• 한국세라믹학회지
• /
• 제50권1호
• /
• pp.25-30
• /
• 2013

The pore volume of hardened cement with waterproofing materials is lower compared to that of hardened cement without waterproofing materials. Thus, fewer gaps will appear by means of chemical reactions between $Ca^{2+}$ ions in hardened cement and water, solutes, and other ions. Due to the selective permeability, the osmotic pressure of hardened cement can change due to physical effects such as the reduction of the pore volume and the reduction in the number of pores, as well as by the electrochemical reaction between water, solutes, other ions and $Ca^{2+}$ ions in hardened cement. Of course, these factors do not have independent effects but instead a combined complex effect. Accordingly, we studied changes in the osmotic pressure due to the difference in the pore structure of hardened cement. A pore size smaller than 1 nm in hardened cement had only a slight effect on the osmotic pressure, whereas a pore size larger than 1 nm had a direct effect on the osmotic pressure.

• 한국세라믹학회지
• /
• 제24권3호
• /
• pp.282-288
• /
• 1987

Diffusion of Cl- ion in hardened cement paste with slag and siliceous powder such as silica fume and white carbon was investigated. The addition of admixtures reduces the content of Ca(OH)2, which is the main cause of pore formation by corrosive action of sea-water. The addition of admixtures makes the hardened cement paste dense, thereby restricting the diffusion of Cl- ion and improving the resistance to sea-water. Apparence diffusion coefficient of Cl- ion in hardened ordinary portland cement paste was 3.7${\times}$10-8$\textrm{cm}^2$/sec, while that for the hardened cement paste with the admixture was 1.2∼3.2${\times}$10-8$\textrm{cm}^2$/sec.

• 한국세라믹학회지
• /
• 제26권5호
• /
• pp.698-704
• /
• 1989

Basic investigation for the flexural strength and water stability of hardened cement pastes using ordinary portland cement with water-soluble polyer (hydroxypropyl methyl cellulose ; HPMC) was carried out with 0.2 of water cement ratio. For molding of the specimen, the paste was mixed by twin roll mill. According to increase in the content of HPMC, the setting time of cement paste was delayed and the flexural strength was increased. The maximum flexural strength of hardened cement paste with 5.0wt% of HPMC was about 330 kg/$\textrm{cm}^2$. The expansion of the hardened cement paste immersed in water was increased with the content of water soluble polymer(HPMC). Consequently, the strength and the water stability of the hardened cement pastes were remarkably reduced by the expansion of them.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.810-813
• /
• 2004

Air void systems in hardened concrete has an important influence on concrete durability such as freeze-thaw resistance, water permeability, surface scaling resistance, and etc. Linear traverse method and point count method described at ASTM have been widely used to estimate the air void system in hardened concrete. These methods, however, are rarely used at present, because they require many efforts, are time consuming works, depend on each person's decision, and are not repeatable. Thus, new image analysis method using microscope and computer processes has been approached for analyzing air void system in hardened concrete. However, it is just in initial step. The purposes of this study were to develope an effective and reliable image analysis technique for estimating air void system in hardened concrete. The developed technique was proved to be accurate, reasonable and repeatable.

• 한국안전학회지
• /
• 제23권1호
• /
• pp.18-23
• /
• 2008

The abnormal wears such as unfair-wear and early-wear happen in the earn shaft surface of automobiles. These abnormal wears make efficiency of engines decrease and threaten safety of automobiles. The wear characteristics of the cam shaft is very important for the automobile safety. The cam shaft is surface-hardened by the high frequency induction. In this study, we investigated the wear characteristics of the hardened surface with a SM53C steel. The wear characteristics is examined according to the hardened depth and the amount of load.

