• 한국세라믹학회지
• /
• 제51권1호
• /
• pp.19-24
• /
• 2014

Three-layer porous alumina-mullite composites with a symmetric gradient porosity are prepared using a controlled freeze/gel-casting method. In this work, tertiary-butyl alcohol (TBA) and coal fly ash with an appropriate addition of $Al_2O_3$ were used as the freezing vehicle and the starting material, respectively. When sintered at $1300-1500^{\circ}C$, unidirectional macro-pore channels aligned regularly along the growth direction of solid TBA were developed. Simultaneously, the pore channels were surrounded by less porous structured walls. A high degree of solid loading resulted in low porosity and a small pore size, leading to higher compressive strength. The sintered porous layered composite exhibited improved compressive strength with a slight decrease in its porosity. After sintering at $1500^{\circ}C$, the layered composite consisting of outer layers with a 50 wt% solid loading showed the highest compressive strength ($90.8{\pm}3.7MPa$) with porosity of approximately 26.4%.

• 열처리공학회지
• /
• 제25권3호
• /
• pp.126-133
• /
• 2012

Semi-solid forming of the high melting point alloys such as steel is a promising near-net shape forming process for decreasing manufacturing costs and increasing the quality of the final products. This paper presents the microstructure characteristics of SKH51 (high speed tool steel) during heating and holding in the mushy zone between $1233^{\circ}C$ and $1453^{\circ}C$, which has been measured by differential scanning calorimetry (DSC). The results of heating/holding experiments showed that the grain size and the liquid fraction increased gradually with temperature up to $1350^{\circ}C$. The drastic grain growth occurred at heating above $1380^{\circ}C$. The strain-induced melt-activated (SIMA) process has been applied to obtain globular grains in the billet materials. Working by mechanical upsetting and successive heating of SKH51 into the temperatures in the mushy zone resulted in globular grains due to recrystallization and partial melting.

• 한국해양공학회지
• /
• 제3권2호
• /
• pp.125-137
• /
• 1989

To check technical improvement in the soundness and strength of 12% Cr steel rotor, a 25 tons of rotor with 65 tons of ingot was made in real size and was cut to pieces to take test samples, and the various mechanical tests such as impact, tensile, creep, and fatigue were carried out. The strengths are compared with those of 1% Cr-Mo-V rotor of same size. Microstructures of the samples are examined and reviewed. The results can be summarized as follows. 1) Fracture appearance transition temperatures are 80.deg. C at the center part and 60.deg. C near surface of 12% Cr rotor, and 8.deg. C near surface of 1% Cr-Mo-V rotor. 2) Comparative rapid softening occurs at higher temperatures above 600.deg. C for 12% Cr steel and 550.deg. C for 1% Cr-Mo-V steel in tension tests. 3) Fatigue crack propagation rate of 12% Cr steel is almost same as that of 1% Cr-Mo-V steel at the same corresponding surface part of the rotors. The crack growth rate of center part of 12% Cr rotor is faster than near surface part of the rotor, and the crack growth rate at the load condition of R=0.04 is slower than that of the load condition of R=0.5 for both 12% Cr steel and 1% Cr-Mo-V steel. 4) Crack growth rate of radial direction near surface of 12% Cr rotor is faster than that of transverse direction at the same part because of the difference in residual stresses. 5) Both creep and fatigue strengths of 12% Cr steel are superior to those of 1% Cr-Mo-V steel and the difference is thought the effect of climb and glide controlled creep by solid solution of alloying elements and dispersion of carbides.

