• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.6
• /
• pp.1139-1148
• /
• 2000

To treat and recycle a large quantity of converter slag. the milling properties of -14/ +24 mesh-sized slag has been considered. The optimal conditions in milling process were investigated for producing powder-type slag and the required consumption was derived for the economical grinding. The characteristics of milling processes were studied in the variation of the rotational speed, milling time, filling ratio of ball, and size and amount of feed. The grinding efficiency was also examined. The optimal rotational speed in this experimental condition was observed to be the value of 79% of critical speed. The extent of grinding was increased with increasing the grinding time. but the efficiency of milling was decreased with the time. 50% ball filling was shown to have the optimal grinding effect, and less amount and small-sized feed made the milling efficiency high. As the result, using Bond's equation, power required for efficient milling was considered and the highest value was observed in the condition of high grinding time and optimal rotational speed.

• Journal of Energy Engineering
• /
• v.28 no.1
• /
• pp.1-9
• /
• 2019

In the flue gas desulfurization process of the coal-fired power plant, the grinding efficiencies of the limestone as the sorbent for desulfurization were compared after BWI and HGI measurements. As a result, the grinding index of the domestic desulfurization limestone were linear inversely proportional relationship with decreasing BWI was observed with increasing HGI. There was a difference in grinding efficiency depending on the chemical composition and crystal structure. Therefore, it is considered that when grinding ability of limestone is measured, the grinding property of the sample can be confirmed even by using HGI which can be measured more easily than BWI which is difficult to measure and takes a long time. The desulfurization efficiency can be improved by selective utilization of limestone depending on the crushing characteristics.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.751-752
• /
• 2013

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.309-313
• /
• 2000

In order to meet the industrial requirement, precision grinding with brush tool has been applied. To analyze the brush tool characteristics, several parameters including numbers of brush string installed in a single holder, depth of cut and brush length have been changed. Several data from various source were acquired using AE, acceleration and tool dynamometer during the process. Consistent results revealing certain trend with respect to each process condition were observed.

• Resources Recycling
• /
• v.32 no.3
• /
• pp.18-25
• /
• 2023

Sericite was ground with or without additives (LiNO₃ or TiO₂) using a planetary mill. The resultant ground products included the average particle size of 2-3 ㎛ (sericite only or sericite+LiNO₃) and 0.5-0.6 ㎛ (sericite+TiO₂) were obtained within 10 minutes of grinding time. respectively. In the grinding of the sericite without any addictive, the particle size initially decreased, but, as grinding time elapsed thereafter, agglomerates were formed and D50 increased over 10 ㎛. In contrast, when the additive was added, the particle size decreased as the grinding time elapsed and any aggregation was relatively not noticeable, compared with the grinding of the sericite only. As a result of measuring the zeta potential for the raw or the ground samples, variation of the zeta potential values according to pH at the early stage of the grinding with the addictives was gentler than that at the final stage of grinding, which showed the relatively similar trend to the pH-zeta potential correlation in grinding of raw sericite. In addition, as a result of the disintegration experiment through ultrasonic excitation, D50 decreased rapidly only until the disintegration time of about 50 minutes.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.6
• /
• pp.97-101
• /
• 1998

In this study, The ultra-precision finishing system is applicable to all kind of the cylnderical workpiece products fast and easy. This system was applied to chrome coated steel to investigate the characteristic of grinding; (1) 3$mu extrm{m}$ of abrasive film is not use for grinding performance. (2) Grinding condition of coated chrome steel would set up differently, in 30~12${\mu}{\textrm}{m}$, in 9~5${\mu}{\textrm}{m}$. (3) The surface roughness of chrome coated steel was about Ra 0.0009${\mu}{\textrm}{m}$ in abrasive grain size 5${\mu}{\textrm}{m}$.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.4
• /
• pp.240-246
• /
• 2000

An in-process estimation of the ground surface roughness is a bottle-neck and an essential field in conventional grinding operation. We defined the dimensionless average roughness factor (D.A.R.F) that exhibits a roughness characteristics of ground surface. The D.A.R.F was composed easily of the absolute average and the standard deviation values which were the analytic parameters of the acoustic emission (AE) signal generated during the machining process. The theoretical equation between the surface roughness and the D.A.R.F has been derived from the linear regressive analysis and verified its availability through the experimentation on the surface grinding machine.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.24-27
• /
• 2002

The environmental problems by using coolant demanded the new cooling methods. As one of them, the studies on the finding with compressed cold air and oil mist have been done. The cooling method using compressed cold air was effective through going down the temperature of compressed air supplied below $-25^{\circ}$ and increasing the amount of compressed cold air, but had not enough cooling effect due to the low performance of lubrication. Therefore, the cooling methods using oil mist newly were suggested. This method can satisfy both cooling effect and lubrication with only small amount of coolant, also have the benefit in the point of decreasing the environmental pollution. This paper focused on analyzing the grinding characteristics of the cooling method using oil mist. The grinding test according to compressed cold air, oil mist spray pressure and oil mist supply direction were done.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.6
• /
• pp.96-102
• /
• 2000

The finishing process for dies and molds is an important process because it has influence on final quality of products. And it is difficult to automatize finishing process so that the process has depended on expert's skill until now. However, recently a study on development of die automatic finishing machine has been progressed, and actually this machine is applied to fabrication of die. But the research about tooling system is not enough and finishing tool must have high machining efficiency and adaptability of curved surface. So, this study investigated the application of conductive elastic tool which is composed of metal-resin bonded pellet and elastic backing material. The metal-resin bonded pellet is used to finish the surface by conventional mechanical grinding or electro-chemial grinding method. And elastic backing material is used to follow the curved surface. So conductive elastic tool has long lifetime, uniform removal rate and adaptability of curved surface.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.7
• /
• pp.7-12
• /
• 2003

각광을 받고 있는 광통신 분야의 핵심부품인 페룰은 일본이 전 세계의 95%를 장악하고 있다. 국내에서도 일부 업체에서 양산을 하고 있으나, 핵심 연삭공정에 사용되는 연삭 가공장비는 전량 수입되고 있는 실정이다. 페룰은 0.1∼0.3$\mu\textrm{m}$의 동심도, ${\pm}$ 0.2$\mu\textrm{m}$의 외경치수, 0.1$\mu\textrm{m}$대의 진원도와 원통도, 10nm의 표면 거칠기를 구현해야 세계적 경쟁력을 갖출 수 있는 초미세, 초정밀 기계가공 부품이다.(중략)