• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.03a
• /
• pp.7-7
• /
• 2010

Energy harvesting from the environment has been of great interest as a standalone power source of wireless sensor nodes for Ubiquitous Sensor Networks(USN). In particular, the piezoelectric energy harvesting from ambient vibration sources has intensively researched because it has a relatively high power density comparing with other energy scavenging methods. Through recent advances in low power consumption RF transmitters and sensors, it is possible to adopt a micro-power energy harvesting system realized by MEMS technology for the system-on-chip. However, the MEMS energy harvesting system has some drawbacks such as a high natural frequency over 300 Hz and a small power generation due to a small dimension. To overcome these limitations, we devised a novel power generator with a spiral spring structure as shown in the figure. The natural frequency of a cantilever could be decreased to the usable frequency region (under 300 Hz) because the natural frequency depends on the length of a cantilever. In this study, the natural frequency of the energy harvester was a lower than a normal cantilever structure and sufficiently controllable in 50 - 200 Hz frequency region as adjusting weight of a proof mass. Moreover, the MEMS energy harvester had a high energy conversion efficiency using a shear mode ($d_{15}$) is much larger than a 33 mode ($d_{33}$) and the energy conversion efficiency is proportional to the piezoelectric constant (d). We expect the spiral type MEMS power generator would be a good candidate for a standalone power generator for USN.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.10
• /
• pp.766-772
• /
• 2012

Spring supported piezoelectric cantilever structures (SPCS) were fabricated for vibration-based energy harvester application. We selected four elastic springs (A, B, C, and D type) as cantilever's supporter, each elastic spring has a different spring constant (S). The C type of SPCS ($S_C$: 4,649 N/m) showed a extremely low resonance frequency of 81 Hz along with the highest power output of 38.5 mW while the A type of SPCS ($S_A$: 40,629 N/m) didn't show a resonance frequency while. Therefore, it is considered that the lower spring constant lead to a lower resonance frequency of the SPCS. In addition, a tip mass (18 g) at one end of the SPCS could further reduce the resonance frequency without heavy degradation of power output.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.8
• /
• pp.501-507
• /
• 2017

A unimorph piezoelectric cantilever generator with an interdigitated electrode (IDE) was developed for vibration energy harvester applications driven in the longitudinal mode. Hard lead zirconate titanate (PZT) ceramic with a high $Q_m$ of 1,280 was used as the piezoelectric active material. Ten PZT sheets produced by tape casting were laminated and co-fired with an Ag/Pd IDE at $1,050^{\circ}C$ for 2 h. The approximately $280{\mu}m$-thick co-fired PZT laminate with the IDE was attached to a stainless steel substrate with an adhesive epoxy for the fabrication of an IDE unimorph cantilever. Its energy harvesting characteristics were evaluated: an output power of $1.1{\mu}W$ at 120 Hz across the resistive load of $700k{\Omega}$ was obtained, corresponding to a normalized power factor of $4.1{\mu}W/(G^2{\cdot}cm^3)$.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.1
• /
• pp.40-48
• /
• 2016

Micro-vibration induced by on-board appendages that have mechanical moving parts has always been treated as an useless objective that has to be isolated, in order to comply with a high-resolution mission requirement of the observation satellite. In this study, we proposed a tuned mass damper energy harvester combined with a conventional passive vibration isolator for exhibiting dual functions of both electrical energy harvesting and micro-vibration isolation. The feasibility of the proposed dual-function complex system has been demonstrated through the comparison with numerical simulations, based on the results of basic characteristic tests, and experiments of the harvested power and micro-vibration.

• Journal of Animal Environmental Science
• /
• v.2 no.1
• /
• pp.13-25
• /
• 1996

This study was conducted to analyze the technological levels of the domestic industries manufacturing the machinery and equipment for livestock production facilities and to lay out a scheme for upgrading the technical improvement. The results of this study are as follows : 1 . According to the study results, the technological levels of the domestic industries for livestock production facilities lag far behind those of the advanced countries in this field. 2. It was found that the ratio engaged in the areas of R&D was 10.7% and lower than that engaged in the other areas and the ratio of junior college graduated engineers engaged in the areas of research and design was 44.4%. Therefore, the amounts of investment for the areas of R&D and design should be increased. 3. In the design area, it was found from the study that the most weakness technologies which should be developed in near future were the universal harvester and the mechanical designing. Therefore, the multipurpose universal harvester suitable to the domestic farmland conditions should be developed and strength, hardness, and durability of materials in the mechanical designing should be improved.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.1
• /
• pp.72-79
• /
• 2022

Piezoelectric energy harvesting technologies, which can be used to convert the electricity from the mechanical energy, have been developed in order to assist or power the wearable electronics. To realize non-toxic and biocompatible electronics, the lead-free (Ba_0.85Ca_0.15)(Ti_0.90Zr_0.10)O₃ (BCTZ) nanoparticles (NPs) are being studied with a great attention as flexible energy harvesting device. Herein, piezoelectric hybrid nanocomposites were fabricated using BCTZ NPs-embedded poly(vinylidene fluoride-trifluoroethylene) [P(VDF-TrFE)] matrix to improve the performance of flexible energy harvester. Output performance of the fabricated energy device was investigated by the well-optimized measurement system during the periodically bending and releasing motions. The generated open-circuit voltage and the short-circuit current of the piezoelectric hybrid nanocomposite-based energy harvester reached up to ~15 V and ~1.1 ㎂, respectively; moreover, the instantaneous power of 3.5 ㎼ is determined from load voltage and current at the external load of 20 MΩ. This research is expected to cultivate a new approach to high-performance wearable self-powering electronics.

