• Korean Journal of Environmental Agriculture
• /
• v.11 no.2
• /
• pp.155-162
• /
• 1992

In order to extend the releasing period of granular formulation to approximately 20 days, the KC-6620-adsorbed granules were formulated with carriers and polyethylene glycol as adjuvant. The releasing rates of active ingredient from the formulations were evaluated in aqueous medium. The baked bentonite was found most effective carrier to sustain the release of KC-6620. Due to, however, low releasing rate of active ingredient after 20 days, bentonite formulation appeared to be of no practical for the short-term sustained release of KC-6620. The increased pore volume of bentonite granular formulation by adding pyrophyllite increased remarkably the released amount of KC-6620 from bentonite-pyrophyllite(4 : 6) granule up to 85% of total active ingredient incorporated. Addition of polyethylene glycol to the bentonite-pyrophyllite granule further increased the releasing rate of KC-6620. With KC-6620 content in the bentonite-pyrophyllite(4 : 6) granule, the releasing rate of active ingredient was markedly reduced.

• Geomechanics and Engineering
• /
• v.27 no.6
• /
• pp.583-594
• /
• 2021

The gas permeability behavior of unsaturated bentonite-based materials is of major importance for ensuring effective sealing of high-level radwaste repositories. This study investigated this by taking a sample of Granular Bentonite Material (GBM) at the end of the Engineered Barrier Emplacement (EB) experiment in the Opalinus Clay, placing it under different humidity conditions until it achieved equilibration, and testing the change in the gas permeability under loading and unloading. Environmental humidity is shown to have a significant effect on the water content, saturation, porosity and dry density of GBM and to affect its gas permeability. Higher sensitivity to confining pressure is exhibited by samples equilibrated at higher relative humidity (RH). It should be noted that for the sample at RH=98%, when the confining pressure is raised from 1 MPa to 6 MPa, gas permeability can be reduced from 10^-16 m² to 10^-19 m², which is close to the requirements of gas tightness. Due to higher water content and easier compressibility, samples equilibrated under higher RH show greater irreversibility during the loading and unloading process. The effective gas permeability of highly saturated samples can be increased by 2-3 orders of magnitude after 105℃ drying. In addition, cracks possibly occurred during the dehydration and drying process will become the main channel for gas migration, which will greatly affect the sealing performance of GBM.

• Nuclear Engineering and Technology
• /
• v.54 no.11
• /
• pp.4005-4012
• /
• 2022

As high-level radioactive waste (HLW) generated from nuclear power plants is harmful to the human body, it must be safely disposed of by an engineered barrier system consisting of disposal canisters and buffer and backfill materials. A gap exists between the canister and buffer material in a HLW repository and between the buffer material and natural rock-this gap may reduce the water-blocking ability and heat transfer efficiency of the engineered barrier materials. Herein, the basic characteristics and thermal properties of granular bentonite, a candidate gap-filling material, were investigated, and their effects on the temperature change of the buffer material were analyzed numerically. Heat transfer by air conduction and convection in the gap were considered simultaneously. Moreover, by applying the Korean reference disposal system, changes in the properties of the buffer material were derived, and the basic design of the engineered barrier system was presented according to the gap filling material (GFM). The findings showed that a GFM with high initial thermal conductivity must be filled in the space between the buffer material and rock. Moreover, the target dry density of the buffer material varied according to the initial wet density, specific gravity, and water content values of the GFM.

• The Journal of Natural Sciences
• /
• v.13 no.1
• /
• pp.35-50
• /
• 2003

Granular clay minerals for adsorption of the organic dye prepared a Na-Bentonite and optimum condition calcined temperature $700^{\circ}C$ and polyvinyl alcohol quantity was 25%. Granular clay mineral stable range was pH3 to pH9 and specific area was $83m^2/g$. The adsorption of the organic dye on the Granular clay mineral showed result good adsorption with acid medium and then enthalpy was -3.36 ~ -0.84 kcal/mol. It was exhibit typical physical adsorption.

• Geomechanics and Engineering
• /
• v.28 no.2
• /
• pp.135-143
• /
• 2022

Soils are natural granular materials whose mechanical properties differ according to the size and composition of the particles, so soils exhibit an obvious scale effect. Traditional soil mechanics is based on continuum mechanics, which can not reflect the impact of particle size on soil mechanics. On that basis, a matrix-reinforcing-particle cell model is established in which the reinforcing particles are larger-diameter sand particles and the matrix comprises smaller-diameter bentonite particles. Since these two types of particles deform differently under shear stress, a new shear-strength theory under direct shear that considers the stress concentration and bypass phenomena of the matrix is established. In order to verify the rationality of this theory, a series of direct shear tests with different reinforcing particle diameter and volume fraction ratio are carried out. Theoretical analysis and experimental results showed that the interaction among particles of differing size and composition is the basic reason for the size effect of soils. Furthermore, the stress concentration and bypass phenomena of the matrix enhance the shear strength of a soil, and the volume ratio of reinforcing particles has an obvious impact on the shear strength. In addition, the newly proposed shear-strength theory agrees well with experimental values.

• The Korean Journal of Pesticide Science
• /
• v.2 no.3
• /
• pp.36-44
• /
• 1998

To develope cost-effective new granular formulation of mixture with 7.0% chlomethoxyfen and 3.5% butachlor, this study was conducted by investigation of floatability, dispersibility or collapsability and released concentration of active ingredients in water and bio-efficacies of the granules formulated by different formulation methods compared to commercial pellet-extruded granules. They were formulated by coating on or impregnation into extruded pellets, sands and zeolites with two active ingredients, binders, friction reducer, dispersing agents and bentonite. Pellet-coated method showed similar floatability, collapsability and bio-efficacy to the commercial pellet-extruded one or better than that but unstable patterns of released concentration of chlomethoxyfen because of easy isolation of coated technical particles from the surface of granules. Sand-coated methods showed similar physical properties, released pattern of two active ingredients, and bio-efficacy to the commercial one. Liquid binders and/or dispersing agents are more important than powdered ones to control released concentration of active ingredients from the granule mixtures, to improve the floatability and dispersibility, and to show good bio-efficacy. Sand-coated one might be a suitable method if types and amount of liquid binders and dispersing agents are selected.

• Tunnel and Underground Space
• /
• v.33 no.6
• /
• pp.435-444
• /
• 2023

In the licensing application for the deep geological disposal system of high-level radioactive waste in Finland, the disposal tunnel backfilling has been changed from the block/pellet (for the construction) to the granular type (for the operation). Accordingly, for establishing the design concept for backfilling, it is necessary to examine applicability to the domestic facility through analyzing problems of the existing method and improvements in the alternative design. In this paper, we first reviewed the principal studies conducted for changing the backfill method in the licensing process of the Finnish facility, and identified the expected problems in applying the block/pellet backfill method. In addition, we derived the evaluation factors to be considered in terms of technical and operational aspects for the backfilling solution, and then conducted a comparative analysis for two types of backfill methods. This analysis confirmed the overall superiority of the design change. It is expected that these results could be utilized as the technical basis for deriving the optimum design plan in development process of the Korean-specific deep disposal facility. However, applicability should be reviewed in advance based on the latest technical data for the detailed evaluation factors that must be considered for selecting the backfilling method.