• Korean Journal of Hydrosciences
• /
• v.1
• /
• pp.49-60
• /
• 1990

Manning's roughness factor to flow in sand-bed channels may be divided into the grain roughness factor nd the form roughness factor. The grain roughness factor may be dedermined by using Keulegan's formula. By using available experimental data, it was found there is a unique relationship between the form roughness and the hydraulic radius to sediment particle size ratio for a given value of the Froude number. The form roughness and the bed form may be determined by using this unique relationship. The technique for engineering applications of the results appears to be quite simple.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.23 no.4
• /
• pp.304-312
• /
• 2011

Grain size analysis was conducted for a total of 402 surface sediments collected from 67 sites along three (upper, middle, and lower) transects corresponding to the high-, mid-, and low-intertidal zone of beach on the Sinjado, Nakdong River estuary in Nov. 2005 and May 2006. Sinja-do beach sediments showed uni-modal grain size distributions, in which the mode of $3.0{\phi}$ was dominant in 2005 whereas the mode of $2.5{\phi}$ in 2006. This coarsening trend was more remarkable in the western side of beach as well as in the mid- and low-intertidal zone. In this study, we focused on investigating characteristics of sediment size changes on the basis of transect data that differ in tidal elevation. For this purpose, a statistical test was applied for transect by transect comparison of grain size parameters such as mean, sorting, and skewness. Mean values between middle and lower transect, sorting values between upper and lower transect, and skewness values over the beach reflected statistically significant temporal changes. Also, mean and skewness parameters showed an inverse relationship which was more stronger in 2006 than in 2005. Temporal changes in Sinja-do beach sediments resulted in decrease of mean and sorting values but increase of skewness values, intensifying the inverse relationship between mean and skewness parameters.

• Journal of Environmental Impact Assessment
• /
• v.18 no.3
• /
• pp.171-183
• /
• 2009

This study aims to analyze the sedimentary environment change in mid-channel bar of the lower Geum river basin after the construction of the estuary barrage using multi-temporal satellite data and GIS. The sedimentary environment changes were observed in mid-channel bar areas. The mid-channel bar F was found to have been newly formed for 10 years(1996-2006), whereas the mid-channel bar B located between mid-channel bar A and C has disappeared by erosion during the same periods. When examined by section, the areas of the mid-channel bar in the upper stream section from the Yipo's reference point generally increased due to the prevailing sedimentary environments, and those of the downstream section decreased where corrosive environments are dominant. In ternms of the centroid movement, the mid-channel bars grew up toward the downstream by switching erosion and accumulation, as sedimentation was prevailing in the downstream area of mid-channel bars and corrosion was dominant in the upper stream. Through grain size analysis, the study areas are divided into three sections according to the average grain size. In Section I, the mid-channel bars were formed as a result of sedimentary process of tides in the past. In Section II, the mid-channel bars were formed partly through the sedimentary process of rivers although the sedimentary process of tides is prevailing. In Section III, the mid-channel bars were formed mainly through the sedimentary process of rivers, even if it showed the sedimentary process of tides in the past.

• The Journal of Advanced Prosthodontics
• /
• v.8 no.3
• /
• pp.181-186
• /
• 2016

PURPOSE. The opacity of zirconia is an esthetic disadvantage that hinders achieving natural and shade-matched restorations. The aim of this study was to evaluate the translucency of non-colored and colored framework zirconia and monolithic zirconia. MATERIALS AND METHODS. The three groups tested were: non-colored framework zirconia, colored framework zirconia with the A3 shade according to Vita Classic Scale, and monolithic zirconia (n=5). The specimens were fabricated in the dimensions of $15{\times}12{\times}0.5mm$. A spectrophotometer was used to measure the contrast ratio, which is indicative of translucency. Three measurements were made to obtain the contrast ratios of the materials over a white background ($L^*w$) and a black background ($L^*b$). The data were analyzed using the one-way analysis of variance and Tukey HSD tests. One specimen from each group was chosen for scanning electron microscope analysis. The determined areas of the SEM images were divided by the number of grains in order to calculate the mean grain size. RESULTS. Statistically significant differences were observed among all groups (P<.05). Non-colored zirconia had the highest translucency with a contrast ratio of 0.75, while monolithic zirconia had the lowest translucency with a contrast ratio of 0.8. The mean grain sizes of the non-colored, colored, and monolithic zirconia were 233, 256, and 361 nm, respectively. CONCLUSION. The translucency of the zirconia was affected by the coloring procedure and the grain size. Although monolithic zirconia may not be the best esthetic material for the anterior region, it may serve as an alternative in the posterior region for the bilayered zirconia restorations.

