• Journal of Positioning, Navigation, and Timing
• /
• 제12권3호
• /
• pp.229-236
• /
• 2023

As the importance and dependency of the positioning, navigation, and timing (PNT) information provided by the radio navigation satellite service (RNSS) increases, the vulnerability of RNSS to jamming can lead to significant risks. The signal design under the consideration of anti-jamming performance helps to provide service which is robust to jamming environment. Therefore, it is necessary to evaluate the jamming robustness performance during the design of new signals. In this paper, we introduce figures-of-merit (FoMs) that can be used for an anti-jamming performance analysis of designed signals of interest. We then calculate the FoMs, such as the quality factor (Q factor), tolerable jamming-to-signal ratio (tolerable J/S), and range to jammer (d) for legacy RNSS signals and analyze the results. Finally, based on the results of the analysis, we derive waveform design conditions to obtain good anti-jamming performance. As a result, this paper shows that the waveforms with wide bandwidth leading to good spectral efficiency provide strong anti-jamming performance.

• 월간포장계
• /
• 통권27호
• /
• pp.82-83
• /
• 1995

• 건축사
• /
• 통권606호
• /
• pp.108-109
• /
• 2019

• 건축사
• /
• 통권630호
• /
• pp.114-115
• /
• 2021

• Journal of Computational Design and Engineering
• /
• 제3권4호
• /
• pp.398-413
• /
• 2016

This work describes the design and development of a new drying system for a rollover carwash machine with the support of numerical tools. The drying system is composed of a pair of stationary vertical dryers and a moveable horizontal dryer that can adjust itself to the contour of a vehicle. After the definition of the dryers' concept, their performance was assessed individually to check their internal flow pattern and to improve their airflow distribution. These issues are expected to provide feedback on redesign and geometric optimization of the dryers. After redesign of the dryers separately, the behaviour of the complete drying system was studied on actual vehicle models, representative of the shortest and tallest dimensions that can be washed with the existing carwash machine sector. The drying efficiency of the whole system was studied by calculation of shear stress distribution on various surfaces of a given vehicle. The results allowed concluding that the overall drying performance of the design system is very good and assure adequate drying on most vehicles surfaces. The results obtained from numerical studies were then validated with experimental measurements and a good agreement was found between the two. The procedure employed in this work can be applied to support the design and analysis of other mechanical drying systems.

• 한국정밀공학회지
• /
• 제27권8호
• /
• pp.13-19
• /
• 2010

A design method of railway wheel profile with objective function of equivalent conicity considering wheel dimension constraint, two points contact problem between wheel and rail was proposed. New design method shows good results. New wheel profile generated from optimization process shows better dynamic performance compared with initial profile as the purpose of wheel profile design. And to verify the design method with testing the stability of new wheel profile, we conducted a critical speed test for new wheel profile using scale model applied scaling method of railway vehicle dynamics. The result of critical speed test show good agreement with that of numerical analysis. From the above results, it is seen that the design method with objective function of equivalent conicity is feasible and it could be applied to design new wheel profile efficiently.

• 한국정밀공학회지
• /
• 제18권3호
• /
• pp.122-130
• /
• 2001

Axiomatic Design is the useful tool for making a good design. In Axiomatic design, the independency is an important property to determine whether the design is good. Until now many designers decide the independency between FRs by their own decision. The way depending on inspiration is simple and fast, but it can not be considered as precise conclusion. Also there are not exact rule that evaluate the quantitative independency between FRs. This thesis will show the way to evaluated the quantitative independency of FRs from the comparison between FRs of more lower levels, and develop more efficient and objective tool in Axiomatic Design.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2004년도 전력전자학술대회 논문집(2)
• /
• pp.985-987
• /
• 2004

Switched Reluctance Motor(SRM) drive system is known to provide good torque characteristics and high efficiency drive. However, speed variation caused by higher torque ripple is one of main drawback. The Phase-Locked Loop (PLL) technique in conjunction with dynamic dwell angle control has good speed regulation characteristics. In this paper, appropriate advance angle control for high efficiency drive and PLL technique for accurate speed control is proposed. A TMS320F240 DSP is used to realize this drive system. Test results show that the system has good dynamic and precise speed control ability as well as high efficiency.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2003년도 봄 학술발표회 논문집
• /
• pp.451-460
• /
• 2003

In this paper, high speed fiber optic sensor weigh-in motion (WIM) system is proposed. Bragg gratings which have several advantages such as good reproducibility and good multiplicity compare to other optical fiber sensors are used for the system. Fabry-Perot filter for the signal process, which cannot be used in the high speed measurement because of the limitation in fast operation of PZT, is excluded. A new signal processing system which employs bandwidth filter is proposed and bridge type new sensor package design is also proposed. Design of the mold supporter is modified to round shape and then supporting points do not change. The data from the fiber sensors show identical and linear behavior to the axle weight. The proposed fiber optic WIM system is tested in the laboratory and experimented with actual trucks. The new concept of calibration is introduced and calculated by the experiments. The calibrated weight data show good approximations to real axial weights regardless the velocities of the truck.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.2271-2272
• /
• 2008

Recently, LDPC codes received a lot of attention in 4G. LDPC codes perform good error correction at high SNR. But LDPC codes are complex design and not good at low SNR. At low SNR, convolution codes and turbo codes show more good performance than LDPC codes. The main subject presented in this study is that parallel encoding and decoding according to SNR. The system chooses convolution codes at low SNR and chooses LDPC codes at high SNR.