• 한국가스학회지
• /
• 제26권2호
• /
• pp.9-13
• /
• 2022

벨트나 체인을 이용한 감속기는 간단한 장치이긴 하지만 공간을 많이 차지하여 공간상의 제약이 있기 때문에 전동휠체어 구동부에는 부적합하다. 하지만 유성기어형태의 감속기는 동일 축에서 감속이 이루어지기 때문에 부피를 작게 할 수 있어 공간의 제약이 벨트나 체인형태의 감속기보다 덜하다. 따라서 본 연구에서는 수·전동전환이 가능한 휠체어의 구동부에 대한 연구를 통하여 유성기어형태를 이용한 감속기로 큰 추진력을 얻을 수 있는 구동부를 개발하였다. 그에 따라 감속기에 적용되는 유성기어의 치형을 Kisssoft 프로그램을 이용하여 설계를 진행하였다. 또한 기존 휠체어 바퀴에 적용 가능하도록 구동부의 설계를 진행하였고, 구동부의 수·전동 전환원리 및 작동원리에 대한 메커니즘의 최적화를 진행하였다. 연구내용을 토대로 하나의 선기어와 2개의 유성기어, 하나의 링기어를 갖는 유성기어 형태의 휠체어 감속기 구동부의 최종 설계 및 제작을 진행하였다.

• Tribology and Lubricants
• /
• 제24권6호
• /
• pp.285-290
• /
• 2008

The purpose of this paper is to present the case study of tribological failure analysis on the gear damages, oil leakage, and sealant sealing in a manual transmission of front engine and front wheel drive vehicle. The manual transmission is to change the speed range and direction of the engines depending on the driving conditions by friction driving forces with input and output gear system. The material property and surface roughness of the gears are strongly related to the gear noise and micro-vibration, oil leakage and wear, which may decrease the real contact area of the gear and the strength of the oil film thickness between the driving gear and driven one. The O-ring damage of speedometer driven gear and bad sealant sealing of oil pan may produce oil leakage through the contact surfaces, which cause the oil shortage and seizure on the sliding surfaces of the transaxle gears. In the failure case study, the proper repair working and good lubrication are very important for the long life of the transaxle without any tribological failures and oil leakage.

• 농업과학연구
• /
• 제46권3호
• /
• pp.613-627
• /
• 2019

The purpose of this study was to design a powertrain for a 78 kW AWD (all wheel drive) electric tractor by analyzing the combination of various reduction gear ratios on a commercial motor using data from actual agricultural work and driving conditions. A load measurement system was constructed to collect data using wheel torque meters, proximity sensors, and a data acquisition system. Field experiments for measuring load data were performed for two environmental driving conditions (on asphalt and soil) and four agricultural operations (plow tillage, rotary tillage, loader operation, and baler operation). The attached implements and gear stages were selected through farmer surveys. The range of the reduction ratio was determined by selecting the minimum reduction ratio needed to satisfy the torque condition required for agricultural operations and the maximum reduction gear ratio to satisfy the maximum travel speed. The minimum reduction gear ratio selected was 57 in consideration of the working load condition and the maximum reduction gear ratio selected was 62 considering the maximum running speed. In the range of the reduction gear ratio 57 - 62, the selected motor satisfied all working torque conditions. As a result, the combination of the selected motor and reduction gear ratio was applicable for satisfying the loads required during agricultural operation and driving operation.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 춘계학술대회 논문집
• /
• pp.13-19
• /
• 2007

This study is to establish design method and evaluation technology for drive system appropriate to articulated vehicles. The transmission system of articulated vehicles serves in the other condition compared with those of commercial vehicles, namely, they have to transmit high power to run and they have to make maximum use of the limited space. This paper reports the reviews and results of the design and evaluation method for driving gear unit of articulated vehicles and discusses various design items and methods about assembly and parts of driving gear unit.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.31-36
• /
• 2002

