• 한국산학기술학회논문지
• /
• 제14권4호
• /
• pp.2000-2005
• /
• 2013

본 논문에서는 경골잔교의 Main girder에 작용하는 설계하중을 제안하였다. 구조 안전성 검토를 위하여 범용 유한요소 프로그램인 ABAQUS를 이용하여 수치해석을 실시하였다. 경골잔교의 Main girder는 휨뿐 아니라 비틀림 거동에 영향을 받고 있음을 알 수 있으며 주요 영향 하중은 비틀림이다. 또한 선정된 Main girder 단면에 대한 응력 검토를 통해 선정된 경골잔교는 구조적으로 안전하다.

• 한국철도학회논문집
• /
• 제19권4호
• /
• pp.515-525
• /
• 2016

도시형 자기부상열차 프리텐션 거더교의 최적설계를 위해서 설계변수 분석을 수행하였다. 자기부상철도용 거더 설계 시에는 중앙부 처짐을 고려해야 하므로 이와 연관있는 콘크리트 압축강도, 거더 형고, 거더 연장및 강연선비부착 길이를 설계변수로 선정하였다. 또한, 프리텐션 거더에서 지점부의 상연응력을 제어하기 위해서 강연선 개소수 및 배치방식을 설계변수로 선정하고, 강연선비부착률을 검토하였다. 설계변수 해석결과로부터 거더 처짐량에는 거더 형고와 거더 연장이 콘크리트 압축강도와 강연선 비부착 길이보다 더 큰 영향을 미치는 것을 확인하였고, 민감도 분석을 통해 설계 가중값을 제시하였다. 지점부 상연응력 제어를 위해서 비부착 강연선배치기준을 만족하는 경우에는 상연 긴장선 또는 철근배근이 필요한 것으로 확인되었다. 따라서 향후 경제성 및 시공성 향상을 위해 자기부상철도 가이드웨이의 하중특성을 고려한 비부착강연선 기준 향상에 대한 검토가 필요하다.

• Structural Engineering and Mechanics
• /
• 제55권5호
• /
• pp.953-964
• /
• 2015

A model has been proposed that can predict the ultimate torsional strength of single-box multi-cell reinforced concrete box girder under combined loading of bending, shear and torsion. Compared with the single-cell box girder, this model takes the influence of inner webs on the distribution of shear flow into account. According to the softening truss theory and thin walled tube theory, a failure criterion is presented and a ultimate torsional strength calculating procedure is established for single-box multi-cell reinforced concrete box girder under combined actions, which considers the effect of tensile stress among the concrete cracks, Mohr stress compatibility and the softened constitutive law of concrete. In this paper the computer program is also compiled to speed up the calculation. The model has been validated by comparing the predicted and experimental members loaded under torsion combined with different ratios of bending and shear. The theoretical torsional strength was in good agreement with the experimental results.

• 콘크리트학회논문집
• /
• 제12권6호
• /
• pp.13-22
• /
• 2000

In order to resolve the problem of increasing traffic entailed by the economic development, road system is reorganization and new highways are built, and long span bridges over 40m are being constructed in environmental and aesthetic considerations. Most long span bridges that are currently being constructed are in general steel box girder and preflex girder bridges; however these types of breiges are less efficiency than PSC I-type girder bridges in terms of construction cost and maintenance. Therefore, in these study, structural efficiency of PSC I-type girders based on section parameters, concrete compressive strength and other design parameter is observed to develope new PSC I-type girder for long span bridges. As a results of analysis, most important design parameters that control the stress of the girder are found to be the top flange width and the height of girder. In this light, the relationship between the two variables is determined and cross-section details of the girder that most appropriates for the long span bridges are proposed. The use of high strength concrete appears to increase the general design span however the increase rate of the span from increasing concrete ultimate strength appears to be reduced depending on the span. Also, the optimal girder spacing is determined through the parameter studies of design span using the proposed girder.

• Steel and Composite Structures
• /
• 제11권1호
• /
• pp.21-38
• /
• 2011

This study examines the influence of curved, steel, I-girder bridge configuration on girder end reactions and cross frame member forces during seismic events. Simply-supported bridge finite element models were created and examined under seismic events mimicking what could be experienced in AASHTO Seismic Zone 2. Bridges were analyzed using practical ranges of: radius of curvature; girder and cross frame spacings; and lateral bracing configuration. Results from the study indicated that: (1) radius of curvature had the greatest influence on seismic response; (2) interior (lowest radius) girder reactions were heavily influenced by parameter variations and, in certain instances, uplift at their bearings could be a concern; (3) vertical excitation more heavily influenced bearing and cross frame seismic response; and (4) lateral bracing helped reduce seismic effects but using bracing along the entire span did not provide additional benefit over placing bracing only in bays adjacent to the supports.

