• 한국물환경학회지
• /
• 제38권4호
• /
• pp.171-176
• /
• 2022

Recently, an autotrophic single-stage nitrogen removal (ASSNR) process based on the anaerobic ammonium oxidation (ANAMMOX) reaction has been proven as an economical ammonia treatment. It is highly evident that double-layered gel beads are a promising alternative to the natural biofilm for ASSNR because of the high mechanical strength of poly(vinyl alcohol) (PVA)/alginate structure and efficient protection of ANAMMOX bacteria from dissolved oxygen (DO) due to the thick outer layer. However, the thick outer layer results in severe mass transport limitation and consequent lowered bacterial activity. Therefore, the effects of the thickness of the outer layer on the overall reaction rate were tested in the biofilm model using AQUASIM for ammonia-oxidizing bacteria (AOB), nitrite-oxidizing bacteria (NOB) and ANAMMOX bacteria. A thickness of 0.5~1.0 mm is preferred for the maximum total nitrogen (TN) removal. In addition, a DO of 0.5 mg/L resulted in the best total nitrogen removal. A higher DO induces NOB activity and consequent lower TN removal efficiency. The optimal density of AO B and NO B density was 1~10% for a 10% ANAMMOX bacterial in the double-layered PVA/alginate gel beads. The real effects of operating parameters of the thickness of the outer layer, DO and concentrations of biomass balance should be intensively investigated in the controlled experiments in batch and continuous modes.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.1240_1241
• /
• 2009

In this paper, sol-gel-spin coated $Pb(ZrTi)O_3$ thin film with $ZrO_2$ buffer-layer and $PbTiO_3$ seed-layer was investigated for vibration MEMS energy harvester to scavenge power from ambient vibration via d33 piezoelectric mode. Piezoelectric thin film deposition techniques on insulating layer is the important key for $d_{33}$ mode of piezoelectric vibration energy harvester. $ZrO_2$ buff-layer was utilized as an insulating layer. $PbTIO_3$ seed-layer was applied as an inter-layer between PZT and $ZrO_2$ layer to improve the crystalline of PZT thin film. The fabricated PZT thin film had a remanent polarization of 5.3uC/$cm^2$ and the coercive field of 60kV/cm. The fabricated energy harvester using PZT thin film with PTO seed-layer generated 1.1uW of electrical power to $2.2M{\Omega}$ of load with $4.4V_{pvp}$ from vibration of 0.39g at 528Hz.

• 한국염색가공학회지
• /
• 제6권1호
• /
• pp.49-53
• /
• 1994

The transparent coloration of glasses has been successfully achieved by coated glass surface with squarylium dye by the sol-gel colored coating method. Treatment of sol-gel colored coating layer with HCI(g) greatly decreases the absorbance at λ$_{max}$, that increases exposure to $NH_{3}$(g) and the reversible color-colorless responce was extremely rapid.d.

• 한국표면공학회지
• /
• 제41권4호
• /
• pp.169-173
• /
• 2008

The objective of this study is to coat the $SiO_2$ layer uniformly on the ZnS:Cu phosphors by using Sol-Gel method. From results of SEM micrographs observation, XRD and XPS analysis, it could be confirmed that $SiO_2$ layer was relatively well coated on ZnS:Cu particles. $Ag_2S$ was used as a decoding chemical to analyze the dense and uniform coating performance of $SiO_2$ layer on phosphor particles. It could be concluded that phosphors synthesized from our two step replacement method showed strong blue peak comparing to other method and rather weak green peak also. Obtained particle size of phosphors were about 20m diameter. Luminescence properties of the phosphors were examined by photoluminescence spectra at the excitation wavelength of 270 nm.

• 한국전기전자재료학회논문지
• /
• 제15권1호
• /
• pp.61-66
• /
• 2002

A method for designing antireflection (AR) and antistatic (AS) coating layer by the use of conducting polymer as an electrically conductive transparent layer is proposed. The conducting AR coating is composed of four-layer with alternating high and low refractive index layer: silicon dioxide (n=1.44) and titanium dioxide (n=2.02) prepared at low temperature by sol-gel method are used as the low and high refractive index layer, respectively. The poly(3,4-ethylenedioxythiophene) which has the surface resistivity of 10$^4$Ω/$\square$ is used as a conductive layer. Optical constant of each ARAS coating layers such as refractive index and optical thickness were measured by 7he spectroscopic ellipsometer and from the measured optical constants the spectral properties such as reflectance and transmittance were simulated in the risible region. The reflectance of ARAS films on glass substrate was below 1 %R and the transmittance was higher than 95 % in the visible wavelength (400-700 nm). The measured AR spectral properties was very similar to its simulated results.

• 한국재료학회지
• /
• 제29권3호
• /
• pp.183-188
• /
• 2019

Flexible dye-sensitized solar cells using binder free $TiO_2$ paste for low temperature sintering are developed. In this paste a small amount of titanium gel is added to a paste of $TiO_2$ nanoparticle. Analysis of titanium gel paste prepared at $150^{\circ}C$ shows that it has a pure anatase phase in XRD and mesoporous structure in SEM. The formation of the titanium gel 1-2 nm coated layer is confirmed by comparing the TEM image analysis of the titanium gel paste and the pristine paste. This coating layer improves the excited electron transfer and electrical contact between particles. The J-V curves of the organic binder DSSCs fabricated at $150^{\circ}C$ shows a current density of $0.12mA/cm^2$ and an open-circuit voltage of 0.47 V, while the titanium gel DSSCs improves electrical characteristics to $5.04mA/cm^2$ and 0.74 V. As a result, the photoelectric conversion efficiency of the organic binder DSSC prepared at low temperature is as low as 0.02 %, but the titanium gel paste DSSCs has a measured effciency of 2.76 %.

