• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 D
• /
• pp.1270-1272
• /
• 1998

전기설비설계에 직접 활용할 수 있고, 초보자도 쉽게 사용할 수 있는 위 제목의 프로그램을 개발하였다. 산업전기설비에서 케이블과 접지설계는 안전하고 신뢰성있는 전기설비의 사용을 보장해 주어야함과 동시에 경제적인 설계가 되어야 한다. 이러한 산업체의 요구에 따라 신뢰성이 있고 표준화된 설계가 되도륵 전산 프로그램화하였다. 케이블 사이즈의 선정방법은 기존의 수계산에 의한 방법을 토대로 부하용도별로 권장되는 케이블/전선의 종류와 사이즈를 자동으로 선정하여 허용전류, 전압강하 요건을 만족시키도록 하였으며, 접지계산은 접지 종류별로 허용기준치 범위의 저항을 유지하도록 적절한 접지도체의 사이즈를 결정하고 대지저항율에 따른 접지저항을 계산하여 현장에서 실측치와도 비교할 수 있도록 하였다. 개발된 프로그램은 기존 계산결과와 상호 비교하는 유용성과 정확성의 검증과정을 거쳤으며, 사용자가 쉽게 사용할 수 있도록 GUI화면으로 구성한 점이 특징이다. 출력자료는 사용자의 필요에 따라 다양하게 출력할 수 있어 전산화의 잇점을 최대한 살렸다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 추계학술대회 논문집 전력기술부문
• /
• pp.319-322
• /
• 2002

Distance relay is operated in calculating line impedance. It can be worked accurately in overhead line. However, power cables or combined transmission lines need compensation for calculated impedance because cable systems have sheaths, grounding wires and sheath voltage limiters(SVLs) Neuro-fuzzy can be viewed either as a fuzay system, a neural network or fuzzy neural network and it can estimate the location of the fault accurately. In this paper, fault section and fault location can be classified and estimated in neuro- fuzzy inference system and neural network.

• 대한전기학회논문지:전력기술부문A
• /
• 제52권4호
• /
• pp.193-200
• /
• 2003

The use of underground transmission tables has continuously increased in densely inhabited urban and suburban area. Due to a increasing demand of underground cables, two or more circuits are installed in parallel for several kilometers. It, however, has not been realized that the sheath circulating current is generated in the system where a large number of cables are laid in the same route. In this paper, Author studied diversely the sheath circulating current on underground cables depending on the various length rate, the phase arrangement, and the grounding resistance of the sheath in the cross-bonded section. It was clear that very large circulating current is generated in cable systems due to unbalanced length rate and phase arrangement in the cross-bonded section.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제51권2호
• /
• pp.74-79
• /
• 2002

We have been analyzed the interference problems already in steady state, especially AC corrosion when the gas pipeline is burred with power cable in the same submarine tunnel. In the next stage, we analyze the induced voltage in a fault condition of 154[kV] underground T/L. This paper presents the results of them which are limitation of safety voltage. meodeling of power cables, gas pipeline and grounding systems, analysis of induced voltage in a fault condition, and protection of Power line system.

• 전기학회논문지
• /
• 제63권10호
• /
• pp.1364-1370
• /
• 2014

Power system fault analysis has been based on symmetrical component method, which describes power system elements by positive, negative and zero sequence impedance. Obtaining accurate line impedances as possible are very important for estimating fault current magnitude and setting distance relay accurately. Especially, accurate calculation of zero sequence impedance is important because most of transmission line faults are line-to-ground faults, not balanced three-phase fault. Since KEPCO has started measuring of transmission line impedance at 2005, it has been revealed that the measured and calculated line impedances are well agreed within reasonable accuracy. In case of underground transmission lines, however, large discrepancies in zero sequence impedance were observed occasionally. Since zero sequence impedance is an important input data for distance relay to locate faulted point correctly, it is urgently required to analyze, detect and consider countermeasures to the source of these discrepancies. In this paper, development of pre/post processor to ATP (Alternative Transient Program) version of EMTP (Electro-Magnetic Transient Program) for sequence impedance calculation was described. With the developed processor ATP-cable, effects of ground resistance and ECC (Earth Continuity Conductor) on sequence impedance were analyzed.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2003년도 학술대회논문집
• /
• pp.87-92
• /
• 2003

According to the realization of highly information dependent society, the recent building system is developed into the concept of suitable for management of intellegent work, which is demanded to unify of IBS(Intelligent Building System), IC(information communication), OA(office automation), BA(building automation) system and computer technology. However inspite of the presence arrester, cable shielding, insulated TR, filter, earth etc., in the IBS building for the cope with several surge and noise has several problems from the wrong operation of the equipment which caused from several surge, damage of equipment, and noise etc. And the miss operation caused by wrong earth works, which must be considered at first during the building construction. In order to minimize these problems, it's necessary that various earth project are performed effectively, and bonding methods between the mutual wiring of earth system and the equipments in the building should be improved sucessively. So in this paper, we analyze present domestic conditions of the earth technology in IBS building, and propose minimization method for the various surge and noise problem, and examine and analyze through the applied works.

• 한국항행학회논문지
• /
• 제22권5호
• /
• pp.351-358
• /
• 2018

본 연구에서는 개발된 모터 조립체의 누설 잡음신호 감쇠 방안을 시험을 통해 제안한다. 개발된 장치는 항공기 외부에 장착되어 안테나를 회전시키기 위한 장치로서 전자기 간섭 측면에서 MIL-STD-461F의 RE102 요구규격을 충족해야한다. RE102 시험결과를 통해 장치의 누설 잡음신호가 전원 및 제어 케이블을 통한 외부 유입과 모터 회전에 의해 발생됨을 확인하였다. 그리고 회전을 위해 내 외부의 물리적 차폐가 어려운 부분에서 잡음신호가 누설됨을 확인하였다. 누설 잡음신호에 대한 감쇠를 위해 장치 동작을 고려한 전기적 접지 보강, 전기적 차폐 구조를 적용하여 시험을 수행했고 규격 충족 여부를 확인하였다. 최종적으로 잡음누설 경로에 맞물리는 형태를 갖는 원형 주름 초크 구조와 전도성 그리스를 함께 적용하여 요구규격을 충족함을 확인하였다.