• International Journal of Highway Engineering
• /
• v.15 no.1
• /
• pp.143-154
• /
• 2013

PURPOSES: Design of approach roads of rest areas in highway has many drawbacks such as geometric design elements. There has been traffic accidents occured in these approach roads of rest areas. Thus, design criteria is required in order to protect accidents from being occurred. In case of Korea, geometric structure design criteria of entry facilities, such as toll-gate, interchange, junction etc was established. However there are no presence in a detailed standards for geometric structure of the rest area which affiliated road facilities. METHODS: In this study, analytic on accidents was carried out in regards to the entry of geometric structure of resting areas by utilizing a sight survey and an investigation research of traffic accidents. The survey was targeting 135 general service areas. Collisions with physical channelization and safety facilities occurred due to speeding, rapid entry, and etc at the entrance nose section. At the entrance connector roads, accidents caused by speeding, negligence, over-operation of handle of drivers were main reason of accidents. Discriminant analysis were conducted about geometric elements to distinguish influencing factors for traffic accidents. the lengths and access angles of the entrance connector roads were regarded as to have the high relation with traffic accidents. RESULTS: After classifying the design section of resting areas' entry as well as derive design elements on each section, a speed measurement by targeting entry of rest areas and car behavior surveys were performed, then each element's minimum standard was derived through the analyses. According to the speeds at the starting/end point of entrance connector road, the range of the junction setting angle of the entrance connector road is defined as $12^{\circ}{\sim}17^{\circ}$ and the connector length model was suggested. CONCLUSIONS: Suggest improvement plans for existing rest areas that can be applied realistically. This should be corresponded to the standards of entry and exit of developed rest areas.

• Journal of Drive and Control
• /
• v.19 no.4
• /
• pp.19-28
• /
• 2022

This paper introduces an automatic steering system for straight traveling capable of being mounted on drivable agricultural machinery which user can handle it such as a tractor, a transplant, etc. The modular automatic steering device proposed in the paper is composed of RTK GNSS, IMU, HMI, hydraulic valve, and wheel sensor. The path generation method of the automatic steering system is obtained from two location information(latitude and longitude on each point) measured by GNSS in advance. From HMI, a straight path(AB line) can be created by connecting latitude and longitude on each point and the device makes the machine able to follow the path. During traveling along the reference path, it acquires the real time position data every sample time(0.1s), compares the reference with them and calculates the lateral deviation. The values of deviation are used to control the steering angle of the machine using hydraulic valve mounted on the axle of front wheel. In this paper, Pure Pursuit algorithm is applied used in autonomous vehicles frequently. For the analysis of traveling characteristics, field tests were executed about these conditions: velocity of 2, 3, 4km/h which is applied to general agricultural work and ground surface of solid(asphalt) and weak condition(soil) such as farmland. In the case of weak ground state, two experiments were executed about no-load(without work) and load(with work such as plowing). The maximum average deviations were presented 2.44cm, 7.32cm, and 11.34cm during traveling on three ground conditions : asphalt, soil without load and with load(plowing).

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2022.05a
• /
• pp.476-477
• /
• 2022

This study deals with rotation, which is one of the expression methods of motion used in the 3D development environment. Euler angle is a rotation method introduced by Leonhard Euler to display objects in three-dimensional space. Although three angles can handle all rotations in a three dimensional coordinate space, there are serious errors in this approach. If you rotate an object with Euler angles, you will face the problem of gimbal locks that cannot rotate under certain circumstances. In contrast to this, the method to rotate an object without a gimbal lock is the quaternion rotation with quaternion. Rather than a detailed mathematical proof of quaternion, it introduces what concept is used in the current 3D development environment, and applies it to camera rotation control to implement a rotating camera without a gimbal lock.

• Journal of Korean Society of Forest Science
• /
• v.53 no.1
• /
• pp.62-74
• /
• 1981

The developed record of forest maschines and tools in West Germany, Austria and Swiss, their technical characteristics and the working methods with them have been tried to investigate through the study of literature and observation. The aim of this investigation is to find out and introduce the technical information for training our forest men with them and for improving or developing our forest maschines and tools. Although ax chosen as first report for this aim is the oldest tool in the mankind history, still this is widely using in the forest work. And this has some special working filed that any other maschines could not overcome and sometimes should be recommended in the agronomical sideview. Through this investigation several points could be proposed as the technical informations when we will try to improve our ax 1. Radius of as-face curvature is proposed to be 150 mm and it's central point to be passed at one third point near to ax-eye. 2. Cutting angle is proposed to be $30^{\circ}$, ax-thick at 12 mm distance from ax-face to be 4 mm, thick at 30 mm distance from face to be 5 to 6 mm and ax-face width to be $125{\pm}5mm$. 3. Neck size is proposed to be $3.5{\pm}0.5{\times}5.5{\pm}0.5cm$ with a little curvature and neck thick from ax-house to be more than 1.5 cm. 4. Ax weight is proposed to be 1,000 gr with the stupid back and the sharp front. 5. The handle length of ax will be followed to the arm length of our forest workers.

