• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.166-168
• /
• 2004

Conventional Switched Mode Power Supplies(SMPS) with diode-capacitor rectifier have distorted input current waveform with high harmonic order contents. Typically, these SMPS have a power factor lower than 0,7. To improve with this problem the power factor correction(PFC) circuit of power supplies has to be introduced. Specially, to the reduce size and manufacture cost of power conversion device, the single-stage PFC converter is increased to demand as necessary of study. In this paper, comparative analysis of Valley-fill, boost and feedforward type single stage power factor correction circuit based on the flyback converter is given. Also, the validity of designed three type of single stage PFC circuit are confirmed by simulation and experimental results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 추계학술대회 논문집 학회본부
• /
• pp.630-633
• /
• 1997

This paper describes a design of a single phase PWM converter for high speed train. Parallel operation and control method of four Quadrant PWM converters are described. Simulation and modelling of the converters is performed. Capacity of the converter/inverter and power circuit for high speed traction system designed. And harmonic contents of AC line current's are analyzed. The results of the simulation are presented.

• 한국초전도ㆍ저온공학회논문지
• /
• 제12권4호
• /
• pp.24-30
• /
• 2010

The renewable energy source is considered as a good measure to cope with the global warming problem and the fossil energy exhaustion. The construction of electric power plant such as an offshore wind farm is rapidly increasing and this trend is expected to be continued during this century. The bulky and long distance power transmission media is essential to support and promote the sustainable expansion of renewable energy source. DC power cable is generally considered as the best solution and the demand for DC electric power has been rapidly increasing. Especially, the high temperature superconducting (HTS) DC cable system begins to make a mark because of its advantages of huge power transmission capacity, low transmission loss and other environmental friendly aspects. Technical contents of DC HTS cable system are very similar to those of AC HTS cable system. However the DC HTS cable can be operated near its critical current if the heat generation is insignificant, while the operating current of AC HTS cable is generally selected at about 50~70% of the critical current because of AC loss. We chose the specifications of the cable core of 'Tres Amigas' project as an example for our study and investigated the heat generation when the DC HTS cable operated near the critical current by some electric and thermal analyses. In this paper, we listed some technical issues on the design of the DC HTS cable core and described the process of the cable core design. And the results of examination on the current capacity, heat generation, harmonic loss and current distribution properties of the DC HTS cable are introduced.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 B
• /
• pp.1126-1128
• /
• 2002

In proportion to the development of various cultural contents industry, although the lighting tools with advanced control system are needed, the fields of the lighting tools are not competitive in techniques because they are limited in small businesses and have been lost their markets to foreign companies in the high value added industry. Accordingly, the technique that is better than current lighting tools is needed urgently. So, for the new lighting tools, this paper presents a new dimming method using IGBT(Insulated Gate Bipolar Transistor) devices. There are three procedures in this study. For the first, the authors verify superiority of IGBT Dimmer with simulation using EMTDC in former step for development of IGBT dimmer. Secondly, the authors made IGBT dimmer directly with the basis of simulation results. For the last, the efficiency, the Total Harmonic Distortion(THD) current, temperature characteristic, noise characteristic, voltage drop, heat losses between the IGBT dimmer and the Thyristor dimmer that is being used popularly in the industries the stages, and the theaters were tested and compared..

• Journal of Electrical Engineering and Technology
• /
• 제12권3호
• /
• pp.1090-1100
• /
• 2017

This paper presents the comparison of starting current characteristics of a three-phase induction motor fed by two types of soft starters. The first soft starter under investigation is a conventional AC voltage controller on the basis of a phase-control technique. The other is the proposed asynchronous PWM AC chopper which is developed from the conventional synchronous PWM AC chopper. In this paper, the proposed asynchronous PWM AC chopper control scheme is developed by generating only two asynchronous PWM signals for a three-phase main power circuit (6 switching devices) from a single voltage control signal which is compared with a single sawtooth carrier signal. By this approach, the PWM signals are independent and easy to implement since the PWM signals do not need to be synchronized with a three-phase voltage source. Details of both soft starters are discussed. The experimental and simulation results of the starting currents are shown. It is found that the asynchronous PWM AC chopper efficiently works as a suitable soft starter for the three-phase induction motor due to that the starting currents are reduced and are sinusoidal with less harmonic contents, when being compared with the starting current waveforms using the conventional phase-control starting technique. Also the proposed soft starter offers low starting electromagnetic torque pulsation.