• 멤브레인
• /
• 제6권4호
• /
• pp.203-212
• /
• 1996

본 연구의 목적은 수용성고분자 PVA의 한외여과 실험을 통해 한계투과량(limiting flux) 현상에 미치는 조업변수들의 효과들을 고찰하고, 또한 겔층모델(gel-layer model)의 한계성을 극복하기 위해 열전달 계수의 개념을 도입한 Amiar 모델식을 바탕으로 새로운 모델식을 제시하여 이의 적용 가능성을 살펴보았다. Polysulfone 재질의 평판막(MWCO=20,000)과 중공사형막(MWCO= 30,000)을 사용하여 막내선속도, 투과압력, 온도, PVA 농도 등의 변화에 따른 한외여과 특성을 살펴보았다. 실험결과를 통해 polysulfone 재질의 막을 통해 PVA의 한외여과 과정은 겔층형성에 따른 투과저항 메커니즘이 작용하는 것으로 나타났다. 반면에 중공사형막의 경우는 한계투과량 조건하에서 겔층모델에 의해 예측할 수 없는 upward 한계투과량 현상이 관측되었다. 점성도 보정인자(viscosity correction factor)가 포함된 새로운 모델식의 적용을 통해서 upward 한계투과량 현상을 예측하였으나 완전히 만족할만한 결과를 얻지 못했다. 그러나 이와 같은 모델식의 적용을 통해서 PVA의 한외여과 과정이 투과용액의 점성도와 매우 밀접한 관계를 가짐을 알 수 있었다.

• 약학회지
• /
• 제42권2호
• /
• pp.187-195
• /
• 1998

In order to ameliorate disadvantages of buccal ointments and mucoadhesive tablets used for the treatment of aphthosis, a thin mucoadhesive patch containing triamcinolone acetoni de was designed and evaluated for the pharmaceutical properties. The adhesive gel layer consisting of Noveon AA-1, hydroxypropylcellulose-M and ethylcellulose N 100, and the protective gel layer of ethylcellulose N 100, Eudragit RSPO and castor oil have been formulated and various properties such as viscosity of drug gel layer, thickness, in vitro adhesion time, adhesive strength, surface pH, content uniformity and drug release are tested. The mean viscosity of drug-containing gel layer was found to increase with increasing amount of Noveon OAA-1 or hydroxypropylcellulose-M. The optimum formulation showed the thickness of 171 ${\mu}$m, surface pH of 4.6, in vitro adhesion time of 8 hours and adhesive strength of 272.7g/sheet. The drug content of each patch was relatively homogeneous with the value of 273${\pm}$6.77g. Drug release study showed that compared to mucoadhesive tablet, the patch showed a faster drug release. Drug release was delayed by hydroxypropylcellulose-M, but not by ethylcellulose N 100. The patches prepared were nonirritant and the muco adhesion was better than the commercial product (AftachR) on the market. Based on these results, this mucoadhesive patch is expected to be an effective dosage form for the treatment of aphthosis.

• 한국산학기술학회논문지
• /
• 제7권5호
• /
• pp.801-804
• /
• 2006

[ $YBa_2Cu_3O_{7-{\delta}}(YBCO)$ ]계 초전도 선재용 $GdAlO_3(GAO)$ 버퍼층을 졸-겔(sol-gel) 공정에 의해 제조하였다. 전구체 용액은 Gd 질산염과 Al 질산염을 1:1 화학양론비로 하여 메탄올에 용해하여 준비하였다. 전구체 용액을 $SrTiO_3(STO)$ (100) 단결정 기판위에 스핀 코팅하고, 수분이 포함된 $N_2-5%\; H_2$ 분위기에서 $1000^{\circ}C$에서 2시간 열처리 하였다. 열처리 후 GAO 층의 표면에 대한 주사전자현미경 관찰에 의해 GAO 층이 에피택셜의 특징인 각면 형상을 갖는 것을 알 수 있었다. X-선 회절분석에 의하면 GAO 버퍼층은 c-축으로 우선 배향된 에피택셜 박막으로써 반가폭이 각각 (002)면에서 $0.29^{\circ}(out-of-plane)$, {112}지면에서 $1.10^{\circ}(in-plane)$의 우수한 배향성을 나타내었다.

• 대한안전경영과학회:학술대회논문집
• /
• 대한안전경영과학회 2003년도 추계학술대회
• /
• pp.351-357
• /
• 2003

The optimum polymer gel electrolyte composition ratio was 23 : 66 : 11 wt% of P(VdF-co-HFP) : PVP =20 : 3), (PC: EC =44 : 22) and TEABF$_4$. And the optimal thickness of polymer gel electrolyte was 50 ${\mu}{\textrm}{m}$. The electrochemical characteristics result of unit cell were 31.41 Fig of specific capacitance, and 3.21$\times$10$^{-3}$ S/cm of ion conductivity. Ion conductivity of polymer gel electrolytes decreased according to added PVP through impedance analysis, and it was higher in 7 wt%, but electrochemical characteristics of unit cell were better in 3 wt% PVP. And for excellent ion conductivity of polymer gel electrolytes, the use of a thin layer electrolyte(20 $\mu\textrm{m}$) was an effective method, but with unit cell application, the best thickness was 50 $\mu\textrm{m}$. Unit cell showed higher capacitance and more stable electrochemical performance when hot pressed between polymer gel electrolyte and electrode. This results from enhancement of the physical contact between the electrode and the polymer gel electrolyte and good accessibility of the liquid electrolyte to the electrode surface.