• Proceedings of the KIEE Conference
• /
• 1997.07f
• /
• pp.2075-2077
• /
• 1997

An electronic starter using MOSFET is developed to take advantage of ideal preheating and starting features which can extend the lifetime of fluorescent lamps. The preheating curcuit of the developed electronic starter is consisted of three parts - a full wave rectifier curcuit, an FET switching curcuit, and a timer curcuit for the gate switching. The curcuit allows sufficient preheating current flow before the starting to protect lamp filaments, nevertheless it shortens the Preheating time and enables a single pulse ignition at the peak level of the line voltage. Experimental results show that fluorescent lamps of 20-40W range can be initiated within rather short time of $1{\sim}1.5sec$ with preheating current of 0.6A. The electronic starter withstands more than 70.000 cycles switchings without noticeable blackening due to anode spot. These features provide Proper evidences for the advantage of direct replacement with the new starter.

• Proceedings of the KIPE Conference
• /
• 2003.07a
• /
• pp.430-433
• /
• 2003

IGBTS are widely used for the industrial inverters in the mid power range at low voltage (440V$\~$660V) application. Advantageous features of the device are simple gate drive and high speed switching capability. Due to these advantages the application of IGBTS is enlarging into the high power application. However, to increase the power handling capacity at lower input voltage level, the current rating in each bridge arm must be enlarged. Therefore the parallel operation of IGBT devices is essentially needed. This paper describes the feasible parallel structures of the power circuit for the mid & the high power inverters and introduces the important design condition for the parallel operation of IGBT devices. To verify feasibility of the IGBT parallel operation, the feature of several IGBT devices (EUPEC, SEMIKRON's IGBT) are investigated and the power stacks are implemented and tested with these devices. The experimental results show the good characteristics for the parallel operation of IGBTS.

• Journal of Oriental Neuropsychiatry
• /
• v.18 no.3
• /
• pp.261-275
• /
• 2007

Parkinson's Disease is a well known degenerative disease which result's in the depletion of dopamin-producing neurons in the pars compacta of the substantia nigra. This is a chronic, progressive disorder characterized by progressive muscular rigidity, pill-rolling tremor, flexed posture, shuffling gate and akinesia. This study was designed to evaluate the effects of an oxygen therapy with various scales on symptoms of Parkinson's disease. We treated his disease with Oxygen treatment , including herbal medicine acupuncture, and trigger point therapy, and we evaluated the clinical progress of the patient using UPDRS and H- Y stage. After treatment for about 1-month, the chief complaints and tremor symptoms were improved. This study suggests that oxygen therapy is significantly effective in the treatment of Parkinson's disease.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.573-575
• /
• 1994

Resent research activities and technical trends for UPS(UNINTERRUPTIBLE POWER SUPPLY) are reviewed. There are increasing demands for UPS to get mote useful performance. This needs are high-efficiency, high-confidency, high-quality, low-cost. self-diagnosis. maintenance-free, and a wide variety of options. These can be satisfied with high-technology and optimal system coordination. In this paper. according to these demands. a newly developed UPS and a wide variety of options are introduced. Also. the data related are presented.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.429-431
• /
• 2003

CCTV network has been implemented to transmit the image information of platform, ticket gate and transfer section to local headquarters in the KNR(Korean National Railroad). But, communication system for transferring image information around accident field or wayside has not been established ret. thus, at Present implementation of communication equipment is necessary for dynamic image of unspecified accident to be transmitted to headquarters. Copper cable communication network is run by KNR, but it is processing installation of optical cable in connection with the implemental plan for high-speed network from now on. And, the capacity of communication channel will be guaranteed much more than now between station and station. station and central headquarters when optical cable is completed. This study analyzes the image equipment of field for transmission and estimated matters to transmit image information of accident field to headquarters with using communication infrastructure. And, the study considers implemental method of communication network for long-distance image transmission from dozens to hundreds kilometers.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.497-497
• /
• 2013

