• 융복합기술연구소 논문집
• /
• 제12권1호
• /
• pp.7-12
• /
• 2022

The reduction ratio of the magnetic gear is determined by the ratio of the number of poles between the high-speed permanent magnet layer and the low-speed permanent magnet layer. In general, it is known that the greater the least common multiple of both poles, the smaller the torque ripple called by cogging of the magnetic force generated in the magnetic gear. However, little is known about the effect of the harmonic modulator that filters the magnetic field in the magnetic gear to magnetically couple the high-speed side and the low-speed side except for the number of poles. In this study, torque ripple characteristics according to changes in modulator shape such as opening ratio and tooth thickness are analyzed using a finite element analysis tool.

• 한국생산제조학회지
• /
• 제24권3호
• /
• pp.348-354
• /
• 2015

Using a magnetic gear, the speed and torque of the driving axis can be decreased and increased, respectively, similar to a mechanical speed reducer. In particular, because the driving side can be isolated mechanically from the load side, the magnetic gear was developed for application with environmental constraints. Of the existing topologies used for the magnet gear, the filtering method of a specified magnetic component is the most competitive. In this paper, a novel unified harmonic modulator is applied to filter the specified component. The torque conversion method using this modulator is described in detail, and the key factors of the modulator are derived from the influence on the resulting torque. The experimental setup was constructed and its torque transmission efficiency measured for varying loads. The transient characteristic from an excessive load is compared with the theoretical simulation.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 C
• /
• pp.1577-1579
• /
• 1994

200-MW pulse modulators(total 11units) for the PLS linac employ the SCR phase control circuit. It controls 3-phase AC line voltage for the high-voltage DC power supply (DCPS, maximum of 25kVDC, 4.2A) which charges the pulse forming network(PFN). The PFN delivers 400kV, 500A, ESW $7.5{\mu}s$ pulse power to the 80-MW klystron amplifier tube. The SCR regulates 3-phase AC power and feeds to the high voltage transformer. Two different types of the transformer configurations namely ${\Delta}-{\Delta}$ and ${\Delta}-Y$, are alternatively installed to 11 modulator units for the suppression of harmonic noises. RC filters and reactors are also installed. Currently, approximately 110-kW of average AC power per unit is consumed at the normal operation level of the modulator with 30pps. This paper presents the operational characteristics of the high power pulse modulator, especially the experimental results of the AC line harmonic components generated by the operation of the high power pulse modulator to suppress the switching noises from the SCR and rectifying diode arrays.

• 한국항행학회논문지
• /
• 제10권1호
• /
• pp.41-47
• /
• 2006

본 논문에서는 2차 고조파 발생기에서 발생되는 2차 고조파 성분을 추출하여, 그 신호와 주 신호를 동 위상 변조시키는 전치 왜곡 선형화 방법을 제시하였다. 고조파 발생기에서 추출한 고조파 성분의 동 위상과 직각 위상 성분 신호로 분리하여 그것의 크기만을 제어하여 전력증폭기의 혼변조 신호를 제거하는 방법으로 셀룰라대역에서 동작하는 회로를 구현하였으며, 그 결과 전력증폭기의 혼변조 신호 억압 특성을 확인하였다. 반송파 2톤 신호를 인가하였을 때, 주파수 간격이 ${\Delta}f$=1MHz에서 3차 혼변조 신호는 20dB 개선되었고, IS-95 CDMA 1FA 신호에서는 인접채널 전력비가 7dB 개선됨을 확인하였다.

• 대한전자공학회논문지TC
• /
• 제39권9호
• /
• pp.28-34
• /
• 2002

본 논문에서 제시한 새로운 형태의 전치왜곡 회로는 Harmonic Generator에서 발생되는 저주파 혼변조 신호 성분만을 추출하여, 이것을 Vector Modulator에서 원 신호와 진폭 변조시키는 것이다. 이러한 회로를 이용하여 3차, 5차 혼변조 신호를 발생시켜 전력 증폭기의 혼변조 신호를 감쇠시키는 선형화기를 구현하였다. 구현된 전치왜곡 선형화기는 국내 개인 휴대 통신(PCS) 기지국 송신 대역인 1840MHz~1870MHz주파수에서 동작되도록 제작, 측정을 하였다. 그 결과 반송파 2-tone 신호를 인가할 때 3차 혼변조 왜곡 특성은20dB 이상, 5차 혼변조 왜곡 특성은 10dB 이상의 개선효과를 얻었고, IS-95 CDMA 신호를 인가하였을 때 인접채널 전력 비를 10dB이상 개선시켰다.

