Kim, Dai-Byung;Lee, Jong-Kwon;Jung, Kyong-Ja;Yoon, Yeo-Pyo;Kim, Myung-Soo
Toxicological Research
/
v.14
no.3
/
pp.329-332
/
1998
Ingredients and concentrations of organic solvents in 7 kinds of adhesive sold on the domestic market were qualitatively and quantitatively analysed. Vapor concentrations were also analysed to estimate inhalation concentratins when adhesives were abused to get high. Acetone, methyl ethyl ketone, methyl cyclopenatane, cyclohexane and toluene were identified to be used in domstic adhesives as solvents. When organic solvents of adhesives were vaporized in the vial at the room temprature for 30 mins, concentrations of organic solvents in air were in the range of 5,000~140,000ppm. Among these solvents, toluene, known to have strong hallucination effect, showed 5,000~35,000 ppm. The putative concentration of toluene in case of glue sniffing was estimated to be about 5,000ppm in consideration of glue sniffing circumstances. Toluene was found in all adhesives in this study, even adhesives which toluene was not described in label.
To develope the utilities of the chestnut bur, which is wasted after harvesting chestnut in farmhouses, the feasibilities of adhesion(urea resin) extenders of the powder for plywood were examined. These experiments were implemented on experimental scale at Forestry Research Institute(Seoul) and on a plywood mill scale at Eugon Industrial Co LTD(Inchon) for more reliable data. In this paper, it was proved that the chestnut bur powder caused to rise the glue viscosity but the chaff powder to down reversely. The most effective mixing ratio were wheat flour 5kg, chaff powder: 5kg and chestnut bur powder. 5kg per 100kg of urea resin. At this condition, the viscosity were most appropriate (1,320 2,230 cps) for glue spreading operations, and the dry shear strengthes were most adequate(10.7-13.2kg/$cm^2$), wood failure ratio 82-88%). The chestnut bur powder, can be utilized for plywood adhesion extenders without any change of present process lines in plywwod mills.
Thalamoperforating artery aneurysms are rarely reported in the literature. We report an extremely rare case of ruptured distal anterior thalamoperforating artery aneurysm which was treated by endovascular obliteration in a patient with occlusion of both the internal carotid arteries (ICAs) : A 72-year-old woman presented with severe headache and loss of consciousness. Initial level of consciousness at the time of admission was drowsy and the Glasgow Coma Scale score was 14. Brain computed tomography (CT) scan was performed which revealed intracerebral hemorrhage in right basal ganglia, subarachnoid hemorrhage, and intraventricular hemorrhage. The location of the aneurysm was identified as within the globus pallidus on CT angiogram. Conventional cerebral angiogram demonstrated occlusion of both the ICAs just distal to the fetal type of posterior communicating artery and the aneurysm was arising from right anterior thalamoperforating artery (ATPA). A microcatheter was navigated into ATPA and the ATPA proximal to aneurysm was embolized with 20% glue. Post-procedural ICA angiogram demonstrated no contrast filling of the aneurysm sac. The patient was discharged without any neurologic deficit. Endovascular treatment of ATPA aneurysm is probably a more feasible and safe treatment modality than surgical clipping because of the deep seated location of aneurysm and the possibility of brain retraction injury during surgical operation.
Proceedings of the Korean Vacuum Society Conference
/
2011.02a
/
pp.381-381
/
2011
In this study, a TiO2 colloidal sol was synthesized by sol-gel process, which was used as a "glue" agent to enhance interconnection of TiO2 particles in low temperature process for plastic dye sensitized solar cell. The crystalline phase of this TiO2 glue is pure anatase with average particles size of 5 nm, which was characterized by powder X-ray diffraction and high revolution-TEM. The viscous alcoholic paste without any organic binder was prepared from the mixture of commercial P25 powder and glue. Paste composition and sintering process parameters were optimized for high photovoltaic performance based on low temperature process. The electrochemical impedance spectroscopy and photocurrent-photovoltage transient spectroscopy were also employed to investigate the mechanism of electron transport in this binder free TiO2 film system.
Kang, Hoduck;Kang, Sang-Gu;Bae, Hanhong;Park, Kyo-Soo;Hall, Richard B.
