• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.45 no.1
• /
• pp.14-21
• /
• 2009

This experimental study was carried out to obtain the base data for saving the man power in the fishing operation of largehead hairtail hand line by using the continuous type hand line system with a rotary device which could make a main line move automatically. In order to solve the twists and entangling on the main line happened during operating test, the resistance board was suspended at the end of the main line at sea. As the result, there were no problems of tangling and so on due to up and down moving of a main line. According to the control of a fixed angle of guide roller, it was possible to prevent the main line to be separated from a side roller and a guide roller. In addition, PVC tube between a guide roller and a side roller enabled a main line to be moved smoothly without any entanglement.

• Journal of Biosystems Engineering
• /
• v.42 no.2
• /
• pp.112-116
• /
• 2017

Purpose: The purpose of this study was to analyze the milling characteristics of white rice depending on the guide angles of the cutting roller's induced guide, as well as to verify optimum milling conditions for the cutting-type milling machine. Methods: Brown rice, which was produced in Cheongju-si, Chungcheongbuk-do, Republic of Korea, in 2014, was used as the experimental material. The milling characteristics of white rice were measured under six different guide angle levels of the cutting roller, which were none, $0^{\circ}$, $5^{\circ}$, $10^{\circ}$, $15^{\circ}$, and $20^{\circ}$. The quantity of brown rice for each experiment was 500 kg, and the milling characteristics were measured according to the whiteness, rice temperature, cracked rice ratio, broken rice ratio, and energy consumption. Results: The whiteness of white rice maintained a uniform level, indicating at range of $38{\pm}0.5$, regardless of the cutting roller guide angles under all conditions. The rice temperature rise during milling was found to be rather low, at $13.9^{\circ}C$ and $13.6^{\circ}C$ at $10^{\circ}$ and $15^{\circ}$ guide angles, respectively. The cracked rice ratio after milling was 18.67%-19.47%, and the broken rice ratio was 0.68% at a $10^{\circ}$ guide angle, which is the lowest in comparison to other guide angles. Energy consumption was lower when the guide was used compared to that with-out the use of the guide. The energy consumption tended to increase as the cutting roller guide angle increased. Conclusions: From the above results, we conclude that the cutting roller guide angles of $0^{\circ}$ and $10^{\circ}$ are suitable for producing high quality rice during milling with a cutting-type milling machine.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.23 no.9
• /
• pp.620-626
• /
• 2011

The purpose of this study is to evaluate a simulation model of a stacking guidance system (SGS) with a roller guide applicable to the mobile harbor. The study used a small-scale model (1/20) made of wood with rollers in order to compare the dynamic analysis with experiment results. The law of similarity was applied for the validation of the scaled model. In order to construct a more realistic simulation model, the damping coefficient of the dynamic model was adjusted to 0.5 Ns/mm for the wood-to-wood contact condition based on the experimental results. Using this validated model, dynamic simulations were also carried out for containers of 20, 30, and 40 tons. The results showed that the reaction force of the roller guide was increased from 74.7 kN to 91.2 kN as the weight of container increased. For the design of a roller guide for SGS, the results obtained in this study can be used to reduce the reaction force by employing a rubber roller or a highly damped rotational joint.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.4
• /
• pp.325-332
• /
• 2011

This paper is concerned with the active control experiments on elevator vibrations by means of the active roller guide. To this end, a roller guide was designed using a voice-coil actuator and linear guide. A simple proportional control algorithm combined with the band-pass filter was implemented using the DSP. Based on the initial experiments, a new control system which can handle lateral and front-back vibrations of elevator was built and tested using the elevator test tower. The experimental results show that the elevator vibrations are reduced by the active control technique.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.527-528
• /
• 2010

• Proceedings of the KIEE Conference
• /
• 1999.07b
• /
• pp.671-673
• /
• 1999

In order to cope with the occurrence of abnormal operation, rotatory condition monitoring system for guide roller of finishing train in wire rolling has been developed. In this study, proximity sensor and its holding devices that could overcome severe in-situ measurement conditions was designed and MMI software using C++ was programmed. Performance of the developed system turned out to be good enough as results of in-line test for POSCO #3 wire rolling mill. It is expected to contribute to prevent the cobble and the grade-down of products caused by the abnornormal operation of guide rollers.

• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.454-458
• /
• 2001

In this paper, contact between the coupler-roller and guide in elevator door mechanism is modeled and analyzed with DADS 3D program. The contact force of coupler-roller is an important factor for impact and noise reduction when doors of elevator are opened or closed. To minimize the maximum contact force, an optimal cam profile for the door guide is suggested. To find an optimal shape of the guide, several types of motion curve are tested with DADS contact module.

• Journal of the Semiconductor & Display Technology
• /
• v.9 no.1
• /
• pp.23-28
• /
• 2010

In this paper, wafer drop from wafer guide mechanism, which is one of the serious problems in water transfer robot, is analyzed, and new wafer guide mechanisms are proposed to minimize this drop. Three types of new wafer guide mechanisms are proposed: roller type, gear type and L-shape rocker type. We choose one of the proposed mechanism, which is roller type, and verified this mechanism through real transfer experiment. Wafer picking up test is conducted with initial aligning error for simulating the wafer drop. Number of drop is compared between conventional mechanism and proposed mechanism. As a result, we can find the proposed mechanism can reduce the number of wafer drop dramatically.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.6
• /
• pp.474-480
• /
• 2008

Recently, rods having irregular sections more complex than a rectangle or ellipse are necessary to produce mechanical parts. The cold shaped drawing process is used to obtain shaped drawn products with high levels of dimensional accuracy and quality. A cross roller guide, considered in this study, is one of the parts produced by shaped drawing process. A cross roller guide has a linear bearing system that rolls along a guide way. A cross roller guide is one of the most important components in terms of equipment because the quality of the product influences the precision linear motion. Therefore, the final dimensional accuracy of the linear rail in the shaped drawing is very important. The objective of this study is to find the optimized die angles to improve the dimensional accuracy and straightness of the final shaped drawn product. In order to achieve the aim of this study, design of experiment, FE-simulation, and the Taguchi method were used. Based on the analytical results, shaped drawing experiment has been performed to verify the result.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.71-76
• /
• 2008

This paper is concerned with the active vibration control of elevator by means of the active roller guide. To this end, a dynamic model for the horizontal vibration of the elevator consisting of a supporting frame, cage and active roller guides was derived using the energy method. Free vibration analysis was then carried out based on the equations of motion. Active vibration controller was designed based on the equations of motion using the LQR theory and applied to the numerical model. Rail irregularity and wind pressure variation were considered as external disturbance in the numerical simulations. The numerical results show that the active vibration control of elevator is possible.