• Journal of Powder Materials
• /
• v.25 no.2
• /
• pp.104-108
• /
• 2018

Grain-growth behavior in the $95Na_{1/2}Bi_{1/2}TiO_3-5BaTiO_3$ (mole fraction, NBT-5BT) system has been investigated with the addition of $Na_2CO_3$. When $Na_2CO_3$ is added to NBT-5BT, the growth rate is higher than desired and grains are already impinging each other during the initial stage of sintering. The grain size decreases as the sintering temperature increases. With the addition of $Na_2CO_3$, a liquid phase infiltrates the interfaces between grains during sintering. The interface structure can be changed to be more faceted and the interface migration rate can increase due to fast material transport through the liquid phase. As the sintering temperature increases, the impingement of abnormal grains increases because the number of abnormal grains increases. Therefore, the average grain size of abnormal grains can be decreased as the temperature increases. The phenomenon can provide evidence that grain coarsening in NBT-5BT with addition of $Na_2CO_3$ is governed by the growth of facet planes, which would occur via mixed control.

• Journal of Ocean Engineering and Technology
• /
• v.3 no.2
• /
• pp.125-137
• /
• 1989

To check technical improvement in the soundness and strength of 12% Cr steel rotor, a 25 tons of rotor with 65 tons of ingot was made in real size and was cut to pieces to take test samples, and the various mechanical tests such as impact, tensile, creep, and fatigue were carried out. The strengths are compared with those of 1% Cr-Mo-V rotor of same size. Microstructures of the samples are examined and reviewed. The results can be summarized as follows. 1) Fracture appearance transition temperatures are 80.deg. C at the center part and 60.deg. C near surface of 12% Cr rotor, and 8.deg. C near surface of 1% Cr-Mo-V rotor. 2) Comparative rapid softening occurs at higher temperatures above 600.deg. C for 12% Cr steel and 550.deg. C for 1% Cr-Mo-V steel in tension tests. 3) Fatigue crack propagation rate of 12% Cr steel is almost same as that of 1% Cr-Mo-V steel at the same corresponding surface part of the rotors. The crack growth rate of center part of 12% Cr rotor is faster than near surface part of the rotor, and the crack growth rate at the load condition of R=0.04 is slower than that of the load condition of R=0.5 for both 12% Cr steel and 1% Cr-Mo-V steel. 4) Crack growth rate of radial direction near surface of 12% Cr rotor is faster than that of transverse direction at the same part because of the difference in residual stresses. 5) Both creep and fatigue strengths of 12% Cr steel are superior to those of 1% Cr-Mo-V steel and the difference is thought the effect of climb and glide controlled creep by solid solution of alloying elements and dispersion of carbides.

• Journal of Ocean Engineering and Technology
• /
• v.3 no.2
• /
• pp.625-625
• /
• 1989

To check technical improvement in the soundness and strength of 12% Cr steel rotor, a 25 tons of rotor with 65 tons of ingot was made in real size and was cut to pieces to take test samples, and the various mechanical tests such as impact, tensile, creep, and fatigue were carried out. The strengths are compared with those of 1% Cr-Mo-V rotor of same size. Microstructures of the samples are examined and reviewed. The results can be summarized as follows. 1) Fracture appearance transition temperatures are 80.deg. C at the center part and 60.deg. C near surface of 12% Cr rotor, and 8.deg. C near surface of 1% Cr-Mo-V rotor. 2) Comparative rapid softening occurs at higher temperatures above 600.deg. C for 12% Cr steel and 550.deg. C for 1% Cr-Mo-V steel in tension tests. 3) Fatigue crack propagation rate of 12% Cr steel is almost same as that of 1% Cr-Mo-V steel at the same corresponding surface part of the rotors. The crack growth rate of center part of 12% Cr rotor is faster than near surface part of the rotor, and the crack growth rate at the load condition of R=0.04 is slower than that of the load condition of R=0.5 for both 12% Cr steel and 1% Cr-Mo-V steel. 4) Crack growth rate of radial direction near surface of 12% Cr rotor is faster than that of transverse direction at the same part because of the difference in residual stresses. 5) Both creep and fatigue strengths of 12% Cr steel are superior to those of 1% Cr-Mo-V steel and the difference is thought the effect of climb and glide controlled creep by solid solution of alloying elements and dispersion of carbides.

• Journal of the Korean Ceramic Society
• /
• v.35 no.12
• /
• pp.1336-1336
• /
• 1998

A twt -step carbothermal reduction scheme has been employed for the synthesis of SiC whiskers in an Ar or a H2 atmosphere via vapor-solid two-stage and vapor-liquid-solid growth mechanism respectively. It has been shown that the whisker growth proceed through the following reaction mechanism in an Ar at-mosphere : SiO2(S)+C(s)-SiO(v)+CO(v) SiO(v)3CO(v)=SiC(s)whisker+2CO2(v) 2C(s)+2CO2(v)=4CO(v) the third reaction appears to be the rate-controlling reaction since the overall reaction rates are dominated by the carbon which is participated in this reaction. The whisker growth proceeded through the following reaction mechaism in a H2 atmosphere : SiO2(s)+C(s)=SiO(v)+CO(v) 2C(s)+4H2(v)=2CH4(v) SiO(v)+2CH4(v)=SiC(s)whisker+CO(v)+4H2(v) The first reaction appears to be the rate-controlling reaction since the overall reaction rates are enhanced byincreasing the SiO vapor generation rate.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.4
• /
• pp.581-589
• /
• 2020

In this paper, a solid capsule was prepared using a crystal growth type inorganic material capable of hydration reaction, the quality and mechanical healing properties of self-healing mortar with solid capsules were evaluated. Solid capsules were mixed 5% by mass of cement. Reloading test results of compressive load, it was found to improve about 20% on average for the natural healing effect of Plain, in the case of the elastic range, the healing rate was about 79% at the 7 days of healing age and 98% at the 28 days of healing age. Reload test results of flexural load, in the case of the elastic range, the healing rate was about 79% at the 7 days of healing age and 98% at the 28 days of healing age. Through these results, it is judged that the healing performance of solid capsules has also an effect on mechanical healing properties such as strength in addition to the durability properties obtained by the permeability test. Since the strength tends to decrease as the solid capsules are mixed, it is considered necessary to compensate.

