• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.10
• /
• pp.43-47
• /
• 2002

A simple optical signal to noise ratio monitoring method using fiber Bragg grating is proposed for monitoring performance of OADM. OSNR of each channel is determined by monitoring the optical power transmitted and reflected from fiber Bragg gratings, simultaneously. We have obtained OSNR with accuracy better than 0.8㏈ compared with OSA of 0.1nm optical resolution in the wide input power range between -6 ㏈m and -23㏈m per channel.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.12
• /
• pp.36-43
• /
• 2001

We evaluate the optical characteristics of planar distributed feedback (DFB) waveguides with quarter-wavelength phase-shifter. To analyze explicitly its band-pass and resonance properties, we present and newly develop a modal transmission-line theory (MTLT) based on Floquet's theorem and Babinet's principle. The numerical results reveal that this approach offers a simple and analytic algorithm to analyze either the filtering or the oscillating characteristic of DFB gratings with quarter-wavelength phase-shifter, and has a novel physical insight that may not be achieved in other approximating approaches

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.1
• /
• pp.21-28
• /
• 2004

We have demonstrated a low speed weigh-in motion system using FBG sensors and performed field test at a trial road. Technique, called identical chirped grating interrogation, have used for a demodulation relying on the mismatching of two identical broadband chirped gratings. We compensated the fluctuation of LED power and the temperature of sensor and used a lock-in amplifier to reduce effect of noise. We could design a bending plate that the measurement results are independent of position of weight. The FBG sensors weigh-in motion system showed linearity and reproducibility.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.120.2-120.2
• /
• 2015

We propose a novel direct writing technique with a femtosecond laser enabling selective modification of not only the morphology of conducting polymer thin films but also the orientation and alignment of the polymer crystal. Surface relief gratings resulting from photoexpansion on P3HT:PCBM and PEDOT:PSS thin films were fabricated by femtosecond laser direct writing. The photoexpansion was induced at laser fluence below the ablation threshold of the thin film. The morphology (size and shape) of photoexpansion could be quantitatively controlled by laser writing parameters such as focused beam size, writing speed, and laser fluence. GIWAX results showed that face-on P3HT crystals were largely increased in the photoexpansion in comparison with pristine region of the thin film. In addition, the face-on P3HTs in the photoexpansion were aligned with their orientation along the polarization of the laser. The micro-RAMAN spectra confirmed that neither chemical composition change nor the polymer chain breaking was observable after femtosecond laser irradiation. We believe that this laser direct writing technique opens a new door to the fabrication of more efficient OPVs via non-contact, toxic-free approach.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.2
• /
• pp.330-335
• /
• 2009

A fiber-optic liquid level sensor based on bending cantilever beam has been proposed. A fiber Bragg grating(FBG) embedded in the cantilever beam is used to sensing elements. The basic concept is elongation and constriction of the FBG corresponding to the liquid level variation. The best FBG position on the cantilever for obtaining the high sensitivity was 4 cm from the fixing point. When the liquid level moves up and down vertically, the Bragg wavelength is linearly shifted. But, the wavelength sensitivity of the FBG installed on the upper side of cantilever was four times better than that of the FBG equipped in the lateral side due to the difference of unit strain applied to the FBG. Intensity demodulation using the low-cost edge filter is used to interrogate the Bragg wavelength through converting the wavelength signals into the optical intensity ones. Experiment results show that the electrical output is exponentially proportional to the liquid level. But, it should be overcome for applying to the ships.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.645-648
• /
• 2005

Microscopy has enabled the development of many advanced technologies, and higher level microscopic techniques are required according to the increase of research in nano-technology and bio-technology fields. Therefore, in many applications, we need to measure the dimension of micro-scale parts accurately, not just to observe their shapes. To establish the meter-traceability in microscopy, gratings have been widely used as a magnification standard. KRISS provides the certification service of magnification standards using an optical diffractometer and a metrological AFM (MAFM). They are based on different measurement principles, and so can give complementary information for each other. In this paper, we describe the configuration of each system and measurement procedures to certificate grating pitch values of magnification standards. Several measurement results are presented, and the discussion about them are also given. Using the optical diffractometer, we can calibrate a grating specimen with uncertainty of less than 50 pm. The MAFM can measure a grating specimen of down to 100 nm pitch value, and the calibrated values usually have uncertainty less than 500 pm.

• Smart Structures and Systems
• /
• v.19 no.6
• /
• pp.625-631
• /
• 2017

In the fields of civil engineering and seismology, it is essential to detect and tracking the vibrations, and the fiber Bragg gratings (FBGs) are typically used as sensors to measure vibrations. Where, one of the most popular and detailed approaches to use FBGs as vibration sensors involves the use of cantilever beam designs, which adds a mass to measure low and moderate frequencies (from 20 Hz up to 1 kHz) with high sensitivities (greater than 10 pm/g). The design consists of a bending strain in the cantilever that is simultaneously transferred to the FBG, resulting in a shift in the wavelength that is proportional to the strain experienced by the cantilever. In this work, we present the experimental results of a vibration sensor design using a cantilever beam to generate an axial uniform strain in the FBG in-line with the vertical axis, which modifies the cantilever's natural frequency that allows the sensor to have a wide frequency broadband without losing sensitivity. This sensor achieved a sensitivity of about 339 pm/g and a natural frequency of 227.3 Hz. The presented design compared with the traditional cantilever beam-based FBG vibration sensors, has the advantages of a simple design for detection on vibration-sensitive structures and its physical parameters can be easily modified in order to satisfy the requirements of the desired vibration measurements.

• Journal of the Korea Computer Industry Society
• /
• v.4 no.12
• /
• pp.943-952
• /
• 2003

GDS(Grating automatic Drawing System), which is an automatic design system of metal products called grating, is a system that produces various detailed drawings on the basis of information within a Plan Drawing that represents layout of the gratings such as locations, shapes, directions, etc. However, automatically produced drawings by GDS do not fully satisfy the standard of the general dimension marking method used among the layout designers. The lack of this standard quality mainly results from the fact that overlapping among dimension markings appears frequently. To solve the overlapping problem we applied the rule-based expert system which uses the expert's knowledges and facts to solve the problems. The rules for the expert system are designed based on the expertise of skilled layout designers within the grating production lines.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.7
• /
• pp.54-60
• /
• 2007

We constructed a fiber-optic temperature sensor system using a sensor array with 15 fiber Bragg gratings for distributed temperature monitoring in electrical power systems. A polynomial fitting algorithm was used to compensate the nonlinear action of the MEMS tuneable wavelength filter used for Bragg wavelength demodulation Fixed passband wavelengths from a Fabry-Perot ITU filter were used as reference wavelengths for the fitting algorithm which obtained constant accuracy regardless of the wavelength scanning range and frequency. About 0.18[%] of linearity error compared to reference thermocouple thermometer has been obtained in the preliminary experimental results.

• The Transactions of the Korea Information Processing Society
• /
• v.5 no.1
• /
• pp.236-248
• /
• 1998

Human observers perceive a contour where no line or edge is given, such as the border between gratings of thin lines offset by half a cycle. Illusory contours occur in a wide variety of circumstances in nature. A common factor in all such figures is the perception of a surface or contour occluding part of a background, i.e. illusory contours are always accompanied by illusory surfaces. Some examples about these kinds of figures are given by Kanizsa's triangle or square. In this paper, we proposed a neural network model for forming(extracting) the illusory surfaces, based on the mechanism of feature extraction found in a mammals' visual pathway. It will be shown that the model can extract the illusory surfaces from illusory contours successfully.