• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 춘계 학술발표회 논문집
• /
• pp.219-228
• /
• 2006

In urban areas, tunnelling induced ground deformations, particularly ground settlements should be considered in order to minimize the damage of adjacent structures. Therefore, an appropriate monitoring system for the tunnel construction should be setup at the planning or design stage. A number of studies on ground settlements due to tunnelling in soft ground have been carried out so far. However, most studies have focused on clay soil rather than sand soil. In particular, a few studies on behaviour of subsurface deformations in granular material have been reported. In this study, two-dimensional laboratory model test with aluminium rods regarded as continuum granular material and close range photogrammetric technique, and numerical analysis were carried out in order to identify the behaviour of subsurface deformations due to shallow tunnelling. Direction and magnitude of displacement vectors from the model test was identical to the numerical analysis. In particular, the vector direction was appeared to be toward a point below the tunnel invert level. A narrow 'chimney or tulip like' pattern of vertical displacement was confirmed by both the model test and numerical analysis. This is consistent with the field data. In addition to the qualitative comparison, the quantitative comparison of subsurface settlements according to 2D volume loss showed good agreement between the model test and numerical analysis. Therefore, close range photogrammetric technique applied in the model test may be used to validate the result from the continuum numerical analysis.

• 대한토목학회논문집
• /
• 제14권4호
• /
• pp.827-838
• /
• 1994

많은 포장구조 거동 모델은 입상재료의 거동을 묘사하는 구성방정식에 의존하고 있다. 본 연구에서는 비행장 포장의 입상재료 기층의 거동 예측을 위하여, 체적응력(bulk stress)과 팔면체 전단응력(octahedral shear stress)의 함수로 표시된 구성모델이 제안되었다. 이 모델의 특징은 비선형거동을 정확히 예측할 수 있고, 모델상수를 간단히 구할 수 있으며 전단효과에 의한 회복탄성계수의 감소현상을 나타낼 수 있다. 실내시험을 통하여 입상재료의 비선행 회복탄성거동을 관찰하였으며, 제안된 모델을 입증하기 위해 회복탄성계수를 측정하였다. 체적응력과 축차응력이 회복탄성계수의 변화에 가장 주요한 변수임이 관찰되었으며, 실내시험 결과 제안된 모델식에 의한 회복탄성계수의 예측치가 실측치와 잘 일치함을 알 수 있었다. 따라서 제안된 모델식은 비행장 포장에서 일어날 수 있는 광범위한 응력조건하의 입상재료의 회복탄성거동을 잘 묘사할 수 있음을 알 수 있다.

• 대한수의학회지
• /
• 제63권4호
• /
• pp.32.1-32.4
• /
• 2023

Granular cell tumor was described in the testis of two rabbits. Testis from each rabbit was surgically removed and submitted for histopathological diagnosis. Both testes were about 2.0 cm in diameter, firm, and tan. Microscopically, testicular mass consisted of compact sheets of round to polygonal and occasional spindle-shaped cells. The neoplastic cells contain a large amount of eosinophilic granular material in the cytoplasm. The cytoplasmic eosinophilic granules were positive for periodic acid Schiff stain. Immunohistochemically, the neoplastic cells were immunoreactive to Melan-A and vimentin. Based on these results, the testicular mass was diagnosed as a granular cell tumor.

• 한국지반환경공학회 논문집
• /
• 제13권10호
• /
• pp.55-62
• /
• 2012

본 연구에서는 개별요소해석 프로그램인 $PFC^{3D}$를 이용하여 대입경 조립재료의 특정 입도분포를 구현하는 알고리즘을 개발하였다. 기존의 입자 형상이나 입도를 구현하기 위해 사용되었던 clump logic 또는 cluster logic을 사용하지 않으며 요소의 경계면 이탈 현상과 경계면 파괴 등을 방지할 수 있는 초기 개별요소 모델링 기법을 고안하였다. 최종적으로 대입경 조립재료에 대한 대형 삼축압축시험을 수치 모델링하고 실내시험 결과와 비교하였다. 해석 결과, 실제 시료의 입도분포와 매우 흡사한 분포의 개별요소를 생성할 수 있었고, 적정 미시물성치 산정 과정(calibration)을 통해 다양한 구속응력 조건에 대한 대입경 조립재료의 특정 입도분포하에서의 전체적인 수치 모델링이 가능하였다.

• 한국분말재료학회지
• /
• 제10권5호
• /
• pp.349-352
• /
• 2003

This study examined the correlation of various operational factors including reaction temperature and the quantity of reductant and diluent with the characteristics of powder using $K_2$ TaF$_{7}$ as feed materials, Na as a reductant and KCl/KF as a diluent. Also to control the particle size and shape, external supply system developed, it can provide a feed material and a reductant at a fixed quantity and evaluated the characteristics of tantalum powder. When the external supply system was applied instead of the batch type process that charges feed material, reductant and diluent at the same time, it was possible to induce regular reduction reaction between feed material and reductant, which increased the recovery rate and reduced the mixture of impurities. In particular, the application of the external supply system enabled the control of reaction temperature and reaction speed according to the feeding rate of feed material during reduced reaction, and resultantly it enabled the manufacturing of granular-shaped powder with a regular granularity of 2∼3 ${\mu}{\textrm}{m}$ and purity of 99.5%.