• Geophysics and Geophysical Exploration
• /
• v.9 no.1
• /
• pp.102-107
• /
• 2006

Recently, rapid developments in computer hardware have enabled reverse-time migration to be applied to various production imaging problems. As a wave-equation technique using the two-way wave equation, reverse-time migration can handle not only multi-path arrivals but also steep dips and overturned reflections. However, reverse-time migration causes unwanted artefacts, which arise from the two-way characteristics of the hyperbolic wave equation. Zero-lag cross correlation with diving waves, head waves and back-scattered waves result in spurious artefacts. These strong artefacts have the common feature that the correlating forward and backward wavefields propagate in almost the opposite direction to each other at each correlation point. This is because the ray paths of the forward and backward wavefields are almost identical. In this paper, we present several tactics to avoid artefacts in shot-domain reverse-time migration. Simple muting of a shot gather before migration, or wavefront migration which performs correlation only within a time window following first arriving travel times, are useful in suppressing artefacts. Calculating the wave propagation direction from the Poynting vector gives rise to a new imaging condition, which can eliminate strong artefacts and can produce common image gathers in the reflection angle domain.

• Geophysics and Geophysical Exploration
• /
• v.19 no.4
• /
• pp.220-227
• /
• 2016

Marine seismic data have not only primary signals from subsurface but also ghost signals reflected from the sea surface. The ghost decreases temporal resolution of seismic data because it attenuates specific frequency components. For eliminating the ghost signals effectively, the exact ghost delaytimes and reflection coefficients are required. Because of undulation of the sea surface and vertical movements of airguns and streamers, the ghost delaytime varies spatially and randomly while acquiring seismic data. The reflection coefficient is a function of frequency, incidence angle of plane-wave and the sea state. In order to estimate the proper ghost delaytimes considering these characteristics, we compared the ghost delaytimes estimated with L-1 norm, L-2 norm and kurtosis of the deghosted trace and its autocorrelation on synthetic data. L-1 norm of autocorrelation showed a minimal error and the reflection coefficient was calculated using Kirchhoff approximation equation which can handle the effect of wave height. We applied the estimated ghost delaytimes and the calculated reflection coefficients to remove the source and receiver ghost effects. By removing ghost signals, we reconstructed the frequency components attenuated near the notch frequency and produced the migrated stack section with enhanced temporal resolution.

• Korean Journal of Occupational Therapy
• /
• v.26 no.4
• /
• pp.85-95
• /
• 2018

Objective : The purpose of this study was to investigate the awareness and availability on items of 2018 assistive devices distribution program for the disabled in the occupational therapists. Methods : A total of 132 occupational therapists participated in the survey from May 1 to May 31. Results : 96.2% of the occupational therapists responded that assistive device is helpful in lives of the disabled people. Especially, they responded that assistive device is the most helpful in 'movement and mobility'. Awareness on an angle spoon/fork with built-up handle and universal cuff was the highest, while a visual signaling indicator was the lowest. Availability on an air cushion was the highest, while a visual signaling indicator and a voice guidance system were the lowest. 67.4% responded that 'sometimes' they use the assistive device and 77.3% responded they will utilize the assistive device. To improve awareness and availability, 43.2% needed financial support, 32.6% needed to add insurance bill and 22.7% needed related education. Conclusion : In the future, this result will be available as a basic data for the education about assistive device for the occupational therapists.

• Journal of the Korea Society of Computer and Information
• /
• v.29 no.4
• /
• pp.63-72
• /
• 2024

The size of the home interior market is growing rapidly as interest in interiors and self-interiors has increased due to the recent rapid increase in single-person households. Most of the Bathroom remodeling is done by requesting an offline interior contractor and then visually checking it in the final completion stage, so it is not easy to re-construct even if the customer is dissatisfied. Therefore, this study developed an immersive virtual reality-based Bathroom self-remodeling system that can visually check space and design from the design stage to the final stage by incorporating VR technology to feel realistic in virtual reality. The bathroom structure may select the basic structure of the predefined bathroom space or freely set the size of the bathroom space. For furniture items, you can choose the washbasin, toilet, bathtub, shower booth that are essential elements of the bathroom and others(mounting rack, trash bin, handle). The tile texture may change the texture of the selected tile at a desired wall position by selecting various textures. In particular,, the texture of the wall tile can be varied by selecting horizontal, vertical and inclined directions at the desired angle according to the needs of the user and the contractor. As a future research project, this system will enable indoor sharing between users who are physically far away in real-time, allowing direct experience in virtual spaces, connection to purchases, and request estimates.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.17 no.2
• /
• pp.84-89
• /
• 2013

