• 전기학회논문지P
• /
• 제56권3호
• /
• pp.148-154
• /
• 2007

In this paper, characteristics of ignition voltage and current by wire length of HID(High Intensity Discharge) lamp circuit are analyzed. In the construction field, decision of the wire thickness for HID lamp circuit has the problems, and these are presented. Through transmit parameters, equivalent model of the ballast and HID lamp circuit was derived. The graph of voltage reduction about length between the ballast and the lamp is shown. The simulation of proposed model and experimental results are presented in order to validate the proposed method. The proposed model and graph can use to choose the proper length of wire between the ballast and the lamp in the field.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제50권10호
• /
• pp.530-535
• /
• 2001

Resonant-type electronic ballast for a metal halide discharge(MHD) lamp is proposed and implemented for 400W MHD lamp. HID lamps have good color rendition, long life and good focusing capability but they have flickers by acoustic resonance when driven at high frequency. A new control method is employed to remove acoustic resonance related instability in HID lamp. By using the amplitude modulation, a spread spectrum effect is employed on the ballast. The control loop of resonant inverter is analyzed and a current is designed. The ballast consists of a power factor controller, an half-bridge resonant inverter, a simple ignitor and an integrator with OP-amps. The experimental results show the good performance as PF 0.93, ballast loss 22W at output 400W and the conducted EMI level is below 60dBuV.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제55권4호
• /
• pp.231-237
• /
• 2006

This paper proposes an effective drive of high intensity discharge (HID) lamp ballast for cars. All control functions of the proposed ballast are implemented using a low-cost single chip microcontroller, PIC16C73 to optimize the total system size and to minimize cost through minimization of total component number. The proposed ballast generates high open-circuit voltage to ignite the lamp and is controlled to supply effectively the power required to shorten warm-up period after the breakdown. The DC-DC converter of the DC-AC converter part of the ballast utilizes the flyback converter topology that can minimize component number. Also, because to more minimize the ballast size, the transformer size must be minimized, for this, PWM (Pulse Width Modulation) pulses are generated with high frequency using the PWM module of the microcontroller. An analysis for this is explained, briefly. As if the operation of the lamp and ballast arrives at steady-state, then the ballast must AC-control the lamp, for this, the microcontroller utilizes the other PWM module. And the part related to the igniter is explained, briefly. It is shown through experimental results that the controller of the proposed ballast has good performance for the HID lamp for cars.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권1호
• /
• pp.27-32
• /
• 2003

The thesis is used by PSpice circuit model to the characteristics of a fluorescent lamp modified form of he classical Cassie and Mayr equations in order to show the characteristics of HID(High-Intensity Discharge) Lamp. This is useful for applying high-frequency electric ballast for HID Lamp, and show that the result of experimentations and simulations, such as lamp rating, input voltage, high-frequency electric ballast which is using the ABM circuit model of the low pressure sodium lamp, come to the voltage and current wave.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제51권10호
• /
• pp.587-594
• /
• 2002

A low frequency square wave electronic ballast for the high intensity discharge(HID) lamps using fuzzy logic controller is developed. This electronic ballast consists a buck converter, a low frequency square wave full bridge inverter, a high voltage pulse generator for the HID lamp ignition, an over current protection circuit and an 8-bit microcontroller. The ballast system is operated on the constant current mode during the HID lamp start-up process and the system is operated on the constant power mode during steady state. Experimental results show that the fuzzy logic control operation is carried out successfully by the 8-bit microcontroller PIC16F877 In this electronic ballast system, in spite of the limited control bandwidth caused by low operating speed of the microcontroller, the good performance in the constant lamp current characteristic is obtained. Acoustic resonance of the HID lamps can be effectively avoided because the instantaneous In lamp power is fully constant due to the low frequency square wave drive.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 하계종합학술대회 논문집(5)
• /
• pp.319-322
• /
• 2002

In this Paper, we suggested the Half-Bridge inverter for the automotive HID electronic ballast. electronic ballast for automotive HID lamp should be supplied by low-frequency square wave avoiding the acoustic resonance(11kHz ∼ 825kHz). When the HID lamp is hot state, the electronic ballast should supply the sufficient current for a few milli-second to the lamp at the re-strike ignition state. that is called take-over current. We have introduced the new take-over current control method that could have reduced the peak current and supplied the sufficient take-over current.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제54권1호
• /
• pp.47-52
• /
• 2005

This paper presents dimming control system for automotive 35W metal halide discharge(MHD) lamp electronic ballast. HID lamp demands a highly efficient ballast and very complex control circuitry that can control complex transient state in applying to automotive. Therefore, in this paper, a microcontroller-based digital control method for the HID lamp ballast is presented for optimal control that can adapt complex transient state, steady state and various environments. In developed dimming system, the system is designed to control the lamp output voltage step by step(continuous) using microcontroller according to CdS sensor. Therefore the designed dimming control system give good driving condition to diver and realize the power control effectively. The results of the proposed system is verified through various experiment results.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권3호
• /
• pp.140-146
• /
• 2003

In this paper, we suggested electronic ballast with the half bridge inverter for the automotive HID lamp. The electronic ballast for the automotive HID lamp should be supplied by the low-frequency square wave avoiding the acoustic resonance. When the HID lamp is hot state, the electronic ballast should supply the sufficient current to the take over to the lamp at the re-strike ignition state for a few milli-second. We have introduced the new take-over current control method that could have control operating frequency and minimize circuits to the take over current circuits.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1999년도 전력전자학술대회 논문집
• /
• pp.595-598
• /
• 1999

A new of the automotive High Intensity Discharge(HID) lamp ballast systems is proposed. Proposed scheme is consisted of the high frequency DC-DC converter and low frequency DC-AC inverter as same as conventional HID ballast system. But this system separates ignition voltage from dc link voltage, which results to used the lower voltage rating power devices for HID lamp ballast system compared with conventional system. As a result, proposed system has a lower cost and higher efficiency.

• 전기학회논문지
• /
• 제58권5호
• /
• pp.944-949
• /
• 2009

A simplified power control technique for electronic ballasts of HID lamps is proposed. This power calculator and controller consist of regular operational amplifiers with some passive elements and form simple add operation circuit. From a mathematical model of designed ballast with proposed power controller, the control performance and stability are analyzed by using Matlab and the results show that the stable starting characteristics and steady state characteristics of HID lamp are appropriately guaranteed. The experimental results of the prototype ballast coincide with the simulation results.