• Clean Technology
• /
• v.23 no.3
• /
• pp.256-269
• /
• 2017

In response to national and international regulations for resource circulation and to reduce greenhouse gas emissions, the automotive industry has tried to reuse scrap parts and defective products produced in the disposal or production stages as recycled resources. Attempts have been made to reach the target recycling rate by reducing the number of material types required for each part. Moreover, in order to achieve greenhouse gas reduction targets while maintaining the performance of existing products, lighter components are being developed. Existing products were 100% incinerated at the disposal stage, but the uni-materialized products were improved to be possible that it could be recycled 90% through scraps and the defective product in the pre-production and production stage. It also appears that the fuel efficiency improves through 56% lightweight compared to the existing product. In this paper, a preliminary assessment is conducted on the applicability of uni-materialized product development of car parts. The environmental impact values of existing products and developed prototypes are compared and analyzed through life cycle assessment.

• Journal of Embryo Transfer
• /
• v.15 no.2
• /
• pp.121-128
• /
• 2000

This study was conducted to enhance the efficiency of embryo transfer and embryos produced in vitro according to select good quality blastocyst among in vivo or in vitro produced embryos. After middle blastocys(MB) and late blastocyst(LB) stages embryos that developed in vitro for 7∼8 days were treated hypertonic solution(380 mOsm or 600 mOsm) and the rate of development to hatched blastocyst(HB) was examined. The results obtained were summarized as follows: The proportion of embryos developed to HB was higher than that of control regardless of hypertonic solution treatment. However, it was related to culture time in hypertonic solution The propotrion of embryos developed to HB of morphologically recovered embryos in 380 nOsm solution ws higher than that of morphologically shrinked embryos. However, treatment time was not significantly different the rates of HB development. Especially, the proportion of embryos developed to HB of morphologically recovered embryos of the 30-min-treated group was significantly higher than that of control (p<0.05). The results suggest that hypertonic solution treatment should enhance the efficiency for criterion of transferable blastocyst quality.

• Korean Journal of Childcare and Education
• /
• v.10 no.1
• /
• pp.27-42
• /
• 2014

The primary purpose of this study was to examine the influence of mothers' emotion expressiveness and children's attributional biases on children's aggressive behavior, focusing on gender differences. The data were collected from a total of 86 children; 46 6-year-old boys and 40 6-year-old girls in kindergartens, and their mothers in Seoul. The emotion expressiveness of the mothers were measured by a self-reported Korean version of SEFQ(Self Expressivness Family Questionnaire). Attributional biases of the children were evaluated by using Dodge and Frame's Story-Based Interview Scale. Children's aggressive behavior were measured by teachers using a children's Aggressive Behavior Scale developed by Crick(1995). T-test, correlation analysis, and multiple regression were used to analyze the collected data. The results showed that the relational attributional biases of children positively influenced overt/relational aggressive behaviors. The emotion expressiveness of mothers and the aggressive behavior of children, however, were not significant. Regarding gender differences in children, the negative emotion expressiveness of mothers predicted the girl's relational aggressive behavior negatively. Implications and limitations of this study were discussed.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.2
• /
• pp.267-275
• /
• 2015

In this paper, ZnO films were prepared by atomic layer deposition (ALD) and CdS films were deposited using chemical bath deposition (CBD) to form ZnO/CdS heterojunction. More accurate mapping of band arrangement of the ZnO/CdS heterojunction has been performed by analyzing its electrical and optical characteristics in depth by various methods including transmittance, x-ray photoemission spectroscopy (XPS), and ultraviolet photoemission spectroscopy (UPS). The optical bandgap energies ($E_g$) of ZnO and CdS were 3.27 eV and 2.34 eV, respectively. UPS was capable of extracting the ionization potential energies (IPEs) of the materials, which turned out to be 8.69 eV and 7.30 eV, respectively. The electron affinity (EA) values of ZnO and CdS calculated from IPE and $E_g$ were 5.42 eV and 4.96 eV, respectively. Energy-band structures of the heterojunction could be accurately drawn from these parameters taking the conduction band offset (CBO) into account, which will substantially help acquisition of the full band structures of the thin films in the CIGS solar-cell device and contribute to the optimal device designs.

