• Proceedings of the KIEE Conference
• /
• 1998.07a
• /
• pp.343-345
• /
• 1998

By computer simulation, the pattern of magnetic field distribution on the Nb-foil of a rotating flux type superconducting power supply has been calculated. Using the results, the current pumping rate has been calculated and compared with the results obtained by the experiment. The experiment has been executed with small-size flux-rump in the environment of LN2 and LHe in order to compare the pattern of magnetic filed in the superconducting state and in the normal state. Five hall-sensor was located on the center, right side, left-side, upper side, lower side of the Nb-foil in order to obtain more accurate pattern of the magnetic field generated by rotating pole. In the simulation, the effects of the excitation-magnet and the iron core located at the inner-side and circumference of the magnet have been considered. By comparing the data from the experiment and the results from the simulation, the size of normal spot estimated. At the same time, by calculating the linkage flux, the current-pumping-rate has been obtained. Consequently, the results obtained from experiment and simulation coincided as expected.

• Journal of IKEEE
• /
• v.17 no.2
• /
• pp.182-188
• /
• 2013

Using a ceramic target ZnO:In with In doping concentration of 2%, hetero-junctions of n-ZnO:In/p-Si and p-ZnO:(In, N)/n-Si were fabricated by depositing Indium doped n - type ZnO (ZnO:In or IZO) and Indium-nitrogen co-doped p - type ZnO (ZnO:(In, N)) films on wafers of p-Si (100) and n-Si (100) by DC magnetron sputtering, respectively. These films with the best electrical and optical properties were then obtained. The micro-structural, optical and electrical properties of the n-type and p-type semiconductor thinfilms were characterized by X-ray diffraction (XRD), RBS, UV-vis; four-point probe resistance and room-temperature Hall effect measurements, respectively. Typical rectifying behaviors of p-n junction were observed by the current-voltage (I-V) measurement. It shows fairly good rectifying behavior with the fact that the ideality factor and the saturation current of diode are n=11.5, Is=1.5108.10-7 (A) for n-ZnO:In/p-Si hetero-jucntion; n=10.14, Is=3.2689.10-5 (A) for p-ZnO:(In, N)/n-Si, respectively. These results demonstrated the formation of a diode between n-type thin film and p-Si, as well as between p-type thin film and n-Si..

• Journal of Korean Society of Archives and Records Management
• /
• v.18 no.4
• /
• pp.69-97
• /
• 2018

This study is a basic study for the comparison and analysis of the current status and service of the Unified Presidential Archives and the civilian memorial hall, which manages the country's presidential records. For this purpose, the Presidential Archives and individual private memorial halls were surveyed on the current status of records, online and off-line services, and legal and institutional records. Based on this, the study analyzed the characteristics and differences of the Unified Presidential Archives and individual private memorial halls. This study is meaningful in that it attempted to compare and analyze the characteristics of the Unified Presidential Archives and individual private memorial halls and that the two agencies sought basic research to develop cooperative relations.

• Fashion & Textile Research Journal
• /
• v.24 no.5
• /
• pp.557-566
• /
• 2022

This study aims to investigate Jinju silk companies, production items, and silk industry supporting projects from 2019 to 2021 in order to discuss the current status of the silk industry. The following are this study's methods: First, a list of Jinju silk companies that have been operating for the past three years (2019-2021) was prepared to investigate the current status of the Jinju silk industry. Second, an investigation was conducted into the representative products produced in Jinju over the past three years; this investigation was conducted using direct interview. Third, an investigation was conducted on the projects that supported the Jinju silk industry over the past three years, and the list of members of the Gyeongnam Textile and Jinju Silk Industry Cooperative Association-a facility of Gyeongsangnam-do Province, the Jinju City Hall brochure (2019), and the SMINFO(SMall business status INFOrmation System) were utilized for this purpose. The following are the results: First, Jinju silk companies are classified into four categories, namely weaving, dyeing, twisting, and designing companies. According to data from 2021, 83% (34 of 41) of silk companies were weavers. Second, the demand for solid fabrics has increased over the past three years. The demand for patterned jacquard fabrics in producing Hanbok and Western-style clothing has decreased. Third, support for the Jinju silk industry could be classified into five categories: support for the operation of silk research institutions, support for the diversification of Jinju silk, support for the promotion of Jinju silk, support for the operation of silk manufacturers, and others.

