• KSTLE International Journal
• /
• 제2권2호
• /
• pp.93-102
• /
• 2001

Ball bearings have been widely used for the spindle motor bearing in various kinds of information storage devices. Recently many researchers have been trying to replace ball bearings with fluid film bearings because of their superior NRRO(non-repeatable runout) characteristics. In this study, a numerical analysis has been conducted for the complicate bearing system composed of herringbone groove journal bearing and spiral groove thrust bearing for the spindle motor of the information storage device. At first, spindle motor bearing is modeled as journal bearing part and thrust bearing part separately, and then observed various influences of geometric parameters. Previous studies had considered only the translational motion of the journal bearing. However, this study takes the additional 2-degree of freedom rotation into consideration to attempt to describe the real motion of the spindle bearing. As a result, rotational stiffness coefficients and rotational damping coefficients are obtained. In addition, a spindle bearing system made up of four bearings is modeled and interpreted at once and coefficients of dynamic characteristics of each bearing are obtained. Finally, an eigen analysis of bearing system is made with these results. Through this analysis, it is possible to estimate an unstable condition of the system for given geometric parameters and to propose a method which is able to avoid the unstable condition by a proper adjustment of geometric parameters.

• 대한기계학회논문집B
• /
• 제31권7호
• /
• pp.581-587
• /
• 2007

At present time, LNG demand of the world is increasing and the piping line for NG transportation has been already installed in Korea. The air fm vaporizer is, however, required because of the transportation for remotely local areas. This paper numerically investigates on the heat transfer characteristics of relevant geometric variations of air-fin vaporizer which is heated by air not by sea water. This vaporizer must be designed in consideration of both efficiency and economics because air is relatively a little heat source. In this study, the pipe and the longitudinal fins are fundamental geometric considerations. Main parameters of geometry are the number, the thickness, and the length of the fins. Finally, the results of heat transfer effects are investigated with the characteristics of each parameter variation.

• 설비공학논문집
• /
• 제26권4호
• /
• pp.163-168
• /
• 2014

The plate heat exchanger has been widely used in water heating systems due to high efficiency, simple structure, and easy maintenance. However, the studies on the effects of fouling on the heat transfer performance under various operation and maintenance conditions are very limited in the open literature. The objective of this study is to investigate the effects of fouling with calcium carbonate ($CaCO_3$) on the heat transfer characteristics of the plate heat exchanger under various operating and geometric conditions. The heat transfer coefficient and pressure drop in the plate heat exchangers were measured under accelerated fouling conditions with $CaCO_3$ by varying geometric and operational parameters. The fouling resistance increased with the decrease in the flow rate, and the increase in the chevron angle and the concentration.

• 한국공작기계학회논문집
• /
• 제11권6호
• /
• pp.1-9
• /
• 2002

This study describes the geometric characteristics and the 5-axis machining method in order to make end mill cutter coming with insert tips. End mill geometry is consisted of flute part and insert tip part. Flute part modeled by using ruled surfaces with constant helix angle, and insert tip part modeled by rectangular planes containing tapped hole of specified direction in its center. In this study, the modeled insert tip part considered both of a radial rake angle and a axial rake angle, because they were important cutting conditions. In order to machining the virtual end mill defined from geometric characteristics, we programmed a special software to machining the end mill considered in this study. This software can generate NC-codes about following processes, end milling or ball end milling of flute part end milling of rectangular plane, centering of hole, drilling of hole, and tapping of hole. Ant sampled end mills were modeled and machined on 5-axis CNC machining center with two index tables. Since machined end mills were very agreeable to designed end mills, we saw that the method proposed in this study can be very useful for manufacturing of end mill body with insert tip.

• 한국조경학회지
• /
• 제22권4호
• /
• pp.119-132
• /
• 1995

This study shows the characteristics of the early phenomena of the city plan Hanyang (old city Seoul). It consists of two steps. One is to search for the constructing principles of the geometric setting. And the other is to inquire and interpret the objects of beginning and ending points of that setting. The results based on geographic analysis and historical facts are as follows: 1) The city plan Hanyang shows a certain hierarchy:the major axis and the locations of the palace and the city set up in the prority. This priority made onto lower hierarchical plans such as the site plans of palaces and city wall. For example of the significant objects are Namdaemum (South Gate of the city wall) and Kwanghwamun (South Gate of the Palace). They are on the main axis, and became the basic points of the detailed city plans. 2) The palace palace on its major axis, right-angled minor axis, and 4 grade inclination to north. The four small city wall gates located on the base of four greater gates. 3) The geometric characteristics as constructing principle found on certain hierarchical order. Thus, the natural elements as mountains, had an important effect on the arrangement of major facilities and those main constructions made on lower - hierarchical settings. 4) These facts related closely to the philosophy of Jung, Do-Jon, the initiative planer of the Hanyang.