• Journal of Hydrogen and New Energy
• /
• v.27 no.4
• /
• pp.412-420
• /
• 2016

Effect of $H_2S$ on reactivity of oxygen carrier was measured and discussed using fluidized bed reactor and SDN70 oxygen carrier. We could get 100% of fuel conversion and $CO_2$ selectivity even though $H_2S$ containing simulated syngas was used as fuel for reduction. Absorbed sulfur was released during oxidation and $N_2$ purge step after oxidation as $SO_2$ form. We could get 100% of fuel conversion and $CO_2$ selectivity during cyclic reduction-oxidation tests up to 10th cycle. However, only 6~7% of sulfur can be removed during oxidation and $N_2$ purge step and 93~94% of sulfur was accumulated in the oxygen carrier. Therefore we could conclude that total removal of sulfur was not possible. $SO_2$ emission during oxidation decreased as the number of cycle increased. Therefore we could expect that the reactivity of oxygen carrier will be decreased with time.

• Journal of Hydrogen and New Energy
• /
• v.24 no.6
• /
• pp.535-542
• /
• 2013

To enhance the performance of SEWGS system by holding the WGS catalyst in a SEWGS reactor using bed inserts, effect of bed insert geometry on CO conversion of WGS catalyst was measured and investigated. Small scale fluidized bed reactor was used as experimental apparatus and tablet shaped WGS catalyst and sand particle were used as bed materials. The cylinder type and the spring type bed inserts were used to hold the WGS catalysts. The CO conversion of WGS catalyst with the change of steam/CO ratio was determined based on the exit gas analysis. Moreover, gas flow direction was confirmed by bed pressure drop measurement for each case. The measured CO conversion using the bed inserts showed high value comparable to previous results even though at low catalyst content. Most of input gas flowed through the bed center side when we charged tablet type catalyst into the cylinder type bed insert and this can cause low $CO_2$ capture efficiency because the possibility of contact between input gas and $CO_2$ absorbent is low in this case. However, the spring type bed insert showed good reactivity and good distribution of gas, and therefore, the spring type bed insert was selected as the best bed insert for SEWGS process.

• Membrane and Water Treatment
• /
• v.11 no.1
• /
• pp.41-48
• /
• 2020

Lead is a highly toxic heavy metal that causes serious health problems. Nonetheless, it is increasingly being used for industrial applications and is often discharged into the environment without adequate purification. In this study, Pb(II) was removed by powdered waste sludge (PWS) based on the biosorption mechanism. Different PWSs were collected from a submerged moving media intermittent aeration reactor (SMMIAR) and modified Ludzack-Ettinger (MLE) processes. The contents of extracellular polymeric substances were similar, but the surface area of MLE-PWS (2.07 ㎡/g) was higher than that of SMMIAR-PWS (0.82 ㎡/g); this is expected to be the main parameter determining Pb(II) biosorption capacity. The Bacillaceae family was dominant in both PWSs and may serve as the major responsible bacterial group for Pb(II) biosorption. Pb(II) biosorption using PWS was evaluated for reaction time, salinity effect, and isotherm equilibrium. For all experiments, MLE-PWS showed higher removal efficiency. At a fixed initial Pb(II) concentration of 20 mg/L and a reaction time of 180 minutes, the biosorption capacities (q_e) for SMMIAR- and MLE-PWSs were 2.86 and 3.07 mg/g, respectively. Pb(II) biosorption using PWS was rapid; over 80% of the maximum biosorption capacity was achieved within 10 minutes. Interestingly, MLE-PWS showed enhanced Pb(II) biosorption with salinity values of up to 30 g NaCl/L. Linear regression of the Freundlich isotherm revealed high regression coefficients (R² > 0.968). The fundamental Pb(II) biosorption capacity, represented by the K_F value, was consistently higher for MLE-PWS than SMMIAR-PWS.