• Journal of the Korea Safety Management & Science
• /
• v.10 no.2
• /
• pp.169-174
• /
• 2008

In this study we develop core technology of Multi-Charmel Voice Guidance System based on active 2.45GHz RFID that can be used in the field of advertising. Through this, we can service more familiar with voice information to foreigners by own language in large scale international event. As an alternative to the current high-expensive voice guidance system in exhibition hall and provide more value added services to user. As the result, we present the configuration of integrated software platform which include media server, media client and receiver. It can be as a basis infra equipment for a signtseeing in RFID/USN environment. Additionally through tag information analysis about exposure of advertisement that is collected late, supposed system may achieve role as a new marketing tool.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.12
• /
• pp.2246-2253
• /
• 2011

This paper presents the error correction method of magnetic position sensor using recursive least square method (RLSM) with forgetting factor. Magnetic position sensor is proposed for linear position detection of the linear motor which has tooth shape stator, consists of permanent magnet, iron core and linear hall sensor, and generates sine and cosine waveforms according to the movement of the mover of the linear motor. From the output of magnetic position sensor, the position of the linear motor can be detected using arc-tan function. But the variation of the air gap between magnetic position sensor and the stator and the error in manufacturing process can cause the variation in offset, phase and amplitude of the generated waveforms when the linear motor moves. These variations in sine and cosine waveforms are changed according to the current linear motor position, and it is very difficult to compensate the errors using constant value. In this paper, the generated sine and cosine waveforms from the magnetic position sensor are compensated on-line using the RLSM with forgetting factor. And the speed observer is introduced to reduce the effect of uncompensated harmonic component. The approaches are verified by some simulations and experiments.

• Korean Journal of Environment and Ecology
• /
• v.20 no.3
• /
• pp.352-358
• /
• 2006

We reconsidered the taxonomy of lizards in Korea on the basis of morphological characters of collected specimens and previously published data. A total of 138 specimens were used in this study, which were collected from April 1996 to October 2005, From the observations, we presented keys to classify Korean lizards. Also, we indicated sampling sites for each species on the Korean map. In addition, we added some remarks on the distribution of Gekko japonicus, the study of genus Scincella and the synonym of genus Takydromus. Especially, it was uncertain whether the southern Korean Peninsula is a natural habitat of Takydromus tachydromoides oldi which will be necessary in further study.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.5 s.236
• /
• pp.770-776
• /
• 2005

The gains fur NC controller parameter are fixed when the controller is combined with a machine. However, the characteristics of controller could be changed as it has being used by the machine or other environmental conditions. Those result in that the tool positioning accuracy is influenced. The loading torque in servo motor influences on the tool positioning accuracy and it is controlled by the parameter gains. It is required to analyze the torque variation with angular positioning accuracy of the servo motor. This study focus on a measuring method and device for verifying angular positioning accuracy of NC servo motor. We used a high resolution An converter for acquiring analogue signal of rotary encoder in servo motor. The positional accuracy for a nominal tool path, which is generated by the combination of axial movements (X,Y,Z), is analyzed with the servo motor torque. The current variation signal is acquired at the power line using a hall sensor and converted to the loading torque of servo motor. The method of measurement and analysis proposed in this study will be used for determining the gains of parameter in NC controller. This gain tuning is also necessary when the controller is set up at a machine.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.12 s.177
• /
• pp.77-86
• /
• 2005

This paper is about the development of Automatic FPC(flexible printed circuit) punching instrument for the improvement of working condition and cost saving. FPC is used to detect the contact position of keyboard and button like a cellular phone. Depending on the quality of the printed ink and position of reference punching point to the FPC, the resistance and current are varied to the malfunctioning values. The size of reference punching point is 2mm and the above. Because the punching operation is done manually, The punching accuracy is varied with operator's condition. Recently, The punching accuracy has deteriorated severely to the 2mm punching reference hall so that assembly of the K/B has hardly done. To improve this manual punching operation to the FPC, automatic FPC punching system is introduced. Precise mechanical parts like a 5-step stepping motor and ball screw mechanism are designed and tested and low cost PC camera is used fur the sake of cost down instead of using high quality vision systems for the factory automation. Test algorithms and programs showed good results to the designed automatic punching system and led to the increasement of productivity and huge cost down to law material like FPC by avoiding bad quality.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.981-984
• /
• 2004

This paper is about the development of Automatic FPC punching instrument. FPC(flexible printed circuit) is used to detect the contact position of K/B and button like a cellular phone. Depending on the quality of the printed ink and position of reference punching point to the FPC, the resistance and current are varied to the malfunctioning values. The size of reference punching point is 2mm and the above. Because the punching operation is done manually, the accuracy of the punching degree is varied with operator's condition. Recently, The punching accuracy has deteriorated severely to the 2mm punching reference hall so that assembly of the K/B has hardly done. To improve this manual punching operation to the FPC, automatic FPC punching system is introduced. Precise mechanical parts like a 5-step stepping motor and ball screw mechanism are designed and tested and low cost PC camera is used for the sake of cost down instead of using high quality vision systems for the FA. Test algorithm shows good results to the designed automatic punching system.