• 전기전자학회논문지
• /
• 제22권3호
• /
• pp.759-766
• /
• 2018

This paper presents a high-speed axial-flux machine which utilizes the idea of sinusoidal shaped pole combined with a consequent iron-pole. The target of the proposed machine is the cost reduction of the relatively expensive Samarium-Cobalt (SmCo) permanent magnet (PM) material and the torque per PM volume improvement by using sinusoidal consequent-pole rotor. The effectiveness of the proposed machine is validated by comparing it with conventional consequent-pole and with conventional PM machines using 3-D finite element method (FEM) simulations. The comparison and analysis is done in terms of back electro-motive force (back-EMF) harmonic contents, torque per PM volume and torque ripple characteristics. The simulation results show that the proposed machine is suitable and cost-effective for high-speed and high torque per PM volume applications. Furthermore, due to the consequent pole, the magnetic flux saturation and the overload current torque-capability are also presented and discussed in the paper.

• 한국콘텐츠학회논문지
• /
• 제16권4호
• /
• pp.604-613
• /
• 2016

지구온난화로 인한 바닷물의 열팽창, 빙하의 해빙 등으로 지구의 해수면은 매년 약 2.0mm/yr의 속도로 상승하고 있다. 그러나 해안에 인접한 하천을 설계할 시 기준이 되는 외수위는 과거 관측된 조위 값으로부터 4대 분조 및 조화상수를 분석하여 결정된다. 따라서, 외수위는 구조물의 설계빈도에 상응하는 해수면의 상승속도를 감안해야 할 필요가 있다고 사료된다. 본 연구에서는 국립해양조사원에서 운영하고 있는 47개소의 조위관측소를 대상으로 관측개시일부터 2015년까지 시단위로 조위자료를 수집하였다. 우리나라를 크게 서해, 남해, 동해, 제주 총 4개의 해역으로 구분하여 연별 변동추이 및 연평균 상승률 분석을 수행하였다. 그리고 기존 설계된 해안에 인접한 하천의 외수위를 검토하였다. 추후 국지적 해수면상승의 원인규명 및 외수위 고려 시 기초자료로 활용될 것으로 판단된다.

• Nuclear Engineering and Technology
• /
• 제18권1호
• /
• pp.1-8
• /
• 1986

SNU 1.5MV 반데그라프 가속기의 표적상자 전단에서 사용될 자기 4극 렌즈를 제작하고 그 광학적 특성을 측정 및 분석하였다. 렌즈의 칫수는 자극 길이 180mm, 구경 반경 25mm, 자극편 반경 28.75mm이며 자극과 철심의 재료로는 탄소강 KS-SM40C를 사용하였다. 코일은 자극 당 480회 감아 공냉식을 채택하고 있다. 제작한 렌즈에 직류 전류 2.99$\pm$0.03A를 흘리며 Hall 탐침소자를 써서 r,$\theta$,z의 각 방향에 대해 여러 지점에서 자장 요소 $B_{\theta}$, $B_{\gamma}$을 측정하였다. 측정된 자료에 대한 면적 적분과 직교성 다항함수 fitting을 통하여 렌즈 중심에서 자장 구배 G=566.3$\pm$2.1 gauss/cm, 렌즈축 상에서 유효길이 L=208.3$\pm$1.44mm로 나타났다. 렌즈의 다극 요소는 최소자승법을 써서 20극까지 결정하였다. 결과로서 렌즈 중심의 18mm 반경 이내의 영역에서 6극 요소 대 4극 요소의 비는 1.4$\pm$0,9% 이하이고, 기타 다극 요소들은 모두 0.5% 미만임을 얻었다.