• Journal of Sensor Science and Technology
• /
• v.29 no.5
• /
• pp.283-292
• /
• 2020

Current sensors that use a Hall element and Hall IC to measure the magnetic fields generated in steel silicon core gaps do not distinguish between direct and alternating currents. Thus, they are primarily used to measure direct current (DC) in industrial equipment. Although such sensors can measure the DC when installed in expensive equipment, ascertaining problems becomes difficult if the equipment is set up in an unexposed space. The control box is only opened during scheduled maintenance or when anomalies occur. Therefore, in this paper, a method is proposed for facilitating the safety management and maintenance of equipment when necessary, instead of waiting for anomalies or scheduled maintenance. A Bluetooth 4.0 low-energy current-sensor system based on near-field communication is used, which compensates for the nonlinearity of the current-sensor output signal using a piecewise linear model. The sensor is controlled using its generic attribute profile. Sensor nodes and cell phones used to check the signals obtained from the sensor at 50-A input currents showed an accuracy of ±1%, exhibiting linearity in all communications within the range of 0 to 50 A, with a stable output voltage for each communication segment.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.5
• /
• pp.74-83
• /
• 2009

Recently, usage of electric and electronic system for car increases rapidly. Consequently power monitoring supplied to the system is essential for management and controlling. Generally, battery status is monitored through measuring and diagnosing the current measurement method utilizing Hall Effect. Therefore, in this paper, we analysed magnetic field to develop the solution of DC current sensor using Hall Effect which is the core of design and development. By analysing the magnetic field by FEM using Maxwell 3D software, the location of the highest output current and stable part in the Hall IC sensor was shown. Also, the optimal core design of DC current sensor using parametric and Simplex method was presented. A car battery charge and discharge process dependant on time effect on the changing of magnetic field was simulated and compared to the result from the experiment result of actual vehicle.

• Journal of Sensor Science and Technology
• /
• v.25 no.5
• /
• pp.310-319
• /
• 2016

Three types of gap sensors, a capacitive gap sensor, an eddy current gap sensor, and a Hall effect gap sensor are described and evaluated through experiments for the purpose of precise gap sensing for micrometer scale movement, and a novel type of differential hall effect gap sensor is proposed. Each gap sensor is analyzed in terms of resolution and environment dependency including temperature dependency. Furthermore, a transport system for AMOLED deposition is introduced as a typical application of gap sensors, which are recently receiving considerable attention. Based on the analyses, the proposed differential Hall effect gap sensor is found to be the most suitable gap sensor for precise gap sensing, especially for application to a transport system for AMOLED deposition. The sensor shows resolution of $0.63mV/{\mu}m$ for the overall range of the gap from 0 mm to 2.5 mm, temperature dependency of $3{\mu}m/^{\circ}C$ from $20^{\circ}C$ to $30^{\circ}C$, and a monotonic characteristic for the gap between the sensor and the target.

• Korean Journal of Materials Research
• /
• v.4 no.1
• /
• pp.113-116
• /
• 1994

InSb thin film magnetic sensor, which have been prepared on glass substrate by vacuum evaporation, is investigated in this paper. The dependance of Hall voltage on magnetic field and temperature is examined by Hall effect. The variation of Hall voltage with magnetic field is almost linear at constant current drive but it is deviated from the linearity at constant voltage drive. Hall voltage decreases as the ambient temperature increases, so it is necessary to take into account the temperature effect when the InSb thin film is used as magnetic sensor.

• Journal of Power Electronics
• /
• v.9 no.1
• /
• pp.68-73
• /
• 2009

Automotive inverters may require current sensors for motor torque control, especially, in applications of hybrid electric vehicles or fuel cell vehicles. In this paper, to achieve a compact, integrated and low cost current sensor, a hall current sensor without magnetic core is introduced for integrating an automotive inverter. The compactness of the current sensor is possible by using integrated magnetic concentrators based on the Hall effect. Magnetic fields caused by three-phase currents are analyzed and a magnetic shield design is proposed for decoupling the cross-coupled field. It offers galvanic isolation, wide bandwidth (>100kHz), and accuracy(< 1%). Using 2D FEM analysis, its performance is demonstrated with design parameters at a U-shaped magnetic shield. The proposed coreless current sensor is tested with rated current to validate the linearity and accuracy.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.791-793
• /
• 1993

The hall sensor is current detector using hall effect in semiconductor and the conventional type detect current with concentrating flux by current of conductor. So, detection of small current is very difficult because of residual magnetism. This paper give the experiments based results about method that detect the small DC current using minimizing the residual of hall element by magnetic modulation and concentrating flux. The suggested sensor can dector small current better than the conventional that.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.66 no.2
• /
• pp.53-57
• /
• 2017

This papers propose a Hall-effect sensors position error compensation method in a sunroof system using a BLDC motor with a low-cost MCU. If the BLDC motor is controlled with this wrong position, the torque ripple and operating current can be increased and the average torque also decreases. Generally, sunroof system has characteristics that operate at constant load for several seconds. It is possible to find the minimum operating current value while changing the position of the Hall-effect sensor during the sunroof operation by using these characteristics. Therefore, propose a method to change the Hall-effect sensor position and find the minimum current value. The validity of the proposed algorithm is verified through experiments.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.2
• /
• pp.268-277
• /
• 1994

Current sensor using Hall device is an instrument of detecting a current by Hall effect. The existing current sensor is ordinarily worked by concentrating electromagnetism produced around the conducting wire turned iron core. The tiny curren, however, could not be accurately detected by the instrument owing to influence of residual magnetism exisisting in iron core, and the result of detecting is also somewhat on the large side. kAccordingly, We fabricated a new type of instrument minimizing the influence of residual magnetism existing in iron core and detected the tiny DC current accurately by taking advantage of magnetic modulation. The range of measuring DC current is 0[mA]-100[mA] and the maxiumm Linerity tolleance by the result of detecting current, can be reduced less than 3 percent.

• Journal of electromagnetic engineering and science
• /
• v.18 no.1
• /
• pp.35-40
• /
• 2018

This study presents a vertical-type CMOS Hall device with improved sensitivity to detect a 3D magnetic field in various types of sensors or communication devices. To improve sensitivity, trenches are implanted next to the current input terminal, so that the Hall current becomes maximum. The effect of the dimension and location of trenches on sensitivity is simulated in the COMSOL simulator. A vertical-type Hall device with a width of $16{\mu}m$ and a height of $2{\mu}m$ is optimized for maximum sensitivity. The simulation result shows that it has a 23% better result than a conventional vertical-type CMOS Hall device without a trench.

• International Journal of Advanced Culture Technology
• /
• v.3 no.1
• /
• pp.113-119
• /
• 2015

This paper presents a design and implementation of real time electrical energy computing tool to measure and record the electrical energy based on type of detection devices, Hall Effect current sensor and Microcontroller. The tool was installed on the system power supply of the room and compared with kWh meter. Finally, we found that the energy record has error of average power calculating results is 0.077%.