• Structural Engineering and Mechanics
• /
• 제56권2호
• /
• pp.241-256
• /
• 2015

Channel girder bridges that consist of a deck slab and two side beams are good choices for railway bridges and urban rail transit bridges when the vertical clearance beneath the bridge is restricted. In this study, the behavior of simply supported channel girder bridges was theoretical studied based on the theory of elasticity. The accuracy of the theoretical solutions was verified by the finite element analysis. The global bending of the channel girder and the local bending of the deck slab are two contributors to the deformations and stresses of the channel girder. Because of the shear lag effect, the maximum deflection due to the global bending could be amplified by 1.0 to 1.2 times, and the effective width of the deck slab for determining the global bending stresses can be as small as 0.7 of the actual width depending on the width-to-span ratio of the channel girder. The maximum deflection and transversal stress due to the local bending are obtained at the girder ends. For the channel girders with open section side beams, the side beam twist has a negligible effect on the deflections and stresses of the channel girder. Simplified equations were also developed for calculating the maximum deformations and stresses.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.319-322
• /
• 2005

When a concrete structure is subjected to load, its response is both immediate and time dependent. Under sustained load, the deformation of a structure gradually increases with time and eventually may be many time greater than its instantanneous value. The gradual development of strain with time is caused by creep and shrinkage. On this study, to estimate of stress variations on time effects in partially prestressed concrete composite girder bridges, computer program applied Age-adjusted Effective Modulus Method(AEMM) in used.

• 한국강구조학회 논문집
• /
• 제12권5호통권48호
• /
• pp.475-485
• /
• 2000

본 연구에서는 시공성을 고려한 변단면을 갖는 합성형 강상자형교의 최소비용을 구하기 위한 자동화 최적설계 프로그램을 개발하였다. 강상자형교 설계에 필요한 설계 제약조건은 도로교 표준 시방서를 비롯한 각종 설계기준과 실무자의 경험을 바탕으로 정식화하였다. 최적화의 효율성을 위해 강상자형교의 특성을 고려한 제약조건 소거기법, 설계 변수 연결기법, 응력 재해석 기법을 적용하였다. 본 연구에서 개발된 프로그램은 구조해석 모듈, 최적설계모듈, 사용자의 입력 편의를 위한 전처리모듈 설계 업무자동화를 위한 후처리모듈로 구성되어 있으며, 구조해석은 신뢰성이 입증된 상업용 구조해석 프로그램인 RM-SPACEFRAME을 이용하여 격자모델에 대해 실시하도록 하였다. 또한 개발된 최적 설계 프로그램의 효율성과 실용성을 확인하기 위하여 몇 가지의 수치예제를 적용하였다. 본 연구에서 개발된 최적설계 시스템은 향후 타 형식의 교량에 최적설계 프로그램의 모형으로 활용될 수 있으리라 사료된다.

• 콘크리트학회논문집
• /
• 제26권2호
• /
• pp.109-116
• /
• 2014

압축강도 160MPa과 길이 15.4 m를 가진 초고강도 섬유보강 콘크리트 분절박스 거더의 휨거동 실험을 수행하였다. 초고강도 섬유보강 콘크리트 분절 박스에 연성거동 특성을 보강하기 위한 강섬유와 종방향철근의 조합 효과를 두종류의 강섬유 혼입률로 제작된 초고강도 분절형 박스거더의 휨거동을 비교함으로써 평가하였다. 강섬유 혼입률이 1%이고 전단철근과 상부플랜지와 복부에 종방향철근으로 보강한 초고강도 콘크리트 박스거더 BF2의 거동은 탄성응력대에서 전단철근 없이 강섬유 혼입률 2%인 초고강도 섬유보강 콘크리트 박스거더와 유사한 연성거동을 보여준다. 그러나 비선형응력대에서는 BF1의 강성이 약간 더 크고 안정적인 연성거동 형태를 보여주고 있다. 초고강도 섬유보강 콘크리트 박스거더의 분절면은 휨파괴 시까지 균열이나 슬립이 발생하지 않았다.

• Steel and Composite Structures
• /
• 제24권5호
• /
• pp.549-559
• /
• 2017

As few multi-tower single-box multi-cell cable-stayed bridges with corrugated steel webs have been built, analysis is mostly achieved by combining single-girder model, beam grillage model and solid model in support of the design. However, such analysis methods usually suffer from major limitations in terms of the engineering applications: single-girder model fails to account for spatial effect such as shear lag effect of the box girder and the relevant effective girder width and eccentric load coefficient; owing to the approximation in the principle equivalence, the plane grillage model cannot accurately capture shear stress distribution and local stress state in both top and bottom flange of composite box girder; and solid model is difficult to be practically combined with the overall calculation. The usual effective width method fails to provide a uniform and accurate "effective length" (and the codes fail to provide a unified design approach at those circumstance) considering different shear lag effects resulting from dead load, prestress and cable tension in the construction. Therefore, a novel spatial grid model has been developed to account for shear lag effect. The theoretical principle of the proposed spatial grid model has been elaborated along with the relevant illustrations of modeling parameters of composite box girder with corrugated steel webs. Then typical transverse and longitudinal shear lag coefficient distribution pattern at the side-span and mid-span key cross sections have been analyzed and summarized to provide reference for similar bridges. The effectiveness and accuracy of spatial grid analysis methods has been finally validated through a practical cable-stayed bridge.