• 대한원격탐사학회지
• /
• 제19권1호
• /
• pp.61-70
• /
• 2003

This paper proposes an autonomous approach to localize the center of fiducial marks included in aerial photographs without precise geometric information and human interactions. For this localization, we present a conceptual model based on two assumptions representing symmetric characteristics of fiducial area and fiducial mark. The model makes it possible to locate exact center of a fiducial mark by checking the symmetric characteristics of pixel value distribution around the mark. The proposed approach is composed of three steps: (a) determining the symmetric center of fiducial area, (b) finding the center of a fiducial mark with unit pixel accuracy, and finally (c) localizing the exact center up to sub-pixel accuracy. The symmetric center of the mark is calculated tv successively applying three geometric filters: simplified ${\nabla}^2$G (Laplacian of Gaussian) filter, symmetry enhancement filter, and high pass filter. By introducing a self-diagnosis function based on the self-similarity measurement, a way of rejecting unreliable cases of center calculation is proposed, as well. The experiments were done with respect to 284 samples of fiducial marks composed of RMK- and RC-style ones extracted from 51 scanned aerial photographs. It was evaluated in the visual inspection that the proposed approach had resulted the erroneous identification with respect to only one mark. Although the proposed approach is based on weak constraints, being free from the exact geometric model of the fiducial marks, experimental results showed that the proposed approach is sufficiently robust and reliable.

• 농업과학연구
• /
• 제49권4호
• /
• pp.857-869
• /
• 2022

Eggs are considered an excellent complete food because they contain many major energy sources, including protein. Eggs are one of the most widely consumed foods worldwide, and egg consumption is steadily increasing. Eggs are generally classified according to their quality and weight. Various characteristics of eggs must be considered for the design and effective utilization of equipment used for the transport, processing, packaging, and storage of eggs. In this study, egg surface area, volume, density, etc. were measured according to the grade of the egg. The values of several geometrical properties that were measured tended to increase with increasing egg grade. The smallest grade eggs had the lowest shell thickness and density. The electrical conductivity of the eggshell and its contents was measured with a self-made electrode and equipment. The egg shell showed properties similar to insulators, and as the thickness increased, the electrical conductivity tended to increase. The electrical conductivity of the egg yolk showed almost constant values under all conditions. The electrical conductivity of the egg white and mixture was particularly low at 0.1 kHz. Fouling and electrode corrosion occurred in a low frequency region due to the egg white. In this study, various geometric and electrical characteristics of eggs were measured, and based on this, factors that could serve as new indicators for egg processed production were analyzed and investigated.

• 한국전산유체공학회지
• /
• 제16권2호
• /
• pp.11-16
• /
• 2011

Numerical analyses have been carried out to analyze the three-dimensional turbulent heat transfer by impingement jet on a concave surface with variation of geometric configurations. Three-dimensional Reynolds averaged Navier-stokes equations have been calculated using the shear stress transport turbulent model. The numerical results for heat transfer rate were validated in comparison with the experimental data. The distance between jet nozzles and angle of inclined jet nozzle were selected as the geometric variables. Area-averaged Nusselt numbers on concave surface are evaluated to find the characteristics of heat transfer with the two geometric variables. The heat transfer increases as the distance between jet nozzles increases, and the inclined impinging jets show much better heat transfer performance than the vertical impinging jet.

• Computers and Concrete
• /
• 제14권6호
• /
• pp.657-674
• /
• 2014

The purpose of this paper is to present a numerical procedure to analyse reinforced concrete columns subjected to combined axial loads and bending that rigorously considers nonlinear material and nonlinear geometric characteristics. Column design and stability analysis are simultaneously regarded. A finite element method is used for calculating displacements and the material and geometric nonlinearities are taken into account using an iterative process. A computer program is developed from the proposed numerical procedure, and the efficiency of the program is verified against available experimental data. The model applies to constant rectangular cross sectional columns with symmetric reinforcement distribution.

• 설비공학논문집
• /
• 제18권1호
• /
• pp.31-37
• /
• 2006

The present study has been experimentally investigated the effect of geometric and operating parameters on the two-phase flow distribution of refrigerants in a horizontal T-junction. The operating parameters were the kind of refrigerants (R-22, R- l34a, and R-410A), saturated temperature, and the inlet mass flux and quality. The geometric parameters were the tube diameter and the tube diameter ratio. The measured data of refrigerants were compared with the values predicted using the models developed by several researchers for air/water or steani/water two-phase flow. Among the operating parameters, the inlet Quality was the most sensitive to the mass flow rate ratio. Between the geometric parameters, the tube diameter ratio was more sensitive than tube diameter.