• Korean Journal of Metals and Materials
• /
• v.47 no.9
• /
• pp.523-532
• /
• 2009

In this study, four API X80 linepipe steel specimens were fabricated with varying cooling rates and finish cooling temperatures, and their microstructures and crystallographic orientations were analyzed to investigate the effects of cooling conditions on their tensile and Charpy impact properties. All the specimens consisted of acicular ferrite, granular bainite, and secondary phases such as martensite and martensiteaustenite constituent. The volume fraction of secondary phases increased with increasing cooling rate, and the higher finish cooling temperature resulted in the reduction in volume fraction and grain size of secondary phases. According to the crystallographic orientation analysis data, the effective grain size and unit crack path decreased as fine acicular ferrites having a large amount of high-angle grain boundaries were homogeneously formed, thereby leading to the improvement of Charpy impact properties. The specimen fabricated with the higher cooling rate and lower finish cooling temperature had the highest upper shelf energy and the lowest energy transition temperature because it contained a large amount of fine secondary phases homogeneously distributed inside fine acicular ferrites, while its tensile properties well maintained.

• The Journal of the Acoustical Society of Korea
• /
• v.34 no.6
• /
• pp.423-431
• /
• 2015

KIOST-HYU joint acoustics experiment was performed on the western shallow water off the Taean peninsula in the Yellow Sea in May 2013. In this paper, mid-frequency (6~16 kHz) bottom loss data measured in a grazing angle range of $17{\sim}60^{\circ}$ are presented and compared to the predictions obtained using a Rayleigh reflection model. The sediment structure of the experimental site was characterized by multi-layered sediment and the components of the surficial sediment consisted of various types of particles with a mean grain size of $5.9{\phi}$. The model predictions obtained using the mean grain size were not in agreement with the measured bottom loss, and those obtained using the grain size of $4{\phi}$, which was estimated by an inversion process, showed a best fit to the measurements. It would be because the standard deviation of the gain-size distribution of surficial sediment is $4.3{\phi}$, which is much larger than those of other areas around the experimental site. Finally, the model predictions obtained using the geoacoustic parameters estimated from the inversion process for the surficial sediment layer and those corresponding to the mean grain size of $1.3{\phi}$ for lower layer are reasonably agreement with the measured bottom loss data.

• The Korean Journal of Quaternary Research
• /
• v.21 no.2
• /
• pp.77-79
• /
• 2007

The source regions of Asian Dusts (Yellow Sands) in the western part of China are investigated, and the soil samples are collected samples for approximately 15 days during the spring of 2005. Particle sizes of sediments are analyzed and compared with each other. These grain-size analyses from the source areas can be compared Particle sizes between loess deposits and desert sands in western part of China and desert areas show distinctive differences. Loess deposits are predominantly composed of fine sands and silts. The distinction between the final characteristics of Asian Dust particles arrived in Korea and characteristics during transportation can be recognized comparison with the Asian Dust particles collected where the dust particles settled down. The characteristics of Asian Dust particle sizes can provide the basic information regarding the transportation history from the source region.

• Journal of the Korean institute of surface engineering
• /
• v.31 no.5
• /
• pp.286-296
• /
• 1998

Galvannealing is becomming the main stream of the coating technology applied to automobile outer and inner panels due to its low cost and easy application applied to automobile outer and inner panels due to its low cost and easy application in thick Zn coating, compared to electro galvanizing. Despite of filed up data with an experience in this field, galvannealing in thick Zn coating is getting more difficult because of the absence of Fe deposition in Zn coating. As a result, it exhibits, with different steel sheet and grain size there is a proper temperature range which is good for the tarket coating thickness of galvannealing. In case of 1,200mm wide and 0.77 mm thick extra low carbon steel with 20$mu extrm{m}$ grain size, its proper temperature range for galvannealing of one side 60g/$\textrm{m}^2$ is 470-$480^{\circ}C$.

• Proceedings of the KSRS Conference
• /
• 2002.10a
• /
• pp.734-738
• /
• 2002

We present spectral characteristics of tidal flat sediments and algal mat that were tested in the Gomso and Saemangum tidal flats, Korea. The objective of this study is to investigate the spectral reflectance and the radar scattering modeling in the tidal flats. Ground truth data obtained in the tidal flats include grain size, soil moisture content and its variation with time, surface roughness, chlorophyll, ground leveling, and field spectral reflectance measurement. The concept of an effective exposed area (EEA) is introduced to accommodate the effect of remnant surface water, and it seriously affects the reflection of short wavelength infrared and microwave. The nin size of 0.0625 mm has been normally used as a critical size of mud and sand discrimination. But we propose here that 0.25 mm is more practical grain size criterion to discriminate by remote sensing. Algal mat is the primary product in tidal flats, and it is found to be very important to understand spectral characteristics for tidal flat remote sensing. We have also conducted radar scattering modeling, and showed L-band HV-polarization would be the most effective combination.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.146-146
• /
• 2010

Electrical properties of Large-grain-size TIT with 7/7 ${\mu}m$ channel width and length which gate insulator is made of 20nm $SiO_2$ and 80nm $SiN_x$. was fabricated and measured with Large-grain-size technic(MICC) and compared to ELA technic's data. The field-effect mobility was decreased from 106.78 to $88.74\;cm^2$/Vs and threshold voltage also decreased from -1.8382 to -0.9529 V, when TFT process is changed from ELA technic to MICC technic. Subthreshold swing, also, increased from 0.22 to 0.32 V/dec and $I_{on/off}$ ratio decreased from $1.12{\times}10^8$ to $5.75{\times}10^7$.