Journal of Korean Society of Forest Science
/
v.86
no.3
/
pp.261-269
/
1997
Excised immature ovules and calli derived from the stems of cottonwood were bombarded with microprojectiles carrying plasmid DNA containing CaMV-35S promoter and ${\beta}$-glucuronidase(GUS) gene. After bombarded, the expression of GUS gene was detected by the assay of 5-bromo-4-chloro-3-indolyl-${\beta}$-gluconide(X-gluc). Transient gene expression was measured by counting the number of distinct regions of GUS activity per explant. As major parameters, the number of shots and the period of exposure to X-gluc after the bombardment were investigated for detecting GUS gene expression. In this experiment, the percents of GUS gene expression showing spots were 56.8 from immature ovules and 75.9 from micro-calli of cottonwood species. Among the treatments, two consecutive shots and 48 hour exposure produced about $25.75{\pm}2.77$(per ovule), $11.43{\pm}1.22$(per mini petridish) spots, respectively, Microprojectile particle bombardment provides a useful method to assay transient expression in both types of explants. Furthermore, our results represent that the excised ovule and/or the calli might be stably transformed by the biolistics.
KSCE Journal of Civil and Environmental Engineering Research
/
v.33
no.2
/
pp.549-557
/
2013
An flood inundation map is able to convey spatial distribution of inundation to a decision maker for flood risk management. A roughness coefficient with unclear values and a discharge obtained from the stage-discharge rating equation are key sources of uncertainty in flood inundation mapping by using a hydraulic model. Also, the uncertainty analysis needs an observation for the flood inundation, and satellite images is useful to obtain spatial distribution of flood. Accordingly, the objective of this study is to quantify uncertainty arising roughness and discharge in flood inundation mapping by using a hydraulic model and a satellite image. To perform this, flood inundations were simulated by HEC-RAS and terrain analysis, and ISODATA (Iterative Self-Organizing Data Analysis) was used to classify waterbody from Landsat 5TM imagery. The classified waterbody was used as an observation to calculate F-statistic (likelihood measure) in GLUE (Generalized Likelihood Uncertainty Estimation). The results from GLUE show that flood inundation areas are 74.59 $km^2$ for lower 5 % uncertainty bound and 151.95 $km^2$ for upper 95% uncertainty bound, respectively. The quantification of uncertainty in flood inundation mapping will play a significant role in realizing the efficient flood risk management.
The characteristics of natural resin, sap of the lacquer tree were examined as an adhesive for the ceramic conservation since it has such outstanding properties like corrosion resistance against acid and alkali, heat-resistance, waterproof, antiseptic and protection against insects. In order to utilize raw lacquer as an adhesive not under the hardening conditions of lacquer like high humidity (RH 75 to 85%) and high temperature (120 to $170^{\circ}C$), but under normal condition, isinglass and animal glue were added to raw lacquer at certain ratio. In addition, the viscosity and the drying time were measured and their possibilities of application were also investigated through measurement of tensile and adhesive strength. As a result of experiment, it was possible to dry at room temperature and RH $50{\pm}5%$ to mix with raw lacquer and glue, and the drying time of sample with animal glue was faster than that of isinglass. Furthermore, the adhesion of sample with glue was increased more than raw lacquer. It seems to be possible to use the environmental friendly traditional adhesive for the ceramic conservation and restoration, if there are studies or examinations of safety of applications on objects and weathering resistance.
Fu, Jinwei;Haeri, Hadi;Sarfarazi, Vahab;Marji, Mohammad Fatehi;Guo, Mengdi
Structural Engineering and Mechanics
/
v.81
no.2
/
pp.243-258
/
2022
In this paper, tensile behavior of joint filling has been investigated under experimental test and numerical simulation (particle flow code). Two concrete slabs containing semi cylinder hole were prepared. These slabs were attached to each other by glue and one cubic specimen with dimension of 19 cm×15 cm×6 cm was prepared. This sample placed in the universal testing machine where the direct tensile stress can be applied to this specimen by implementing a special type of load transferring device which converts the applied compressive load to that of the tensile during the test. In the present work, two different joint filling thickness i.e., 3 mm and 6 mm were prepared and tested in the laboratory to measure their direct tensile strengths. Concurrent with experimental test, numerical simulation was performed to investigate the effect of hole diameter, length of edge notch, filling thickness and filling length on the tensile behavior of joint filling. Model dimension was 19 cm×15 cm. hole diameter was change in four different values of 2.5 cm, 5 cm, 7.5 cm and 10 cm. glue lengths were different based on the hole diameter, i.e., 12.5 cm for hole diameter of 2.5 cm, 10 cm for hole diameter of 5 cm, 7.5 cm for hole diameter of 7.5 cm and 5 cm for hole diameter of 10 cm. length of edge notch were changed in three different value i.e., 10%, 30% and 50% of glue length. Filling thickness were changed in three different value of 3 mm, 6 mm and 9 mm. Tensile strengths of glue and concrete were 2.37 MPa and 6.4 MPa, respectively. The load was applied at a constant rate of 1 kg/s. Results shows that hole diameter, length of edge notch, filling thickness and filling length have important effect on the tensile behavior of joint filling. In fixed glue thinks and fixed joint length, the tensile strength was decreased by increasing the hole diameter. Comparing the results showed that the strength, failure mechanism and fracture patterns obtained numerically and experimentally were similar for both cases.