Purpose: Patients' movement during long image acquisition time for the fusion image of PET-CT (Positron Emission Tomography-Computed Tomography) results in unconformity, and greatly affects the quality of the image and diagnosis. The arm support fixtures provided by medical device companies are not manufactured considering the convenience and safety of the patients; the arm and head movements (horizontal and vertical) during PET/CT scan cause defects in the brain fundus images and often require retaking. Therefore, this study aims to develop patient-compensation device that would minimize the head and arm movements during PET/CT scan, providing comfort and safety, and to reduce retaking. Materials and Methods: From June to July 2012, 20 patients who had no movement-related problems and another 20 patients who had difficulties in raising arms due to shoulder pain were recruited among the ones who visited nuclear medicine department for PET Torso scan. By using Patient Holding System (PHS), different range of motion (ROM) in the arm ($25^{\circ}$, $27^{\circ}$, $29^{\circ}$, $31^{\circ}$, $33^{\circ}$, $35^{\circ}$) was applied to find the most comfortable angle and posture. The manufacturing company was investigated for the permeability of the support material, and the comfort level of applying bands (velcro type) to fix the patient's head and arms was evaluated. To find out the retake frequency due to movements, the amount of retake cases pre/post patient-compensation were analyzed using the PET Torso scan data collected between January to December 2012. Results: Among the patients without movement disorder, 18 answered that PHS and $29^{\circ}$ arm ROM were the most comfortable, and 2 answered $27^{\circ}$ and $31^{\circ}$, respectively. Among the patients with shoulder pain, 15 picked $31^{\circ}$ as the most comfortable angle, 2 picked $33^{\circ}$, and 3 picked $35^{\circ}$. For this study, the handle was manufactured to be adjustable for vertical movements. The material permeability of the patient-compensation device has been verified, and PHS and the compensation device were band-fixed (velcro type) to prevent device movements. A furrow was cut for head fixation to minimize the head and neck movements, fixing bands were attached for the head, wrist, forearm, and upper arm to limit movements. The retake frequency of PET Torso scan due to patient movements was 11.06% (191 cases/1,808 patients) before using the movement control device, and 2.65% (48 cases/1,732 patients) after using the device; 8.41% of the frequency was reduced. Conclusion: Recent change and innovation in the medical environment are making expensive medical image scans, and providing differentiated services for the customers is essential. To secure patient comfort and safety during PET/CT scans, ergonomic patient-compensation devices need to be provided. Therefore, this study manufactured a patientcompensation device with vertically adjustable ergonomic ROM according to the patient's body shape and condition during PET Torso scan. The defects in the basal ganglia images due to arm movements were reduced, and retaking was decreased.

• Journal of Biomedical Engineering Research
• /
• v.19 no.1
• /
• pp.69-80
• /
• 1998

This research was designed to investigate how the exercise program affects paraplegic standing and walking employing functional electrical stimulation(FES). Emphasis was also given to fatigue of major lower extremity muscles induced by different types of electrical stimulation. We applied continuous and intermittent rectangular pulse trains to quadriceps of 10 normal subjects and 4 complete paraplegic patients. The frequencies were 20Hz and 80Hz, and the knee angle was fixed at 90$^{\circ}$and 150$^{\circ}$to investigate how muscle fatigue is related to muscle length. The knee extensor torque was measured and monitored. We have been training quadriceps and gastrocnemius of a male paraplegic patient by means of electrical stimulation for the past two year. FES standing was initiated when the knee extensors became strong enough to support the body weight, and then the patient started FES walking utilizing parallel bars and a walker. We used an 8-channel constant-voltage stimulator and surface electrodes. The experimental results indicated that paralyzed muscles fatigued rapidly around the optimal length contrary to normal muscles and confirmed that low frequency and intermittent stimulation delayed fatigue. Our exercise program increased muscle force by approximately 10 folds and decreased the fatigue index to half of the initial value. In addition, the exercise enabled the patient to voluntarily lift each leg up to 10cm, which was of great help to the swing phase of FES walking. Both muscle force and resistance to fatigue were significantly enhanced right after the exercise was applied every day instead of 6 days a week. Up to date, the patient can walk for more than two and half minutes at 10m/min while controlling the on/off time of the stimulator by pushing the toggle switch attached to the walker handle.