• Asian Pacific Journal of Cancer Prevention
• /
• v.15 no.7
• /
• pp.3179-3183
• /
• 2014

Background: The purpose of study was to evaluate radiologic or clinical features of breast cancer undergoing ultrasound (US)-guided 14G core needle biopsy (CNB) and analyze the differences between underestimated and accurately diagnosed groups. Materials and Methods: Of 1,898 cases of US-guided 14G CNB in our institute, 233 cases were proven to be cancer by surgical pathology. The pathologic results from CNB were invasive ductal carcinoma (IDC) (n=157), ductal carcinoma in situ (DCIS) (n=40), high-risk lesions in 22 cases, and benign in 14 cases. Among high-risk lesions, 7 cases of atypical ductal hyperplasia (ADH) were reported as cancer and 11 cases of DCIS were proven IDC in surgical pathology. Some 29 DCIS cases and 157 cases of IDC were correctly diagnosed with CNB. The clinical and imaging features between underestimated and accurately diagnosed breast cancers were compared. Results: Of 233 cancer cases, underestimation occurred in 18 lesions (7.7%). Among underestimated cancers, CNB proven ADH (n=2) and DCIS (n=11) were diagnosed as IDC and CNB proven ADH (n=5) were diagnosed at DCIS finally. Among the 186 accurately diagnosed group, the CNB results were IDC (n=157) and DCIS (n=29). Comparison of underestimated and accurately diagnosed groups for BI-RADS category, margin of mass on mammography and US and orientation of lesion on US revealed statistically significant differences. Conclusions: Underestimation of US-guided 14G CNB occurred in 7.7% of breast cancers. Between underestimated and correctly diagnosed groups, BI-RADS category, margin of the mass on mammography and margin and orientation of the lesions on US were different.

• Composites Research
• /
• v.28 no.5
• /
• pp.260-264
• /
• 2015

In this paper, molecular dynamics (MD) simulation was carried to predict thermo-mechanical behaviors for carbon nanotube (CNT) reinforced epoxy composites and to analyze the trends. Total of six models having the volume fractions of CNT from 0 to 25% in epoxy were constructed. To predict thermal behaviors, temperature was increased constantly from 300 to 600 K, and the glass transition temperature ($T_g$) and coefficient of thermal expansion (CTE) analyzed using the relationship between temperature and specific volume. The elastic moduli that represented to the mechanical behaviors were also predicted by constant strain. Additionally, the effects of functionalization of CNT on mechanical behaviors of composite were analyzed. Models were constructed to represent CNTs functionalized by nitrogen doping and COOH groops, and interfacial behaviors and elastic moduli were analyzed. Results showed that the agglomerations of CNTs in epoxy cause by perturbations of thermo-mechanical behaviors, and the functionalization of CNTs improved the interfacial response as well as mechanical properties.

• Asian Pacific Journal of Cancer Prevention
• /
• v.17 no.7
• /
• pp.3071-3075
• /
• 2016

Morin, a flavonoid found in figs and other Moraceae species, displays a variety of biological actions, exerting anti-oxidant, anti-inflammatory and anti-carcinogenic effects. Here, we investigated the anti-cancer activity of morin focusing on anti-adhesive influence. We performed experiments with MDA-MB-231 human breast cancer cells. Morin inhibited TNF-induced cancer cell adhesion to human umbilical vein endothelial cells (HUVECs) without showing any toxicity. It further inhibited the expression of VCAM-1 on MDA-MB-231 cells as well as HUVECs. Morin also decreased the expression of N-cadherin on MDA-MB-231 cells. In addition, there was apparent anti-metastatic activity in vivo. In conclusion, this study suggested that morin inhibits cancer cell adhesion to HUVECs by reducing VCAM-1, and EMT by targeting N-cadherin, and that it features anti-metastatic activity in vivo. Further investigation of possible anti-metastatic activity of morin against human breast cancer cells is warranted.