• 상하수도학회지
• /
• 제33권1호
• /
• pp.9-16
• /
• 2019

The algal blooms in stagnant streams and lakes have caused many problems. Excessive algae leads to disturbance of ecosystem and overload of water treatment processes. Therefore, phosphorus(P), source of algal blooms, should be controlled. In this study, a filtration trench has been developed to convert dissolved phosphorus into hydroxyapatite(HAP) so that it could be crystallized on the surface of 'phosphorus removal granular material'; and residual particulate phosphorus could be removed by additional precipitation and filtration. The front and rear parts of filtration trench consisted of 'phosphorus removal granular material contact bed' and 'limestone filtration bed', respectively. As a result of the column test using phosphorus removal granular material and limestone serially, $PO_4-P$ was removed more than 90% when EBCT(empty bed contact time) of the contact bed was over 20 minutes; and T-P represented 60% of removal efficiency when total EBCT was over 1.5 hours. The results of column tests to figure out the sedimentation characteristics showed that more than 90% of particulate phosphorus could be removed within 24 hours. It was necessary to optimize the filtration part in order to increase removal efficiency of T-P additionally. Also, it was confirmed through the simulation of Visual MINTEQ that most of particulate phosphorus in the column tests is the form of HAP. Based on the results of the study, it could be suggested that the design parameters are over 0.5 hour of EBCT for phosphorus removal granular material contact bed and over 1.5 hours of EBCT for limestone filtration bed.

• 한국지반공학회지:지반
• /
• 제10권4호
• /
• pp.103-118
• /
• 1994

입자물질의 빠른 움직임을 미시적으로 관찰하고 이를 연속체이론에 적용하였다. 두 입자의 상호충돌현상에서 두 종류의 시간 즉 미행시간과 접촉시간을 나누었다. 전자는 시간에 따라 변하는 움직임과 체적의 변화를 나타내며, 후자는 두 입자가 접촉시에 걸린 시간을 뜻하며 이 크기는 입자의 탄성성질을 나타낸다. 이러한 두 종류의 시간을 이용하여 4개의 상태변수 즉 압축응력, 점성, 에너지전달률 그리고 에너지손실률로서 동력학적 구조거동식을 세웠다. 연속체이론의 질량, 운동량 및 에너지방정식을 위의 상태변수로서 표기하고 이를 다시 두 가지의 모델에 적용한 결과 탄성성질로 인한 이완 및 에너지 흡수현상이 나타났다.

• Journal of Advanced Research in Ocean Engineering
• /
• 제2권2호
• /
• pp.86-98
• /
• 2016

In this study, after the installation of a subsea pipeline, backfilling was performed in the trenched area. During these operations, a stability problem in the subsea pipeline occurred. The pipeline was directly impacted by environmental loading such as waves and currents that were caused by backfill material when scouring or sediment transport and siltation was carried out. Therefore, this study reviewed whether trenching was necessary, and conducted research into an indigenous seabed property that contains granular soil. A study of cohesive soil was also conducted in order to cross-correlate after calculating the values of the critical Shields parameter relevant to elements of the external environment such as waves and current, and the shear Shields parameter that depends on the actual shearing stress. In case of 1), sedimentation or erosion does not occur. In the case of 2), partial sedimentation or erosion occurs. If the case is 3), full sedimentation or erosion occurs. Therefore, in the cases of 1) or 2), problems in structural subsea pipeline stability will not occur even if partial sedimentation or erosion occurs. This should be reflected particularly in cases with granular and cohesive soil when a reduction in shear strength occurs by cyclic currents and waves. In addition, since backfilling material does not affect the original seabed shear strength, a set-up factor should be considered to use a reduced of the shear strength in the original seabed.

• 상하수도학회지
• /
• 제32권5호
• /
• pp.399-409
• /
• 2018

Prussian blue is known as a superior material for selective adsorption of radioactive cesium ions; however, the separation of Prussian blue from aqueous suspension, due to particle size of around several tens of nanometers, is a hurdle that must be overcome. Therefore, this study aims to develop granule type adsorbent material containing Prussian blue in order to selectively adsorb and remove radioactive cesium in water. The surface of granular activated carbon was grafted using a covalent organic polymer (COP-19) in order to enhance Prussian blue immobilization. To maximize the degree of immobilization and minimize subsequent detachment of Prussian blue, several immobilization pathways were evaluated. As a result, the highest cesium adsorption performance was achieved when Prussian blue was synthesized in-situ without solid-liquid separation step during synthesis. The sample obtained under optimal conditions was further analyzed by scanning electron microscope-energy dispersive spectrometry, and it was confirmed that Prussian blue, which is about 9.7% of the total weight, was fixed on the surface of the activated carbon; this level of fixing represented a two-fold improvement compared to before COP-19 modification. In addition, an elution test was carried out to evaluate the stability of Prussian blue. Leaching of Prussian blue and cesium decreased by 1/2 and 1/3, respectively, compared to those levels before modification, showing increased stability due to COP-19 grafting. The Prussian blue based adsorbent material developed in this study is expected to be useful as a decontamination material to mitigate the release of radioactive materials.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회
• /
• pp.1182-1189
• /
• 2010

The mechanical behavior of a granular material is governed by the applying effective stresses and its skeletal structure which is considered to be the packing of particles giving overall density and degree of anisotropic. Factors that affect soil packing are the particle size, size distribution and shape, and the arrangement of grain contact. Soil particle size and shape are the most important factor, but difficult to quantify. In this study, 2D Fourier analysis is applied to quantify the shape of granular particles. Jumunjin sand was used in the experiment and particle images are captured using an optical microscope. The results showed that three lower order Fourier descriptor are closely related with roundness, sphericity of the granular particle. Also statistical approach is used to determine roundness, form factor, elongation ratio, roughness of Jumunjin sand.