• 한국대기환경학회지
• /
• 제9권3호
• /
• pp.191-199
• /
• 1993

This paper describes the results of a systematic study to determine the characteristics of particle generated from various types of asbestos containing material(ACM) and manmade fiber material(MMFM) during operations of cutting and grinding in laboratory and workplace. Tests were conducted with a specially designed glove box which allowed complete sampling of the generated asbestos fibers. Specificially, air measurements were made during ACM and MMFM installation in building. All personal air samples collected were identified by polarized light microscopy(PLM), X-ray diffraction(XRD) and scanning electron microscope with energy dispersive X-ray analysis(SEM/EDXA). Also, the samples were counted by phase contrast microscope(PCM) in order to compare the results with the permissible exposure standard for workplace. Results indicate that the characterisitcs of fibers found in the roofing sheet, the ceiling and the wall insulation boards were identical to those of asbestos, while the characteristics of fibers found in the ceiling insulation board, the floor tile and the sprayed on insulation products in parking area were identical to those of asbestos, while the characteristics of fibers found in the ceiling insulation board, the floor tile and the sprayed on insulation products in parking area were identical to those of rock wool. The concentrations of airborne fibers from various building materials cut by a grinder for 5 minutes were in the ranges of 0.09 $\sim$ 1.71 fibers/cc(f/cc). The highest concentration(1.71f/cc) was found during grinding the wall insulation board which also contains rock wool. The airborne fiber concentrations generated by installing at workplace were ranged from 0.0009 to 0.029 f/cc. All asbestos fibers from the ceiling insulation board at workplace were less than 20$\mu$m in length and more than 20% of them had the average aspect ratio greater than 20. Therefore, for the purpose of decreasing asbestos and man-made fiber concentrations at the workplace, the ceiling and wall board should use strong binding material to increase the binding force with fiber. Also, the permissible exposure standard for workplace(2.0f/cc) in Korea should be constituted below the maximum avaiable concentration measured at glove box.

• 한국식품영양과학회지
• /
• 제46권6호
• /
• pp.730-738
• /
• 2017

본 연구에서는 커피 분쇄입도 조건에 따라 변화되는 커피의 이화학적 품질특성 및 휘발성 향기성분 변화에 미치는 영향을 조사하기 위하여 분쇄된 원두는 표준체(pore size 850, 600 및 $425{\mu}m$)를 사용하여 입자 크기를 whole bean(Control), $850{\mu}m$ 이상(coarse), $850{\sim}600{\mu}m$(medium), $600{\sim}425{\mu}m$(fine), $425{\mu}m$ 이하(very fine)의 크기가 되도록 사별하여 커피 추출 시료를 제조하였다. 품질특성으로는 pH, 산도, 갈색도, 색도, 총페놀, 카페인, 클로로겐산 함량 및 휘발성 화합물을 비교 분석하였다. pH 및 갈색도는 분쇄입도가 작아질수록 4.84~5.18, 0.257~0.284로 증가하였으나, 산도는 0.31~0.17로 감소하였다. 색도에서 L, a 값은 분쇄입도가 작아질수록 감소하였으나 L 값에서 분쇄입도별 유의적인 차이는 나타나지 않았으며 b 값은 분쇄입도가 제일 작은 very fine size($425{\mu}m$ 이하)에서 15.75로 가장 높은 황색도를 나타내었다. 색차에서 Control과 분쇄 커피분말과의 차이는 11 이상의 색차값을 나타내어 현저한 색의 차이 단계를 나타내었다. 총페놀, 카페인 및 클로로겐산 함량은 분쇄입도가 제일 작은 very fine size 입도($425{\mu}m$ 이하)에서 추출한 커피가 4.54 mg GAE/mL, 733.0 및 $383.7{\mu}g/mL$로 높은 함량을 나타내었고, 휘발성 화합물의 총함량도 100 mg/kg 이상 높게 검출되었다. 따라서 본 연구에서는 커피 추출의 기본 단계라고 할 수 있는 커피 분쇄입도 조건에 따라 변화되는 커피의 이화학적 품질특성을 상호 비교하고 향기성분 특성을 확인함으로써 커피 품질 평가에 관한 기초자료를 제시하였다고 생각된다.

• 한국광학회지
• /
• 제18권5호
• /
• pp.362-366
• /
• 2007

본 연구에서는 3 메가픽셀, 2.5배 줌 카메라폰 모듈용 비구면 유리렌즈 개발을 목적으로 실험계획법(DOE)을 적용하여 성형용 초경 코어의 연삭가공조건을 구하고, 이를 활용하여 비구면 Glass렌즈 성형용 초경합금(WC) 코어를 초정밀 연삭가공을 수행하였다. 또한 가공된 성형용 코어의 가공면 위에 이온증착법으로 다이아몬드상 탄소(Diamond-Like Carbon; DLC) 코팅을 수행하여 DLC 코팅이 성형용 코어의 형상정도(PV)와 표면조도(Ra)에 미치는 영향을 평가하였으며, 비구면 Glass렌즈를 동일한 조건에서 성형하여 성형렌즈의 광학적 특성을 비교하여 성형용 코어면의 DLC 코팅 효과에 대하여 검토하였다.

