• 한국통신학회논문지
• /
• 제24권6B호
• /
• pp.1183-1190
• /
• 1999

본 논문에서는 MPEG-2 비디오 인코더를 ASIC 칩으로 구현할 때, 움직임추정기와 함께 대량의 하드웨어 영역을 차지하는 프레임메모리 인터페이스를 개선한 효율적인 구조를 제시한다. 이를 위해 비디오 인코더와 듀얼 뱅크를 가지는 외부 SDRAM 사이의 인터페이스를 효율적으로 처리할 수 있도록 메모리 맵을 구성하고 메모리 액세스 타이밍을 최적화하여 내부 메모리 크기와 인터페이스 로직을 줄였다. 본 설계에는 0.5 m, CMOS, TLM(Triple Layer Metal) 표준 셀 라이브러리가 사용되었으며, 하드웨어 설계 및 검증을 위해서 VHDL 시뮬레이터와 로직 합성툴이 사용되었고, 기능 검증을 위한 테스트 벡터 생성을 위해서, C 언어로 모델링한 하드웨어 에뮬레이터가 사용되었다. 개선된 프레임 메모리 인터페이스의 구조는 기존의 구조[2-3]에 비해 58% 정도의 면적이 감소했으며, 전체 비디오 인코더에 대해서는 24.3% 정도의 하드웨어 면적이 감소되어, 프레임메모리 인터페이스가 비디오 인코더 전체의 하드웨어 면적에 대단히 심각한 영향을 미친다는 것을 결과로 제시한다.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제49권6호
• /
• pp.322-329
• /
• 2000

BIST(Built-in Self Test) has been considered as the most promising DFT(design-for-test) scheme for the present and future test strategy. The most serious problem in applying BIST(Built-in Self Test) into a large circuit is the excessive increase in test time. This paper is focused on this problem. We proposed a new BIST construction scheme which uses a parallel divide-and-conquer method. The circuit division is performed with respect to some internal nodes called test points. The test points are selected by considering the nodal connectivity of the circuit rather than the testability of each node. The test patterns are generated by only one linear feedback shift register(LFSR) and they are shared by all the divided circuits. Thus, the test for each divided circuit is performed in parallel. Test responses are collected from the test point as well as the primary outputs. Even though the divide-and-conquer scheme is used and test patterns are generated in one LFSR, the proposed scheme does not lose its pseudo-exhaustive property. We proposed a selection procedure to find the test points and it was implemented with C/C++ language. Several example circuits were applied to this procedure and the results showed that test time was reduced upto 1/2151 but the increase in the hardware overhead or the delay increase was not much high. Because the proposed scheme showed a tendency that the increasing rates in hardware overhead and delay overhead were less than that in test time reduction as the size of circuit increases, it is expected to be used efficiently for large circuits as VLSI and ULSI.

• 대한전기학회논문지
• /
• 제35권10호
• /
• pp.458-464
• /
• 1986

This paper introduces a method for design verification and performance evaluation of flight control system. The method is a real time hardware in the loop simulation using the hybrid computer and motion table facility. As a typical illustration, a roll control system of flight vehicle is applied. The simulation validity is demonstrated by comparing hardware test results with analog simulation results.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.969-973
• /
• 2005

This paper presents a survey of software reliability modeling and it's application to pre-built software system combined with hardware such as numerical controller based on personal computer systems. Many a systems in these days are much more becoming software intensive and many software intensive systems are safety critical. For this reason, the technique well developed to measure of software reliability is very important for whom to assess such a system. This paper provides a brief idea of method to evaluate such a system's reliability based on hardware performance.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1993년도 한국자동제어학술회의논문집(국내학술편); Seoul National University, Seoul; 20-22 Oct. 1993
• /
• pp.466-470
• /
• 1993

A HILS(Hardware-In-the-Loop Simulation) technique for an IR guided weapon is proposed. The IR HILS facility functions as a testing unit for a missile guidance and control system to evaluate target acquisition, tracking, and countermeasure performance. The configuration of IR HILS facility, modeling technique of an IR environment including target, background and countermeasure, and test and evaluation procedure are included.

• 전자공학회논문지A
• /
• 제32A권5호
• /
• pp.749-758
• /
• 1995

There are many testable design techniques, among which Scan path and BIST techniques are mainly used. In this paper, the increase of design effectiveness is discussed, when these techniques are applied to the practical implementation of chips. The following techniques are presented : 1) Blocks are commonly used to reduce test time without hardware increase, 2) MUX is used to implement the shortest Scan path, 3) Scan register is used which controls and/or observes several blocks to avoid the increase of hardware.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 A
• /
• pp.425-433
• /
• 1999

This paper describes a simulation model and a scaled hardware model to analyze the dynamic performance of Unified Power Flow Controller, which can flexibly adjust the active and reactive power flow through the ac transmission line. The design of control system was developed using vector control method. The results of simulation and scaled hardware test show that the developed control system works accurately. And both models are very effective to analyze the dynamic performance of the Unified Power Flow Controller.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 D
• /
• pp.2659-2661
• /
• 2002

The development of guided missile requires complex guidance schemes and hardware units because of high maneuver, delicate and variable missions. In this point of view, simulation systems and facilities which test missile hardwares and softwares are needed. This paper introduces the hardware-in-the loop simulation system and facilities which include the real-time computation systems and 3 Axis FMS(Flight Motion Simulator).

• 한국군사과학기술학회지
• /
• 제5권2호
• /
• pp.132-148
• /
• 2002

In this paper, development procedures of an Underwater Vehicle HILS/MILS System in SE(Synthetic Environment) are described. As this System is developed, we can obtain the more powerful tool which can be used to test and verify operational logics and algorithms of an Underwater Vehicle as well as its hardware in various tactical situations.

• 한국방송∙미디어공학회:학술대회논문집
• /
• 한국방송∙미디어공학회 2020년도 추계학술대회
• /
• pp.241-243
• /
• 2020

The high computational complexity of deep learning algorithms has led to the development of specialized hardware architectures. However, soft errors (bit flip) may occur in these hardware systems due to voltage variation and high energy particles. Many error correction methods have been proposed to counter this problem. In this work, we analyze an error correction mechanism based on repetition codes and an activation function. We test this method by injecting errors into weight filters and define an ideal error rate range in which the proposed method complements the accuracy of the model in the presence of error.