1. In order to investigate the effect of variation of assembly time on glue bond strength, and to determine the optimum range of assembly time with given glue, this experiment was made at the suggestion of the Wood Technology Laboratory, School of Forestry, Yale University. 2. For this investigation, three-ply-plywoods with 1/22 inch, birch veneer, phenolic resin, and soybean glue were made at the following variation of assembly time, that is, 1, 5, 10, 25, 35, 50, and 70 minutes, under both open and closed assembly manners, and the shear strength test at dry and wet were adoptted. 3. The shear strength and wood failure of each plywood panel constructed at the given assembly time have been illustrated in Tables 1, 2, 3 and 4. It has shown that there is a remarkable tendency, for increasing assembly time to give lower shear strength and wood failure throughout almost all cases. The effective range of assembly time of tested glues in this investigation for both open and closed assembly are summarized in the Table 7. Thus, allowable assembly time for Phenolic resin may be up to 10 minutes under open assembly and up to 50 minutes under closed assembly. For soybean glue, the permissible assembly time may be up to 5 minutes under open assembly and up to 15 minutes under closed assembly. The allowable assembly time for open assembly with the same glue is reduced by approximately one third or more than one third as compared with closed assembly time. This might mean that the closed asembly time for these glues is more practical than the open assembly.
Background : The treatment strategy for urinary spontaneous pneumothorax has progressively changed with the introduction of video-assisted thoracic surgery (VATS). Recently, we modified the strategy of primary spontaneous pneumothorax. If the patient had mild dyspnea and the lung was minimally collapsed, 2 mm thoracoscopic examination was performed. If no blob or bullae was inspected, the intrathoracic air was evacuated through the 2 mm thoracoscopic troca without closed thoracostomy, and if the blob and bullae was noted, the 10 mm thoracoscopic bullecotomy was carried out immediately and also application of fibrin glue was substituted for pleural abrasion. We compared the clinical outcomes of modified treatment strategy with conventional strategy in primary spontaneous pneumothorax. Material and Method: Patients were divided into four groups. Group I (n=21) underwent 2 mm thoracoscopic examination. Group II (n=68) underwent closed thoracostomy. Group III (n=56) underwent VATS and application of fibrin glue. Group IV (n=87) underwent VATS and pleural abrasion. The duration of chest tube drainage, the duration of hospitalization and the recurrence rate were compared between group I and group II and between group III and group IV. Result: Mean age, sex, location of pneumothorax were not different in all groups. In group I, the blob or bullae were existed in 12 patients, In remaining 9 patients, the bleb or bullae was not inspected. The mean duration of hospitalization in 9 patients were 2.4 $\pm$1.0 day and in group II were 3.9$\pm$2.1 day (p=0.014). There was 1 case of recurrence among the 9 patients in group I and 26 recurrences in group II (p=0.149). The mean duration of chest tube drainage were not difference in group III and IV (group III: 2.8$\pm$1.8 day, group IV: 3.0$\pm$2.5 day). The mean duration of hospitalization was shorter in group III than group IV (group III: 5,6$\pm$2.7 day, group IV: 1.3$\pm$3.3 day)(p=0.002). There was no recurrence in group III and 7 recurrences in group IV (p=0.043). Conclusion: Our modified treatment strategy of primary spontaneous peumothorax was effective in short hospital course and low recurrence rate.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.