• 대한금속재료학회지
• /
• 제50권1호
• /
• pp.64-70
• /
• 2012

Samples of pure Mg, 76.5 wt%Mg-23.5 wt%Ni, and 71.5 wt%Mg-23.5 wt%Ni-5 wt%$Fe_2O_3$ were prepared by reactive mechanical grinding and their hydriding and dehydriding properties were then investigated. The reactive mechanical grinding of Mg with Ni is considered to facilitate nucleation and to shorten diffusion distances of hydrogen atoms. After hydriding-dehydriding cycling, the 76.5 wt%Mg-23.5 wt%Ni and 71.5 wt%Mg-23.5 wt%Ni-5 wt%$Fe_2O_3$ samples contained $Mg_2Ni$ phase. In addition to the effects of the creation of defects and the decrease in particle size, the addition of Ni increases the hydriding and dehydriding rates by the formation of $Mg_2Ni$. Expansion and contraction of the hydride-forming materials (Mg and $Mg_2Ni$) with the hydriding and dehydriding reactions are also considered to increase the hydriding and dehydriding rates of the mixture by forming defects and cracks leading to the fragmentation of particles. The reactive mechanical grinding of Mg-Ni alloy with $Fe_2O_3$ is considered to decrease the particle size.

• 한국분말재료학회지
• /
• 제17권4호
• /
• pp.319-325
• /
• 2010

Electrical discharge machining (EDM) is an attractive machining technique but it requires electrically conductive ceramic materials. In this study, Alumina matrix composites reinforced with CNTs were fabricated through CNT purification, mixing, compaction and spark plasma sintering (SPS) processes. $Al_2O_3$ nanocomposites with the different CNT concentrations were synthesized. The mechanical and electrical characteristics of $Al_2O_3$/CNTs composites were examined in order to apply the materials to the EDM process. In addition, micro-EDM using wire electrical discharge grinding (WEDG) was conducted under the various EDM parameters to investigate the machining characteristics of machined hole by Field Emission Scanning Electron Microscope (FE-SEM). The results show that $Al_2O_3$/CNTs 10%Vol. was more suitable than the other materials because high conductivity and large discharge energy caused violent sparks resulting in bad machining accuracy and surface quality.

• 펄프종이기술
• /
• 제47권2호
• /
• pp.61-69
• /
• 2015

A number of researches have been carried out regarding the utilization of nanocellulose(crystalline nanocellulose, microfibrillated cellulose, nanofibrillated cellulose) for the manufacture of various kinds of composites and functional products. However, only few research works on the manufacturing characteristics of nanocellulose could be found, although some companies started already the production of nanocellulose in commercial scale. However, the most important thing in commercializing of production and utilization of nanocellulose is to develop the economical and efficient process. Thus, this study was carried out in order to investigate the effects of refining, alkaline pre-treatment and grinder clearance on the characteristics of microfibrillated cellulose and energy consumption. There was no significant differences in crystalline index with the degree of microfibrillation. The initial fibrillation could be improved by refining pre-treatment, but its effect was not observed anymore since the fibrillation was done up to certain level by grinding. Refining pre-treatment did not improved the energy efficiency. Alkaline pre-treatment can be helpful because the swelling of pulp fiber will facilitate fibrillation. It was found that the decrease in grinder clearance was helpful to improve the energy efficiency.

• The Journal of Advanced Prosthodontics
• /
• 제14권6호
• /
• pp.335-345
• /
• 2022

PURPOSE. This in vitro study aimed to evaluate the surface characteristics of a full veneer crown fabricated chairside (CS) from a (Y, Nb)-TZP zirconia block in response to conventional zirconia grinding and polishing. MATERIALS AND METHODS. Zirconia crowns (n = 40) were first prepared and divided into two groups of materials: Labside (LS) and CS, after which each specimen went through a five-step grinding and polishing procedure. Following each surface treatment, surface characteristics were analyzed using confocal laser microscopy (CLSM), average surface roughness (Ra) values were processed from the profile data through Gaussian filtering, and X-ray diffraction pattern analysis was performed to evaluate the monoclinic (M) phase content. Then, a representative specimen was selected for field-emission scanning electron microscopy (FE-SEM), followed by a final analysis of the roughness and X-ray diffraction of the specimens using the independent t-test and repeated measures analysis of variance (RM-ANOVA). RESULTS. In every group, polishing significantly reduced the Ra values (P < .001). There was no significant difference in Ra between the polished state CS and LS. Furthermore, CLSM and FE-SEM investigations revealed that even though grain exposure was visible in CS specimens throughout the as-delivered and ground states, the exposure was reduced after polishing. Moreover, while no phase transformation was visible in the LS, phase transformation was visible in CS after every surface treatment, with the M phase content of the CS group showing a significant reduction after polishing (P < .001). CONCLUSION. Within the limits of this study, clinically acceptable level of surface finishing of (Y, Nb)-TZP can be achieved after conventional zirconia polishing sequence.