• Journal of Fisheries and Marine Sciences Education
• /
• v.25 no.6
• /
• pp.1285-1293
• /
• 2013

This study was conducted to investigate the effects of dietary inclusion of various additives Solid sulfur, fucoidan, and glucan on growth performance and immune responses in Juvenile olive flounder paralichthys olivaceus. Six experimental diets supplemented with : no additives (CON); 0.5 and 1.0% solid sulfur (S); 0.2 and 0.4% fucoidan (F); 0.1% glucan (G) of these additives diet on a dry-matter basis. Fish averaging $8.2{\pm}0.17g$ were fed one of six experimental diets in triplicate groups for 6 weeks. By the end of the feeding trial, weight gain, feed efficiency, specific growth rate, protein efficiency ratio, hepatosomatic index and condition factor of fish fed diet CON were significantly lower then those of fish fed the all additives diets (P < 0.05). In challenge test, fish were infected by intraperitonel injection of 0.1 ml bacterial suspension with Edwardsiella tarda per fish after the feeding trial. As a result fish fed All additive diet showed a lower cumulative mortality then did fish fed CON diet throughout the challenge test. In conclusion, these results indicated that solid sulfur, fucoidan and glucan enhanced the growth, feed efficiency and non-specific immune activity of juvenile flounder and protect the fish against microbial infections.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.1
• /
• pp.59-66
• /
• 2020

In this study, self - healing solid capsules of crystal growth type which can be mixed directly with repair mortar were prepared, and the quality and crack healing performance of repair mortar with self - healing solid capsules were evaluated. The table flow and the air flow rate of the repair mortar material mixed with self-healing solid capsules were found to have no significant influence on table flow and air volume regardless of mixing ratio. Compressive strength tended to decrease with increasing capsule mixing ratio. As a result of evaluation of crack healing properties according to constant water head permeability test, initial water permeability decreased, and reaction products were generated over time and cracks were healed.

• KSBB Journal
• /
• v.8 no.4
• /
• pp.382-389
• /
• 1993

In order to elucidate the effect of acetate ion on the growth of Escherichia coli, flask and fermentor cultures were performed using M9 and LB media. Acetic acid was secreted at a higher rate under the conditions of high glucose concentration as well as of richer medium, i. e., LB broth. The pH in flask culture could not be controlled as i fermentor and pH decreased with the formation of acetic acid. The inhibition effect of acetic acid was pronounced at a lower pH, and the effective inhibitory concentrations of acetic acid were 2.0g/l for LB flask culture, 4.0g/l for M9 flask culture, and 8.0g/l for M9 fermentor culture. Dialysis flask culture was designed to slowly provide E coli cells with glucose. Solid LB agar was layered under LB liquid medium with the variation of agar concentration and solid volume, The increase in the solid portion in the total volume(agar＋liquid) resulted in the increase of the final cell concentration. This can be ascribed to the fact that the larger solid phase behaves like a larger reservoir for glucose and controls the growth of E. coli with a controlled rate.

• 한국전산유체공학회:학술대회논문집
• /
• 2009.04a
• /
• pp.355-362
• /
• 2009

Most material of engineering interest undergoes solidification process from liquid to solid state. Identifying the underlying mechanism during solidification process is essential to determine the microstructure of material which governs the physical properties of final product. In this paper, we expand our previous two-dimensional numerical technique to three-dimensional simulation for computing dendritic solidification process with fluid convection. We used Level Contour Reconstruction Method to track the moving liquid-solid interface and Sharp Interface Technique to correctly implement phase changing boundary condition. Three-dimensional results showed clear difference compared to two-dimensional simulation on tip growth rate and velocity.

• Journal of Microbiology and Biotechnology
• /
• v.25 no.6
• /
• pp.803-813
• /
• 2015

The growth of Irpex lacteus F17 and manganese peroxidase (MnP) production in a selfdesigned tray bioreactor, operating in solid-state conditions at a laboratory scale, were studied. The bioreactor was divided into three layers by three perforated trays. Agroindustrial residues were used both as the carrier of bound mycelia and as a nutrient medium for the growth of I. lacteus F17. The maximum biomass production in the bioreactor was detected at 60 h of fermentation, which was consistent with the CO₂ releasing rate by the fungus. During the stationary phase of fungal growth, the maximum MnP activity was observed, reaching 950 U/l at 84 h. Scanning electron microscopy images clearly showed the growth situation of mycelia on the support matrix. Furthermore, the MnP produced by I. lacteus F17 in the bioreactor was isolated and purified, and the internal peptide sequences were also identified with mass spectrometry. The optimal activity of the enzyme was detected at pH 7 and 25℃, with a long half-life time of 9 days. In addition, the MnP exhibited significant stability within a broad pH range of 4-7 and at temperature up to 55℃. Besides this, the MnP showed the ability to decolorize the polymeric model dye Poly R-478 in vitro.