• 한국해양공학회지
• /
• 제3권2호
• /
• pp.625-625
• /
• 1989

To check technical improvement in the soundness and strength of 12% Cr steel rotor, a 25 tons of rotor with 65 tons of ingot was made in real size and was cut to pieces to take test samples, and the various mechanical tests such as impact, tensile, creep, and fatigue were carried out. The strengths are compared with those of 1% Cr-Mo-V rotor of same size. Microstructures of the samples are examined and reviewed. The results can be summarized as follows. 1) Fracture appearance transition temperatures are 80.deg. C at the center part and 60.deg. C near surface of 12% Cr rotor, and 8.deg. C near surface of 1% Cr-Mo-V rotor. 2) Comparative rapid softening occurs at higher temperatures above 600.deg. C for 12% Cr steel and 550.deg. C for 1% Cr-Mo-V steel in tension tests. 3) Fatigue crack propagation rate of 12% Cr steel is almost same as that of 1% Cr-Mo-V steel at the same corresponding surface part of the rotors. The crack growth rate of center part of 12% Cr rotor is faster than near surface part of the rotor, and the crack growth rate at the load condition of R=0.04 is slower than that of the load condition of R=0.5 for both 12% Cr steel and 1% Cr-Mo-V steel. 4) Crack growth rate of radial direction near surface of 12% Cr rotor is faster than that of transverse direction at the same part because of the difference in residual stresses. 5) Both creep and fatigue strengths of 12% Cr steel are superior to those of 1% Cr-Mo-V steel and the difference is thought the effect of climb and glide controlled creep by solid solution of alloying elements and dispersion of carbides.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 추계학술대회 초록집
• /
• pp.84.2-84.2
• /
• 2011

In this research, two thin film deposition techniques, Atomic Layer Deposition and Sputtering are carried out for the fabrication of Yittria Stabilized Zirconia electrolyte for thin film Solid Oxide Fuel Cell. Zirconium to Yittrium ratio for both cases is about 1/8. Scanning Electron Microscope(SEM) image shows that the growth rate per hour for Atomic Layer Deposition is faster than for sputtering. X-ray Photo-electron Spectroscopy(XPS) shows that the peaks of both Zirconia and Yittria shift towards higher bending energy for the case of Atomic Layer deposition and thus are more strongly attached to the substrate. Later, Nyquist plot was used to compare the conductivity of Yittria Stabilized Electrolyte for both cases. The conductivity at $300^{\circ}C$ for Atomic Layer Deposited Yittria Stabilized Zirconia is found to be $5{\times}10^{-4}S/cm$ while that for sputtered Yittria Stabilized Zirconia is $2{\times}10^{-5}S/cm$ at the same temperature. The reason for better performance for Atomic Layered YSZ is believed to be the Nano-structured layer fabrication that aids in along the plane conduction as compared to the columnarly structured Sputtered YSZ.

• 대한기계학회논문집B
• /
• 제24권11호
• /
• pp.1437-1446
• /
• 2000

A numerical analysis on the freeze coating process of a non-isothermal finite dimensional plate with a binary alloy is performed to investigate the growth and decay behavior of the solid and the mushy layer of the freeze coat and a complete procedure to calculate the process is obtained in this study. The continuously varying solid and mushy layers are immobilized by a coordinate transform and the resulting governing differential equations are solved by a finite difference technique. To account for the latent heat release and property change during solidification, proper phase change models are adopted. And the convection in the liquid melt is modeled as an appropriate heat transfer boundary condition at the liquid/mushy interface. The present results are compared with analytic solutions derived for the freeze coating of infinite dimensional plates and the discrepancy is found to be less than 0.5 percent in relative magnitude for all simulation cases. In addition the conservation of thermal energy is checked. The results show that the freeze coat grows proportional to the 1.2 square of axial position as predicted by analytic solutions ar first. But after the short period of initial growth, the growth rate of the freeze coat gradually decreases and finally the freeze coat starts to decay. The effects of various non-dimensional processing parameters on the behavior of freeze coat are also investigated.

• 자원리싸이클링
• /
• 제17권2호
• /
• pp.30-35
• /
• 2008

혼합 호산성 박테리아를 이용하여 리튬이온 밧데리 산업 폐기물로부터 코발트와 리튬의 침출을 연구하였다. 혼합 호산성 박테리아의 성장기질은 단체 황 및 2가 철이온으로 구성되어 있으며 미생물에 의한 금속의 침출은 폐기물에 존재하는 금속과 황산이온의 양자 반응 때문에 일어난다. 본 연구에서 12일간 미생물 침출반응시 고상 폐기물중 코발트의 80%, 리튬의 20%가 용해되었으며 고액비가 높을수록 금속의 독성으로 인하여 미생물의 성장은 억제된다. 단체 황의 농도가 높을 조건에서는 일부 황 분말이 용해되지 않으며 금속의 침출속도는 황의 증가에 따라 감소한다.