• 자원리싸이클링
• /
• 제11권2호
• /
• pp.28-35
• /
• 2002

충격형 분채기에 의한 폐프린트배선기판(PCBs)의 분쇄과정에서 일어나는 금속성분의 분쇄특성에 대한 연구가 수행되었다. PCBs로부터 금속성분들을 단체분리하기 위하여 -3 mm로 파쇄한 다음 충격형 분쇄기를 사용하여 분쇄하였으며 햄머의 회전속도가 금속성분의 분쇄에 미치는 영향을 관찰하였다. 동과 땜납 등과 같은 금속성분들의 입도분포 및 단체분리도를 조사하였다. 경사진동판을 사용하는 PCBs 분쇄물로부터 금속입자들의 형상분리에서 햄머의 회전속도와 입자크기가 미치는 영향을 검토하였다 61.3 m/s 햄머속도에서 동 성분은 +297$\mu$m 입자가 80% 이었지만 땜납성분은 -297$\mu$m 입자가 90%에 달했다. 형상분리법에 의한 금속입자의분리 시 햄머의 회전속도가 클수록 회수위치가 짧았으며 +297 $\mu$m 입자의 회수위치가 -297~+149$\mu$m 입자보다 짧았다. 회수위치가 짧을수록 금속입자의 구형도가 좋았으며 KI 값은 KI=1 로 증가하고, $\phi_{c}$ 값은 $\phi_{c}$ =1로 감소하였다.

• 한국식품조리과학회지
• /
• 제31권5호
• /
• pp.544-550
• /
• 2015

분질미, 연질미 및 경질미 쌀 품종을 건식제분과 습식제분 방법으로 제조한 쌀가루의 bakery 제품 활용도를 알아보기 위해서 제조한 잉글리쉬 머핀의 품질특성을 비교한 결과는 다음과 같다. 각각의 쌀가루로 제조한 잉글리쉬 머핀의 무게는 시료간에 유의한 차이가 없었고, 부피, 부피팽창율 및 비용적은 습식제분 분질미 쌀가루를 이용한 잉글리쉬 머핀에서 가장 높았으며, 건식제분 경질미 쌀가루로 제조한 잉글리쉬 머핀에서 가장 낮았다. 외관과 단면 형태를 살펴본 결과, 습식제분 분질미와 연질미 그리고 건식제분 분질미를 이용한 잉글리쉬 머핀이 가장 좋게 나타났다. 색도 측정 결과, L값은 건식제분 경질미를 이용한 잉글리쉬 머핀이 가장 높았고, b값은 건식제분 분질미를 이용한 잉글리쉬 머핀이 가장 높았다. 경도, 점착성 및 씹힘성은 습식제분 분질미를 이용한 잉글리쉬 머핀에서 가장 낮아 부드러웠고, 건식제분 경질미 쌀가루를 이용한 잉글리쉬 머핀에서 가장 높아 단단하게 나타났다. 관능검사 측정 결과, 색, 향미, 외형, 질감 및 전체적인 기호도는 습식제분 분질미 쌀가루를 이용한 잉글리쉬 머핀이 가장 높게 나타났고, 맛에 대한 기호도는 습식제분 연질미 쌀가루를 이용한 잉글리쉬 머핀이 가장 높게 나타났다.

• 한국정밀공학회지
• /
• 제13권10호
• /
• pp.139-145
• /
• 1996

The machining accuracy and performance is largely influenced by the static, dynamic and thermal characteristics of spindle systems in machine tools, because the spindle system is a intermedium for cutting force from tool and machine powef from motor. Large cutting force and power are transmitted by bearing with a point or line contact. So, the spindle system is the static and dynamic weakest point in machine structure. For improvement of static stiffness of spindle system can be changed design parameters, such as diameter of spindle, stiffness of bearing and bearing span. But for dynamic stiffness, the change of the design parameters are not useful. In this paper, the combined bearing arrangement is suggested for high damping spindle system. The combined bearing arrangement is composed of tandem double back to back arrangement type ball bearins and a high damping hydrostatic bearing. The variation of static deflection and amplitude in first natural frequency is evaluated with the location of hydrostatic bearing between front and rear ball bearing. The optimized location of hydrostatic bearing for high static and dynamic stiffness is determined rapidly and exactly using the mode shape and transfer function of spindle. The calculation of damping effect on vibration by unbalance of grinding wheel and pulley in optimized spindle system is carried out to verify the validity of the combined bearing arrangement. Finally, the simulation of grinding process show that the surface roughness of workpiece with high damping spindle system is 60% better than with ball bearing spindle system.