• 한국자동차공학회논문집
• /
• 제6권1호
• /
• pp.134-142
• /
• 1998

The effects of small hole defect size and effective case depth(ECD) on the four point bending fatigue limit of induction surface hardened S45C steel were investigated the fatigue limit evaluation of hardened materials is very difficult because of relations of the hardness gradient and residual stress. In this study, it was possible to characterize fatigue limit and fatigue life of induction surface hardened S45C steel in terms of the hole defect size and effective case depth(ECD) and quantitative evaluation of the fatigue limit with hole defects use Murakami's evaluation method and the range of evaluated values is a good accuracy compared with results.

• 한국세라믹학회지
• /
• 제31권12호
• /
• pp.1507-1512
• /
• 1994

High strength cement hardened body was prepared by ordinary portland cement, silica-fume, super-plasticizer and the industrial by-product powder such as tailing, paper sludge ash and granulated slag. These raw materials were mixed and formed with w/c=0.18. The cement hardened body is cured in the autoclave at 18$0^{\circ}C$, 10atm. These admixtures made the compressive strength of all specimens develope by 170~230%. The highest compressive strength could be obtained by 236 MPa when mix composition was 14 wt% of silica-fume and 26 wt% of granulated slag. The compressive strength increased with decreasing the average pore size and the amount of the poe over the size of 50 nm by which the appearance of high compressive strength of the cement hardened body were mainly influenced. In the result, the hydration products were C-S-H, tobermorite and ettringite and it was realized that the reason why the cement hardened body became dense and revealed the higher strength was that those hydrates were formed inside of the pore and filled in it and the unhydrated materials played the role of an inner-filler.

• 한국기계가공학회지
• /
• 제6권3호
• /
• pp.16-23
• /
• 2007

An experimental investigation with diode laser system was carried out to study the effect of surface heat treatment on the die materials(SM45C, SKD11, SK3). The surface heat treatment characteristics of the laser beam are evaluated using hardness tests, optical microscopy, X-ray diffraction and energy dispersive X-ray spectroscopy(EDS). Results indicated that the beam size, focal length, feed rates are changed surface hardened characteristics. SM45C is higher hardness than other materials and composed to martensite grain at hardened zone, whereas other materials(SKD11, SK3)are low hardness than expected and composed to austenite and allayed martensite at hardened zone. The intensive X-ray diffraction patterns of (110)-(200)-(211) is detected hardened surface and the hardened surface distributed plenty of carbon density than metal zone.

• 대한기계학회논문집
• /
• 제19권8호
• /
• pp.1907-1914
• /
• 1995

An on-line measurement of the workpiece hardened depth in laser surface hardening processes is very much difficult to achieve, since the hardening process occurs in depth wise direction. In this paper, the hardened depth is estimated using a multilayered neural network. Input data of the neural network are the surface temperatures at arbitrary chosen five surface points, laser power and traveling speed of laser beam torch. To simulate the actual hardening process, a finite difference method(FDM) is used to model the process. Since this model yields the calculation results of the temperature distribution around the workpiece volume in the vicinity of the laser torch, this model is used to obtain the network's training data and laser to evaluate the performance of the neural network estimator. The simulation results show that the proposed scheme can be used to estimate the hardened depth with reasonable accuracy.

• 제어로봇시스템학회논문지
• /
• 제9권12호
• /
• pp.1048-1054
• /
• 2003

In laser surface hardening processes, the geometrical parameters such as the depth and the width of a hardened layer can be utilized to assess the hardened layer quality. However, accurate monitoring of the geometrical parameters for on-line process control as well as for on-line quality evaluation is very difficult because the hardened layer is formed beneath a material surface and is not visible. Therefore, temperature monitoring of a point of specimen surface has most frequently been used as a process monitoring method. But, a hardened layer depends on the temperature distribution and the thermal history of a specimen during laser surface hardening processing. So, this paper describes the estimation results of the geometric parameters using multi-point surface temperature monitoring. A series of hardening experiments were performed to find the relationships between the geometric parameters and the measured temperature. Estimation results using a neural network show the enhanced effectiveness of multi-point surface temperature monitoring compared to one-point monitoring.