• Journal of Advanced Marine Engineering and Technology
• /
• v.25 no.2
• /
• pp.331-337
• /
• 2001

A numerical simulation of the temperature rise for sliding surface in dry contact is based on Jaegers formula combined with a calculated heat input. A gear tooth temperature analysis was performed. The pressure distribution has the Hertzian pressure distribution on the heat source. The heat partition factor is calculated along ling of action. A Temperature distribution of tooth surface is calculated about before and after profile modification. A Temperature of addendum and deddendum in modified gear have reduced.

• Journal of the Korean Society of Safety
• /
• v.9 no.4
• /
• pp.11-16
• /
• 1994

Acoustic emission technique is applied to the fatigue crack initiation in a carburized gear tooth. Acoustic emission test performed on carburized gear and three-point bending test equal to carburized gear hardness. The marked acoustic emission are detected at the early stage of crack initiation measured by a crack gauge and the final stage just before the tooth failure. The estimated acoustic emission energy rate are characteristic of the measured acoustic emission.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.1
• /
• pp.198-205
• /
• 1998

In this paper, the dynamic characteristics of a star type epicyclic gear train have been analyzed. Nonlinear stiffness of a gear pair were obtained considering the bending and shear deformation, Hertz contact deformation, as well as tooth fillet deformation. Nonlinear stiffness coefficients and damping coefficients around the static equilibrium position were obtained by perturbation method. The loci of the planet gears and sun gear were estimated. Tooth meshing forces and bearing reaction forces were calculated. The effects of bearing clearance and oil viscosity on the gear behavior were also analyzed.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.5
• /
• pp.96-101
• /
• 1999

This study suggests an algorithm for tooth profile generation of free from curve involute gear, a special gear of which the pitch line is a free curve instead of a circular one. For the first, a methodology for calculation of the tooth curve is developed and formulated Then the formulated algorithm, is programmed for manufacturing and verified by computer graphics. Next the calculated results as changed in to NC codes to apply to wire electric discharge machine(WEDM). Finally, the machined gear is examined in engagement with a standard involute gear.

• Tribology and Lubricants
• /
• v.5 no.2
• /
• pp.107-112
• /
• 1989

This paper deals with strength analysis of tooth and method of manufacture of external tooth profile in harmonic drive. From the calculation of load imposed on the contact teeth, moximum contact stress is investigated to design the addendum modification coefficient. New tooth profile of the external gear is generated according to the law of gearing, assuming that internal gear has involute tooth profile. External tooth profile can't be manufactured by conventional exclusive tools which have pressure angle of 20$\circ$. The method to design cutter tooth profile is presented.

• Journal of Power System Engineering
• /
• v.14 no.3
• /
• pp.64-70
• /
• 2010

In this study, designing of precise linear transferring device which can be applied to industrial machine and robot industry has been introduced. The direction of power flow and output feature are similar to current Rack-Pinion type. However, unlimited length extensity via rack modulizing, and securing high velocity transportation have been realized by applying Pin-Pinion Gear type at the operation part. The analysis has been calculated to obtain the Pin-Pinion Gear's optimized tooth profile. As a result of research, it is impossible to control precisely even overlap at the teeth of involute and sprocket. Because they have peculiar gearing structure. Therefore, modified cycloid tooth has been proposed to perform high velocity, precise control without backlash.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.2
• /
• pp.52-60
• /
• 2011

Korea is the best country for ship-building. But nowadays, the speedboat and yacht are not mostly developed yet. For the sleek lines of ship, more innovative transmission system should be obtained in the ship industry. In general, marine transmissions often use the straight shafts and the helical gears. So it makes problem that engine-room requires large space. In this case, conical gear is the best solution for this. Until now, technology of conical gear is not generalized, but it will be increased more through many applications. So, in order to get conical gear design technology by ourselves, this thesis is conducted. This paper was written to gain useful information of marine gearbox design applied conical gear through the measurement of backlash, computer analysis and tooth contact test of helical conical involute gear pairs.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.23 no.7 s.166
• /
• pp.1238-1244
• /
• 1999

Using a cylindrical worm gear under the actual condition of static loading, tooth fillet strains and transmission errors have been measured. The maximum strain occurs on the filet region of the center of the 1st mating tooth. Tooth fillet strain changes most sensitively according to the variations of the center distance and recess side eccentricity than the access side eccentricity. Even the no-backlash worm gear shows the transmission errors.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.05a
• /
• pp.65-66
• /
• 2010

To improve the gear noise quality, gear tooth grinding machine are widely used in automotive industry. While using the gear profile grinding machine to improve the gear tooth quality of the transmission, several defects such as chattering, tooth waves that cause the gear noise occasionally happened. But it is very difficult to solve that problem, because there is no one who knows the setting up the optimal grinding condition appropriately. The abnormal manufacturing conditions which make the gear noise make the engineer to spend a lot of time, effort, and money. Due to demands for solving the serious abnormal gear noise happened in the new FF 6th stage automatic transmission in the mass product stage, the vibration checking process in the worm wheel axis, work rotation and fixed axis of the grinding machine were adapted to find the root causes. As a result, gear profile wave are affected by the work rotation axis's unbalance which is caused by worm wheel feeding speed. And a primary and the secondary grinding feeding speed, cutting oil, work fixed forces are also proved as the important factors. After setting up the grinding condition reported in this paper, it was adapted successfully to the grinding machine to manufacture the new FF 6th speed automatic transmissions' output gear. The gear noise was dramatically disappeared and the process and results will offer good guides to the engineers who manufacture the gear with the grinding machine.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.7
• /
• pp.665-671
• /
• 2010

To improve the gear noise quality, gear tooth grinding machine are widely used in automotive industry. While using the gear profile grinding machine to improve the gear tooth quality of the transmission, several defects such as chattering, tooth waves that cause the gear noise occasionally happened. But it is very difficult to solve that problem, because there is no one who knows the setting up the optimal grinding condition appropriately. The abnormal manufacturing conditions which make the gear noise make the engineer to spend a lot of time, effort, and money. Due to demands for solving the serious abnormal gear noise happened in the automatic transmission in the mass product stage, the vibration checking process in the worm wheel axis, work rotation and fixed axis of the grinding machine were adapted to find the root causes. As a result, gear profile wave are affected by the work rotation axis's unbalance which is caused by worm wheel feeding speed. And a primary and the secondary grinding feeding speed, cutting oil, work fixed forces are also proved as the important factors. After setting up the grinding condition reported in this paper, it was adapted successfully to the grinding machine to manufacture the new automatic transmissions' gear. The gear noise was dramatically disappeared and the process and the results will offer good guides to the engineers who manufacture the gear with the grinding machine.