• Korean Journal of Materials Research
• /
• v.33 no.7
• /
• pp.295-301
• /
• 2023

Thermoelectric (TE) energy harvesting, which converts available thermal resources into electrical energy, is attracting significant attention, as it facilitates wireless and self-powered electronics. Recently, as demand for portable/wearable electronic devices and sensors increases, organic-inorganic TE films with polymeric matrix are being studied to realize flexible thermoelectric energy harvesters (f-TEHs). Here, we developed flexible organic-inorganic TE films with p-type Bi_0.5Sb_1.5Te₃ powder and polymeric matrices such as poly(3,4-eethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) and poly (vinylidene fluoride) (PVDF). The fabricated TE films with a PEDOT:PSS matrix and 1 wt% of multi-walled carbon nanotube (MWCNT) exhibited a power factor value of 3.96 µW·m^-1·K^-2 which is about 2.8 times higher than that of PVDF-based TE film. We also fabricated f-TEHs using both types of TE films and investigated the TE output performance. The f-TEH made of PEDOT:PSS-based TE films harvested the maximum load voltage of 3.4 mV, with a load current of 17.4 µA, and output power of 15.7 nW at a temperature difference of 25 K, whereas the f-TEH with PVDF-based TE films generated values of 0.6 mV, 3.3 µA, and 0.54 nW. This study will broaden the fields of the research on methods to improve TE efficiency and the development of flexible organic-inorganic TE films and f-TEH.

• Land and Housing Review
• /
• v.7 no.4
• /
• pp.307-314
• /
• 2016

Energy harvesting technique is to utilize energy that is always present but wasted. In this study, we have developed the energy harvester of the hybrid method utilizing both vibration and pressure of the vehicle traveling a road or parking lot. In the previous study, we have developed a prototype energy harvester, improved hybrid energy harvester, and developed a final product that offers improved performance in the hybrid module. The results were published in the previous paper. In this study, we installed the finally developed hybrid module in the actual parking lot. And we measured the power generation performance due to pressure and vibration, and the running speed of the vehicle when the vehicle is traveling. And we compared the results with those obtained in laboratory conditions. In a previous study performed in laboratory conditions the maximum power of the energy block was 1.066W when one single time of vibration, and 1.830W when succession with 5 times. On the other hand, in this study, we obtained the average power output of 0.310W when the vehicle is running at an average 5 km/h, 0.670W when at an average 10 km/h, and 1.250W when at an average 20 km/h, and 2.160W when at an average 5 km/h. That is, the higher the running speed of the vehicle has increased power generation performance. However, when compared to laboratory conditions, the power generation performance of the energy block in driving speed by 20km/h was lower than those in laboratory conditions. In addition, when compared to one time of vibration of laboratory conditions, power generation performance was higher when the running speed 20km/h or more and when five consecutive times in laboratory conditions, it was higher when the running speed 30km/h or more. It could be caused by a difference of load conditions between the laboratory and the actual vehicle. Thus, applying the energy block on the road would be more effective than that on the parking lot.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.227-228
• /
• 2016

본 논문에서는 압전소자를 이용한 에너지 하베스터의 전기적 모델링을 제안하였고 이를 시뮬레이션 및 실험을 통해 비교 분석하였다. 에너지 하베스터는 압전소자를 이용한 발전기, 풀브리지 정류기, 평활용 콘덴서, 부하로 구성된다. 본 논문에서는 에너지 하베스팅 방법으로 Standard AC 방법과 이에 풀브리지 정류기를 추가한 Standard DC 방법을 사용하였고 전기적 모델링, 시뮬레이션, 실험의 분석을 위해 압전 발전기를 RLC 등가모델로 구성하였다. 에너지 하베스터 실험장치를 구성하였으며, 두 가지의 전력변환 기법 각각 $73.7{\mu}W$, $69.3{\mu}W$를 하베스팅 하는 것을 확인하였다.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1999.07a
• /
• pp.71-76
• /
• 1999

우리나라의 마늘ㆍ양파의 재배면적은 '98년 현재 37,337㏊, 14,806㏊이고 생산량은 각각 39만여톤, 87만여톤으로 밭작물 중에서 큰 비중을 차지하고 있으나 수확작업의 대부분이 인력에 의하여 이루어지고 있기 때문에 생산비가 높고 수입품과의 가격차이가 심하여 재배농가에 큰 부담이 되고 있다. 한편 마늘ㆍ양파의 기계화작업이라야 경운정지, 방제, 비닐피복 등에 그치고 있고 일부지역에서 마늘 수확시 굴취기를 사용하고 있는 실정이다. 더욱이 논에서 마늘ㆍ양파를 재배할 경우 수확시기와 벼농사의 이앙시기가 이어지기 때문에 적기에 빠른 수확이 가능한 수확기의 개발이 요구되고 있다. (중략)