• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.12
• /
• pp.106-114
• /
• 1994

The local oxidation of silicon (LOCOS) technology, which uses a silicon nitride film as an oxidation mask and a pad oxide beween the silicon nitride and the silicon substrate, has been widely used in integrated circuits for process simplicity. But, due to long brid's beak length, there are difficulties in scabilities. Many advanced isolation techniques have been wuggested for the feduction of bird's beak length. In this paper, we presented reduced bird's beak length using the polybuffered oxide and the silicon nitride as the sidewall. Also, investigating the electrical behavior of the parasitic Al-gate MOSFET on LOCOS, we proved the validity for new isolation process.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.241-244
• /
• 2012

In this paper, three types of optical receivers are designed using a $0.35-{\mu}m$ standard CMOS technology for plastic optical fiber (POF) applications. Basic common-source transimpedance amplifier (CS-TIA), common-gate TIA (CG-TIA), and regulated-cascode TIA (RGC-TIA) are optimally designed, and their transimpedance gain (TZ gain), 3-dB bandwidth, and noise characteristics are compared and analyzed. As a result of simulations, the RGC-TIA indicates better TZ gain and 3-dB bandwidth than other topologies, and CS-TIA has the best noise performance. Each optical receiver occupies area of $0.35mm^2$.

• Journal of IKEEE
• /
• v.26 no.3
• /
• pp.422-429
• /
• 2022

A light sensor chip requires a small capacity eFuse (electrical fuse) OTP (One-Time Programmable) memory IP (Intellectual Property) to trim analog circuits or set initial values of digital registers. In this paper, 128-bit eFuse OTP IP is designed using only 3.3V MV (Medium Voltage) devices without using 1.8V LV (Low-Voltage) logic devices. The eFuse OTP IP designed with 3.3V single MOS devices can reduce a total process cost of three masks which are the gate oxide mask of a 1.8V LV device and the LDD implant masks of NMOS and PMOS. And since the 1.8V voltage regulator circuit is not required, the size of the illuminance sensor chip can be reduced. In addition, in order to reduce the number of package pins of the illumination sensor chip, the VPGM voltage, which is a program voltage, is applied through the VPGM pad during wafer test, and the VDD voltage is applied through the PMOS power switching circuit after packaging, so that the number of package pins can be reduced.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.6
• /
• pp.109-118
• /
• 1998

This paper presents an ASIC implementation of video encoder which converts either digital RGB or YCbCr to S-video(Y/C) and composite video signal. The video timing signal of this encoder includes horizontal sync., vertical sync. signal and blanking, and this encoder supports field identification signal which is convenient for video editing. The encoder has been designed in the 4 stages pipeline structure to assure the stable operation of each submodule. The proposed encoder requires only 20K gates ,which is a 40% reduction in hardware compared with [13]. The designed encoder was fabricated in $0.65{\mu}m$ SOG triple metal CMOS technology. Chip size is $3.7478mm {\times} 4.4678mm$ including PAD, gate counts is 19,468 and dissipated power is 0.9W.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.11
• /
• pp.1055-1063
• /
• 2013

Low noise amplifiers(LNAs) are an integral component of RF receivers and are frequently required to operate at wide frequency bands for various wireless systems. For wideband operation, important performance metrics such as voltage gain, return loss, noise figures and linearity have been carefully investigated and characterized for the proposed LNA. An inductive shunt feedback configuration is successfully employed in the input stage of the proposed LNA which incorporates cascaded networks with a peaking inductor in the buffer stage. Design equations for obtaining low and high input matching frequencies are easily derived, leading to a relatively simple method for circuit implementation. Careful theoretical analysis explains that poles and zeros are characterized and utilized for realizing the wideband response. Linearity is significantly improved because the inductor between gate and drain decreases the third-order harmonics at the output. Fabricated in $0.18{\mu}m$ CMOS process, the chip area of this LNA is $0.202mm^2$, including pads. Measurement results illustrate that input return loss shows less than -7 dB, voltage gain greater than 8 dB, and a little high noise figure around 7~8 dB over 1.5~13 GHz. In addition, good linearity(IIP3) of 2.5 dBm is achieved at 8 GHz and 14 mA of current is consumed from a 1.8 V supply.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.7
• /
• pp.1332-1339
• /
• 2001

SoC(System on Chip) technology is widely used in the field of embedded systems by providing high flexibility for a specific application domain. An important aspect of development any new embedded system is verification which usually requires lengthy software and hardware co-design. To reduce development cost of design effort, the instruction set of microprocessor must be suitable for a high level language compiler. And FPGA prototype system could be derived and tested for design verification. In this paper, we propose a 16 bit FPGA microprocessor, which is tentatively-named EISC16, based on an EISC(Extendable Instruction Set Computer) architecture for embedded applications. The proposed EISC16 has a 16 bit fixed length instruction set which has the short length offset and small immediate operand. A 16 bit offset and immediate operand could be extended using by an extension register and an extension flag. We developed a cross C/C++ compiler and development software of the EISC16 by porting GNU on an IBM-PC and SUN workstation and compared the object code size created after compiling a C/C. standard library, concluding that EISC16 exhibits a higher code density than existing 16 microprocessors. The proposed EISC16 requires approximately 6,000 gates when designed and synthesized with RTL level VHDL at Xilinix's Virtex XCV300 FPGA. And we design a test board which consists of EISC16 ROM, RAM, LED/LCD panel, periodic timer, input key pad and RS-232C controller. 11 works normally at 7MHz Clock.