Semiconducting amorphous InGaZnO (a-IGZO) has attracted significant research attention as improved deposition techniques have made it possible to make high-quality a-IGZO thin films. IGZO thin films have several advantages over thin film transistors (TFTs) based on other semiconducting channel layers.The electron mobility in IGZO devices is relatively high, exceeding amorphous Si (a-Si) by a factor of 10 and most organic devices by a factor of $10^2$. Moreover, in contrast to other amorphous semiconductors, highly conducting degenerate states can be obtained with IGZO through doping, yet such a state cannot be produced with a-Si. IGZO thin films are capable of mobilities greaterthan 10 $cm^2$/Vs (higher than a-Si:H), and are transparent at visible wavelengths. For oxide semiconductors, carrier concentrations can be controlled through oxygen vacancy concentration. Hence, adjusting the oxygen partial pressure during deposition and post-deposition processing provides an effective method of controlling oxygen concentration. In this study, we deposited IGZO thinfilms at optimized conditions and then analyzed the film's electrical properties, surface morphology, and crystal structure. Then, we explored how to generate IGZO thin films using DC magnetron sputtering. We also describe the construction and characteristics of a bottom-gate-type TFT, including the output and transfer curves and bias stress instability mechanism.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.1
• /
• pp.71-77
• /
• 2008

This paper proposes an Electronic Throttle Body (ETB) model considering a non-linearity of DC motor driver which is integrated with a H-bridge and a gate driver. A propagation delay and reverse recovery time of switching components cause non-linear characteristic of DC motor driver. This non-linearity affects not only the amateur voltage of DC motor, but also entire behaviour and parameters of ETB. In order to analyze the behavior of ETB more accurately, this non-linear effect of DC motor driver is modeled. The developed ETB model is validated by use of the step response and ramp response experiments, and it shows relatively accurate results compared with linear DC motor driver model.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.3
• /
• pp.467-477
• /
• 2009

Renewable Portfolio Standard (RPS) is a regulatory policy that requires the generation companies to increase the proportion of renewable energy sources such as wind, solar, LFG, fuel cell, and small hydro. Recently, Korean government decided to increase the portion of renewable energy to 3% to total electricity generation by 2012 from the current level of 0.13%. To achieve this goal, an innovative plan for market competitiveness would be required in addition to the present Feed-In-Tariff (FIT). That is Korean government has taken it into consideration to introduce a Renewable Portfolio Standard (RPS) as an alternative to FIT. This paper reviews the impact of RPS on the long-term fuel mix in 2020. The studies have been carried out with the GATE-PRO (Generation And Transmission Expansion PROgram) program, a mixed-integer non-linear program developed by Hongik university and Korea Energy Economics Institute. Detailed studies on long-term fuel mix in Korea have been carried out with four RPS scenarios of 3%, 5%, 10% and 20%. The important findings and comments on the results are given to provide an insight on future regulatory policies.

• Journal of the Korean Institute of Educational Facilities
• /
• v.11 no.4
• /
• pp.15-24
• /
• 2004

The purpose of this study is to suggest some alternative on site planning of elementary school through investigating the effects of geographical and urban environment on the site. For this, we selected and surveyed 35 schools in Gwangju. The results of this study are as follows. 1) We cannot find out the differences from the use of elementary schools sites on slopes of sites. However, the sunken space between H type buildings in the site slopes facing east or west and the placing the playground on the north side of the site slopes facing north have some problems 2) The number of adjacent road and surrounding environment didn't show any effect. To separate between cars and pedestrians, we need some plans to block cars on the pedestrian gateway and it is much better to intensify the parking area near the school gate that cars come in and out. 3) The degree of satisfaction on the outdoor facilities of these cases shows low level. Therefore, to use the site of schools efficiently, we should secure the spacious playground and make plans to provide some spaces around school building for the static activities of students and teachers. 4) Most of all, the site which is suitable for educational environment should be selected. and also Special Code on the urban plan should be established to develop this one.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1214-1218
• /
• 2006

We introduced simple fabrication process for field emission devices based on carbon nanotubes (CNTs) emitters. Instead of using the ITO material as a transparent electrode, a metal (Au) with thickness of 5-20nm was used. Moreover, the ITO patterning process was eliminated by depositing metal layer, before the CNT printing process. In addition, the thin metal layer on photo resist (PR) layer was used as UV block. We fabricated the CNT field emission arrays of triode structure with simple process. And I-V characteristics of field emission arrays were measured. The maximum current density of $254{\mu}A/cm2$ was achieved when the gate and the anode voltage was kept 150V and 3000V, respectively. The distance between anode and cathode was kept constant.