• 한국환경보건학회지
• /
• 제35권2호
• /
• pp.95-99
• /
• 2009

This study was performed to investigate the possible effect of garlic produced in Korea on the inhibition/reduction of growth of A. parasiticus, a toxigenic strain. The effect was studied using different concentrations of freeze-dried garlic in potato-dextrose agar (PDA) and/or in yeast-extract sucrose (YES) broth at $25^{\circ}C$ for 15 days. While inhibition of the fungal growth due to increasing the concentration of garlic was observed, the more remarkable effect was observed on the ninth day. Reduction of fungal diameter as a result of addition of garlic on PDA was observed to range between 3.4% to 20.1 % while reduction of mycelial weight in YES broth ranged from 9.9% to 30.5%. The 0.5% and 1.0% concentrations of garlic significantly reduced fungal diameter in PDA on the 9th day, while 0.1 %, 0.5%, and 1.0% concentrations of garlic significantly reduced the mycelial weight in YES broth (p<0.05). Dose-response relationships were observed between the concentration of garlic and inhibition of growth both in solid culture and in liquid culture. This study indicates that garlic could be an effective inhibitor at a human consumption level of the growth of A. parasiticus. More research is needed to study the inhibitory effects of the main active component of garlic.

• 한국결정성장학회지
• /
• 제4권2호
• /
• pp.169-177
• /
• 1994

결정성장된 시편의 농도분포를 제어하기 위해서는 초기융액의 농도를 균일하게 하여야 한다. 용질농도가 초기융액에 있어서 균일하지 않다면, 성장된 시편에 예측한 것과 다른 거시편석이 발생할 수 있다. 위 쪽의 온도가 높은 온도 구배를 갖고 아래로부터 응고를 진행시키는 Bridgman 방법으로 Al-Cu 합금을 성장시키는 경우, 성장된 시편의 어용질 농도분포가 초기응고 부분이 높고 을고가 진행됨에 따라 감소하는 경향을 갖는 것으로 관찰되었다. 이런 현사은 주괴가 녹으면서 도가니와 주괴의 틈으로 스며나온 Cu의 농도가 높은 융액이 주괴가 완전히 녹은 후의 대류에 의해 아래부분에 축적됨으로 발생했다. Al-Mg 합금의 경우 도가니와 주괴의 틈으로 스며나온 Mg의 농도가 높은 융액이 주괴가 완전히 녹은 후의 대류에 의해 떠오르면서 용질 농도분포가 성장중에 최소값을 가지는 것으로 나타났다. 이러한 거시편석을 억제하기 위하여, 균질화 처리 또는 도가니와 주괴의 틈을 없게 함으로 균일한 농도의 초기유액을 얻었다.

• Asian Pacific Journal of Cancer Prevention
• /
• 제15권8호
• /
• pp.3741-3745
• /
• 2014

Background: Emerging evidence implicates the platelet-derived growth factor-D (PDGF-D) in many types of human solid tumors. We investigated whether PDGF-D plays an important role in endometrial cancer (EC) in relation to clinicopathologic phenotype, angiogenesis, and patient prognosis. Materials and Methods: We analyzed PDGF-D protein expression by Western blotting in twenty-seven human endometrial cancer tissues, and matched normal endometrial controls collected at the third Affiliated hospital of Sun Yat-sen University during 2012-2013 (n=27). Immunohistochemical staining was performed using a human PDGF-D antibody on the endometrial cancer patients collected in the same facility during January 2001 and October 2013 (n=152). Patients were followed from the time of primary surgery in 2001-2013 until death or last follow-up. We correlated the PDGF-D expression levels with clinicopathologic parameters and prognosis in human endometrial cancer patients. Results: Compared with matched normal endometrial cases, PDGF-D was up-regulated in endometrial cancer. Expression of PDGF-D protein, found in 78% of the cases, was associated with nonendometrioid histologic type (p=0.028), FIGO stage III/IV (p=0.039), >50% solid tumor growth (p=0.048), pelvic LN metastasis (p=0.035) and ER and PR negativity (p=0.04 and 0.002). PDGF-D expression was also significantly associated with expression of VEGF-A (p=0.021). In multivariate analysis, PDGF-D expression proved to be an independent prognostic factor in addition to histologic grade and FIGO stage. Patients with high expression levels of PDGF-D had a significantly poorer overall survival rate compared with patients with no expression. Conclusions: PDGF-D expression is frequently up-regulated in endometrial cancer, and is associated with aggressive features and poor prognosis.