• 융복합기술연구소 논문집
• /
• 제4권2호
• /
• pp.11-15
• /
• 2014

Magnet gear transfers a high speed torque of the driving side to a low speed following side. Of course, the torque is amplified as much as a ratio between pole number of magnet gears constituting both sides through ferromagnet modulator. However, the parameters of the overall magnetic system influence the transmitting torque strongly. They include a pole number of permanent magnet, magnet thickness, reducing ratio, harmonic modulator thickness, and open ratio etc. In this paper, the influences of the parameters are analyzed using finite element method tool. By comparison, a desirable design specification is proposed, including a recommended modulator pattern.

• Journal of information and communication convergence engineering
• /
• 제6권2호
• /
• pp.192-197
• /
• 2008

High-speed harmonic optical modulation-demodulation schemes are presented and a possibility of the schemes for applying to high-speed light wave transmission system is tested at microwave frequency range. An example of this concept is as follows : Light wave is modulated succeedingly through cascaded optical modulators by a sub-carrier to produce a modulated light wave at harmonic frequency which is higher than the feasible frequency of the individual modulators. For demodulation of the base-band signal, the high frequency optical sub-carrier is down-converted by the same kind of optical modulator with the same concept of harmonic modulation.

• 대한전자공학회논문지
• /
• 제25권1호
• /
• pp.42-48
• /
• 1988

MM(multimode) PWM(pulse width modulation) Suitable for high performance and harmonic effects minimization of VSI (voltabge source invertetr)-IM (induction motor)drive system is proposed. The approximated optimal, suboptimal and optimal PWM are implemented in the low frequency range, while square wave operation is realized in the hibh frequency range. The pulse width Modulator is capable of generating control signals to a transistorized inverter operating at about 1KHz. All functions except digital comparison have been implemented in softyware making the scheme economical, flexible and reliable. Pulse width modulator is built and tested experimentally. In order to confirm the effectiveness and the reliability of the theoretical proposition, this scheme is applied to 1Hp, Three phase IM. As results, it is concluded that the scheme of MM PWM is superior to other conventional switching scheme through the discussions or analysis carried out on the items such as line-to-line voltage, current and spectrum of current harmonic components observed at the output terminal of inverter, noise level of motor.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2006년도 하계종합학술대회
• /
• pp.203-204
• /
• 2006

We present and demonstrate a novel method of alternate-phase return-to-zero (RZ) signal generation and pulse-amplitude equalization simultaneously in a rational harmonic mode-locked fiber ring laser, using a dual-drive Mach-Zehnder (MZ) modulator. By adjusting the voltages applied to both arms of the modulator, the rational harmonic mode-locked pulse trains are equalized in their amplitudes. In addition to that, the amplitude-equalized pulse trains multiplying the repetition rate at ${\sim}10\;GHz$ have alternate $\pi$ phase difference between adjacent pulses. The alternate-phase RZ signal generated by the proposed method enhances transmission performance through the single-mode fiber (SMF) links without dispersion compensation.

• Journal of Power Electronics
• /
• 제16권1호
• /
• pp.388-397
• /
• 2016

An error-compensated pulse width modulator (ECPWM) is proposed to improve the baseband harmonic performance and the switching loss of voltage source inverters (VSIs). Selecting between harmonic distortion and switching loss is a design tradeoff in the conventional space vector pulse width modulation. In this work, an accumulated difference in produced and desired phase voltages is considered to adjust the reference signal. This mechanism can compensate for the voltage error in the previous carrier period. With error compensation every half-carrier period, the proposed ECPWM allows one-half reduction in carrier frequency without scarifying baseband harmonic distortion. The proposed modulator is applied to a three-phase VSI with R-L load and a motor-speed-control system for experiments. The measured efficiency and operating temperature of switches confirm the effectiveness of the proposed scheme.