• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.141-146
• /
• 2007

A gear whine sound due to the axle system is one of the most important sound qualities in a sport utility vehicle (SUV). In the previous research about the gear whine sound, it was known that it is difficult to evaluate the gear whine sound objectively by using the only A-weighted sound pressure level because of the masking effect. In this paper, for the objective evaluation of the axle-gear whine sound, the characteristics of the axle-gear whine sound is at the first investigated based on the synthetic sound technology and the new objective evaluation method for the axle-gear whine sound is developed by using the sound metrics, which is the psychoacoustics parameters, and the artificial neural network (ANN) used for the modeling of the correlation between objective evaluation and subjective evaluation.

• 한국안전학회지
• /
• 제13권1호
• /
• pp.34-39
• /
• 1998

This paper describes a evaluation method of sound power radiated from the vibrating faces of a single stage gear box using sound radiation. The vibration caused from meshing gears is transmitted to the gear box faces through shafts and bearings. A Boundary Element Method (BEM) is developed to calculate the sound power radiated from the faces with their velocity response which is based on the Building Block Approach (BBA). Radiation efficiency as well as the sound intensity on the surface of the gear box is also calculated. Sound power of the gear box is larger in the case that bearings have offset to the wall of the gear box than that bearings are on the center of the gear box. The sound power increases with the augmentation of the offset.

• 한국소음진동공학회논문집
• /
• 제22권12호
• /
• pp.1172-1183
• /
• 2012

Aure's tonality was considered as the sound metrics for the expression of the tonality of gear whine sound in a previous research. It was failed to use the Aure's tonality as a sound metric for the tonal impression. Thus Aures's tonality, was developed for tonal impression in previous research. However, this metric did not express well the tonality of gear whine sound since the whine sound is a non-stationary signal with frequency modulation and amplitude modulation. In this study, the new method for the tonality evaluation for a non-stationary signal is presented. It is developed based on the prominence ratio, tonality impression function, and lower threshold level. It improves the accuracy and reliability of the sound quality index being used for the sound quality evaluation of the axle-gear whine sound.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.217-220
• /
• 2001

We have developed the gear sound recognition system of mechanical timer. A mechancal timer is superior in endurance to electronic timer. So it is reliable under severe operating environment. It is putting together several kind of gears. Therefore when the timer operates, it emits mechanical sound of gears. We have chosen a microphone to detect the gear sound. A microphone is more efficient and convenient than other sensors. Because it is of low price and non-contact type sensor. For ease of measurement we designed real-time processing software based on graphical user interface.

• 한국소음진동공학회논문집
• /
• 제24권8호
• /
• pp.643-650
• /
• 2014

Gear transmission system is widely applied in engineering. As the problem of contact fatigue, wear, lubrication failure etc, the condition of gear teeth contacts will be worse. The vibration and sound signals in the gear system will be affected by the some failures like scuffing, abrasive wear and spalling due to the deterioration of gear teeth surface. By studying the estimation of specific film thickness, measurement of reduction in tooth thickness, visual examination of wear mechanisms on the gear teeth and their effects on the statistical parameters of vibration and sound signals, the research obtained the satisfactory results on accessing the surface fatigue wear in a spur gear system. The paper utilizes the relationship between statistical parameters obtained from sound signals and Stribeck curve to confirm the hypothesis of dependency of surface fatigue wear, specific film thickness.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.1059-1062
• /
• 2002

In this paper, after we make high speed gear requested high precision, we got data on the sound level is Max 60,000rpm for tooth modification. We make a decision about tooth modification after predicting exactly amount of tooth interference by FEM. The purpose of this research is that modified gear is to drive under stable sound level. To accomplish its, Beam elements are used to simulate the same condition as a real gear drive by FEM. From result of simulation and experiment, if it has holes to decrease whole weight of high speed gear, it is not good effect because it has much more deformation than not.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1114-1118
• /
• 2000

Impulsive sound and vibration signals in gear are often associated with their faults. Thus these impulsive sound and vibration signals can be used as indicators in the diagnosis of gear fault. The early detection of impulsive signal due to gear fault prevents from complete failure in gear. However it is often difficult to make objective measurement of impulsive signals because of background noise signals. In order to ease the detection of impulsive signals embedded in background noise, we enhance the impulsive signals using adaptive signal processing.

• 한국공작기계학회논문집
• /
• 제12권1호
• /
• pp.72-77
• /
• 2003

The stable driving condition of high speed gear is approached by shape modifications of a gear tooth. Recently, many gear designers are using FEM for the design and the manufacture of a high precision gear. In this paper, it is aimed to drive in stable sound level through the modification of the tooth and the shape of a gear. The simulation is used to understand the effect of holes for the decrement of weight and the stress variation for the tooth modification. Beam elements used to simulate the same condition as a real gear drive by FEM. The driven gear is simulated to 60,000rpm for the tooth modification.

• 한국정밀공학회지
• /
• 제12권12호
• /
• pp.173-179
• /
• 1995

This paper descrived housing design in conception of dynamic characteristics. The vibration and noise in power train system of automobile are important on the environment matter. The vibration caused by meshing teeth of gear is transmitted to the gear box faces through shafts and bearings. Shape of housing is used different radius of curvature(R=0 to 80 mm). The velocity responese, sound power and radiation efficency on the surface of gear box are calculated. The sound power and radiation efficency are compared with different radius of curvature.

• 한국생산제조학회지
• /
• 제6권2호
• /
• pp.67-75
• /
• 1997

The noise . vibration characteristics of Hypoid gears which were made from three seperate materials(SCM, TSCM, SNCM) under the identical process were investigated for the sake of durability improvement of differential gear compatible with low level noise gear set. For this study, we developed a rig experimental equipment which can perform close noise.vibration experiment of differential gear. Consequently, we could analyze the noise.vibration characteristics of final reduction gear by materials, and also we observed changes in both metallic structure and hardness according to the materials of pinion gear. In addition to this, the correlation between the vibration of the differential gear and the interior noise of the passenger vehicles was proved by analyzing the results of rig vibration experiment and field noise test.