is conducted to find the effect of hot wasted water on OTEC power system. The system in this study is applied with two stage turbine, regenerator, cooler and separator on Organic Rankine Cycle. The commercial program HYSYS is used for the performance analysis. The main results were summarized as follows : The efficiency of the OTEC power cycle has a largely effect on the evaporation capacity and total work. As increasing temperature of heat source water, evaporator's capacity is decreased but total work increase. Otherwise, using hot wasted water bring effects not only increasing system efficiency but also declining evaporator's capacity. Thus With a thorough grasp of these effect, it is necessary to find way to use hot wasted water emitted by power plant and so on.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.58 no.3
• /
• pp.357-361
• /
• 2009

This study performed analysis on the thermal pattern and current characteristics of an LED ((Light Emitting Diode) street lamp. It did this using a TVS (Thermal Video System) to analyze the LED street lamp's thermal pattern, and measured its characteristics using an oscilloscope. The ambient temperature and humidity during the experiment were maintained at $24{\pm}2[^{\circ}C]$ and 50~60[%]. The capacity of the LED street lamp was 120[W] and nine sets of modules were arranged at uniform intervals. On one module, 24 LED lamps were arranged in a radial pattern. The analysis of the thermal diffusion pattern at the front of the LED lamp showed that the maximum surface temperature was approximately $34[^{\circ}C]$. In addition, there was almost no change in the temperature of the upper cover, and the temperature at the side showed a uniform thermal diffusion pattern. The surface temperature of the converter converting AC to DC increased to approximately $46[^{\circ}C]$. The analysis results of the thermal characteristics of one LED indicated uniform thermal characteristics for an initial eight minutes. However, the temperature at the center of the LED increased to approximately $82[^{\circ}C]$ after 12 minutes had elapsed. It can be seen from this that the temperature at the center of the LED was higher than the allowable temperature, $70[^{\circ}C]$ of the insulating material for general electrical devices. Therefore, it is necessary to design a lamp in such a way that the plastic insulating material does not come into contact with or get close to the LED lamp. The voltage of the LED lamp converted by the AC/DC converter was measured at DC 27[V] and the current was DC 13[A]. Consequently, it can be seen that in order to secure an adequate light source, it is important to supply a stable current that was greater than the current of other light sources. Therefore, appropriate radiation of heat is required to secure the stability and reliability of the system.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.9
• /
• pp.979-988
• /
• 2014

Recently, the interest in the thermal comfort is ever increasing as the time people stay in the automobile is gradually increasing. So far, however, the cooling performance of the HVAC(heating and ventilation air conditioning) system is evaluated by thermal environment criteria such as indoor air velocity and temperature, not by a thermal comfort index. Furthermore, the precise criteria has not been established yet when the thermal comfort for the automobile is evaluated using numerical analysis. In this study, the numerical analysis of automobile indoor thermal comfort according to various parameters such as HVAC operating mode, airflow, passenger boarding conditions is performed during the HVAC system's initial operating time(20 minutes). The solar ray tracing model and S2S radiation model are used and validated to simulate an external heat source. Based on this study, an evaluation model which can predict the thermal comfort index for the combination of the above parameters is presented.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.498-498
• /
• 2013

Atmospheric Pressure Plasmas have pioneered a new field of plasma for biomedical application bridging plasma physics and biology. Biological and medical applications of plasmas have attracted considerable attention due to promising applications in medicine such as electro-surgery, dentistry, skin care and sterilization of heat-sensitive medical instruments [1]. Traditional approaches using electronic devices have limits in heating, high voltage shock, and high current shock for patients. It is a great demand for plasma medical industrial acceptance that the plasma generation device should be compact, inexpensive, and safe for patients. Microwave-excited micro-plasma has the highest feasibility compared with other types of plasma sources since it has the advantages of low power, low voltage, safety from high-voltage shock, electromagnetic compatibility, and long lifetime due to the low energy of striking ions [2]. Recent experiment [2] shows three-log reduction within 180-s treatment of S. mutans with a low-power palm-size microwave power module for biomedical application. Experiments using microwave plasma are discussed. This low-power palm-size microwave power module board includes a power amplifier (PA) chip, a phase locked loop (PLL) chip, and an impedance matching network. As it has been a success, more compact-size module is needed for the portability of microwave devices and for the various medical applications of microwave plasma source. For the plasma generator, a 1.35-GHz coaxial transmission line resonator (CTLR) [3] is used. The way of reducing the size and enhancing the performances of the module is examined.

• Economic and Environmental Geology
• /
• v.32 no.3
• /
• pp.293-306
• /
• 1999

The lower Permian jungseong Formation, Taebaegsan basin (Baegunsan Syncline), represents a coal-bearing siliciclastic succession which was later modified by the Songrim or Dabo orogeny. Sandstone perography and clay mineralogy were studied to understand the thermal history of the Jangseong Formation during basin evolution. Petrographic study indicates the Jangseong sandstones are composed of quartz, feldspar, lithic fragments (metamorphic and sedimetary), and varying proportions of matrix and cement. The dominance of quartz(<97%) over feldspar (<1%) and lithic fragments (<2%) classifies most Jangseong sandstones as quartz arenotes or quartzwackes, but lithic graywackes and sublithic arenite locally occur. The diagentic features of these sandstones include mechanical compaction, cemenation by quartz and clay minerals indentified in the Jangseong Formation by X-ray diffraction analysis are late-stage clay pore-filling. Clay minerals isdentified in the Jangseong Formation by X-ray diffaction analysis are illite, kaolinte, and pyrophyllite with a minor amount of chlorite and micas. The illite, kaolinite, and pyrophyllite appear to be largely autjigenic based on their well-crystallinity forms. There authigenic clay minerals form clay minerals form clay coats/rims and late-stage pore-filling cements, Illitecrystallinity shows that the Jangseong formation has been in late-diagenetic zone to early-epizone, which ranges in temperature from $200^{\circ}C$ to $300^{\circ}C$. In assition, kaolinite-pyrophyllite transition suggests that paleotemperature of the formation has reached at least $265^{\circ}C$. Such temperatureis likely to be consistent with homogenixation temperatures of fluid inclusions in quartz veins in the formation. Thus, the Jangseong Formation has been subjected to paleotemperature of about $265^{\circ}C$. The major heat source responsible for paleotemperature may be hydrothermal solutions. The passage of hydrothermal solutions was probably assisted by fractures created during the basin-modifying tectonism of the taebaegsan basin.

• Microbiology and Biotechnology Letters
• /
• v.44 no.3
• /
• pp.349-354
• /
• 2016

A variety of nuruks collected in different areas in Korea were explored to isolate sixty yeast strains that was able to grow at 44℃. MBY/L1569 strain, which showed the highest growth rate, was selected and identified as Pichia farinosa (Millerozyma farinosa). The isolated strain exhibited superior resistance to heat, acid, and alkali compared with those of P. farinosa KCTC27412 as a control strain. The specific growth rate of P. farinosa MBY/L1569 at 46℃ was 0.37 ± 0.05 h⁻¹, and the highest specific growth rate of 0.50 ± 0.02 h⁻¹ was obtained when it was grown at pH 7.0 and 37℃ with 50 g/l (w/v) glucose as the carbon source. Under optimum growth conditions, strain MBY/L1569 produced ethanol 19.66 ± 0.68 g/l from glucose 50 g/l, with an approximate yield of 40%. P. farinosa MBY/L1569 was deposited at the Korean Collection for Type Cultures as pichia farinosa KCTC27753.