Even through the problem of misalignment is of great importance, not much work has been reported in the literature on the effect of misalignment on the vibrations of the gear-bearing systems. Therefore, the nonlinear dynamic characteristics of the gear drive system due to misalignment are investigated in this work. Transmission error for helical gear and bearing nonlinear stiffness is calculated. The equation of motion of the gear drive system is modelled using the time-varying gear meshing stiffness, bearing nonlinear stiffness, and bearing pre-load due to the housing deformation. Numerical analysis lot the gear drive system show the result of misalignment effect - sub-harmonic component, bearing pre-load effect, and another nonlinear phenomenon. And the numerical analysis are verified by the experimental result.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 1998년도 추계학술대회 논문집
• /
• pp.329-336
• /
• 1998

The characteristics of vibration and sound signals which occurs at the driving system of electric train are investigated in this study since the vibration of driving system is one of the main sources of vibration and sound in electric train. The vibration signals are changed its signal patterns during the transmission from the source to passengers due to noise or several unknown factors. To avoid the complexity of actual signals of electric train, signals from experimental apparatus of motor/gear driving system are analyzed to find the appropriate method of analysis and to characterize the signal patterns. The used methods are waterfall diagram, transfer function and modal analysis. The results shows that the vibration signals are usually originated from motor bearing and gear meshing and these signals are transmitted to bottom or bogie. Also, the sound signal is similar to the vibration of bottom or bogie, but it is not so clear to figure out the source of vibration.

• 한국소음진동공학회논문집
• /
• 제16권7호
• /
• pp.697-703
• /
• 2006

This article proposes a new technique for the reduction of vibration and noise in the geared system by adjusting the distance between gear shafts. The vibration and noise may be produced by the abnormal force applied to the tooth face. And the force may be the cause of ununiform velocity in the driven shaft. If the velocity is obtained to be uniform by adjusting the distance between shafts. the vibration and noise may be reduced to some extent. In order to review, a dynamic analysis model for the gear train used in a mill turret and a test rig are developed. The velocities in the driven shaft are calculated by dynamic simulations for the model and noises in the test rig are measured with varying of the distance between shafts. The comparison of simulation and test data shows that the distance between shafts at the most uniform velocity has the lowest level of noise.

• Tribology and Lubricants
• /
• 제17권1호
• /
• pp.16-21
• /
• 2001

The wear particles is released from the moving surfaces in gear systems of transmission and its morphology is directly related to the damage and failure to gear system from which the particles originated. It is the effective method for damage condition estimation of automobile transmission gear to observe wear debris in gear oil. We tested with new transmission and took out gear oil according to driving distance. To be applied to damage condition of gear system in transmission of automobile,4 shape parameters of wear particles in gear oil were calculated and wear volume were presumed with the image processing system.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2009년도 춘계학술대회 논문집
• /
• pp.274-279
• /
• 2009

Reduction Gear Box where from productive site uses the gear with power delivery with high mechanical efficiency of power a deceleration and as the mechanical element union product which has the velocity ratio which is various together is produced with the power occurrence motor and leads gets a high driving force is plentifully used. The above occurs from gear drive issue sound Whine, Noise and Vibration as occurring from the rim process which the gear will bite mainly is delivered with the case etc. gear drive whole which leads the axis and the bearing. The productivity falls with the going straight rate decrease which with like this problem point is caused by with rework the problem point where the cost of production rises under improving boil many kinds analyzed the plan and investigates the resultant acceleration sensor which and a frequency analysis system and was made to apply.

• 한국정밀공학회지
• /
• 제12권12호
• /
• pp.157-164
• /
• 1995

Straight belvel gear is used mainly for steering system, final reduction and differential gear in the automobile. The more high load, high velocity driving bevel gear, the more unsafe and unpleasant. In thid study, we get a kinematic equation by modelling straight bevel gear pair with simple elastic system, the dynamic characteristic analysis about this system, we got the dynamic load factor of tooth surface. Comparing the value of dynamic load factor by calculation with the measured value of Terauchi's experimental results is similar. We think it useful to analysis the vibration and the noise of straight bevel gear in operation with the analytic method of dynamic load of straight bevel gear using in this study.