• Journal of Surface Science and Engineering
• /
• v.49 no.6
• /
• pp.580-586
• /
• 2016

Cr-Si-Al-N coating with different Si content were deposited by hybrid physical vapor deposition (PVD) method consisting of unbalanced magnetron (UBM) sputtering and arc ion plating (AIP). The deposition temperature was $300^{\circ}C$, and the gas ratio of $Ar/N_2$ were 9:1. The CrSi alloy and aluminum targets used for arc ion plating and sputtering process, respectively. Si content of the CrSi alloy targets were varied with 1 at%, 5 at%, and 10 at%. The phase analysis, composition and microstructural analysis performed using x-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) including energy dispersive spectroscopy (EDS), respectively. All of the coatings grown with textured CrN phase (200) plane. The thickness of the Cr-Si-Al-N films were measured about $2{\mu}m$. The friction coefficient and removal rate of films were measured by a ball-on-disk test under 20N load. The friction coefficient of all samples were 0.6 ~ 0.8. Among all of the samples, the removal rate of CrSiAlN (10 at% Si) film shows the lowest values, $4.827{\times}10^{-12}mm^3/Nm$. As increasing of Si contents of the CrSiAlN coatings, the hardness and elastic modulus of CrSiAlN coatings were increased. The morphology and composition of wear track of the films was examined by scanning electron microscopy (SEM) and energy dispersive spectroscopy, respectively. The surface energy of the films were obtained by measuring of contact angle of water drop. Among all of the samples, the CrSiAlN (10 at% Si) films shows the highest value of the surface energy, 41 N/m.

• Journal of the Ergonomics Society of Korea
• /
• v.30 no.1
• /
• pp.99-108
• /
• 2011

Almost all companies have paid much attention to the safety management ranging from maintenance to operation even at the stage of designing in order to prevent accidents, but fatal accidents continue to increase throughout the world. In particular, it is essential to systematically prevent such fatal accidents as fire, explosion or leakage of toxic gas at factories in order to not only protect the workers and neighbors but also prevent economic losses and environmental pollution. Though it is well known that accident probability is very low in NPP(Nuclear Power Plants), the reason why many researches are still being performed about the accidents is the results may be so severe. HRA is the main process to make preparation for possibility of human error in designing of the NPP. But those techniques have some problems and limitation as follows; the evaluation sensitivity of those techniques are out of date. And the evaluation of human error is not coupled with the design process. Additionally, the scope of the human error which has to be included in reliability assessment should be expanded. This work focuses on the coincidence of human error and mechanical failure for some important performance shaping factors to propose a method for improving safety effectively of the process industries. In order to apply in these purposes into the thesis, I found 63 critical Performance Shaping Factors of the eight dimensions throughout studies that I executed earlier. In this study, various analysis of opinion of specialists(Personal Factors, Training, Knowledge or Experience, Procedures and Documentation, Information, Communications, HMI, Workplace Design, Quality of Environment, Team Factors) and the guideline for construction of PSF were accomplished. The selected method was AHP which simplifies objective conclusions by maintaining consistency. This research focused on the implementation process of PSF to evaluate the process of PSF at each phase. As a result, we propose an evaluation model of PSF as a tool to find critical problem at each phase and improve on how to resolve the problems found at each phase. This evaluation model makes it possible to extraction of PSF succesfully by presenting the basis of assessment which will be used by enterprises to minimize the trial and error of construction process of PSF.

• Korean Journal of Materials Research
• /
• v.8 no.10
• /
• pp.961-968
• /
• 1998

In order to investigate the effects of substrate bias voltage on the formation of$ZnS-SiO_2$ protective film in phase change optical disk by R.F. magnetron sputtering method, thin dielectric film was formed on Si wafer and Corning glass by using ZnS(80mol%)-$SiO_2$(20mol%)t arget under argon gas. In this study, the Taguchi experimental method was applied in order to obtain optimum conditions with reduced number of experiments and to control numerous variables effectively. At the same time this method can assure the reproducibility of experiments. Optimum conditions for film formation obtained by above method were target RF power of 200 W. substrate RF power of 20 W, Ar pressure of 5 mTorr. sputtering time of 20 min.. respectively. The phase of specimen was determined by using XRD and TEM. The compositional analysis of specimen was performed by XPS test. In order to measure the thermal resistivity of deposited specimen, annealing test was carried out at $300^{\circ}C$ and $600^{\circ}C$. For the account of void fraction in thin film, the Bruggeman EMA(Effective Medium Approximation) method was applied using the optical data obtained by Spectroscopic Ellipsometry. According to the results of this work, the existence of strong interaction between bias voltage and sputtering time was confirmed for refractive index value. According to XRD and TEM analysis of specimen, the film structure formed in bias voltage resulted in more refined structures than that formed without bias voltage. But excess bias voltage resulted in grain growth in thin film. It was confirmed that the application of optimum bias voltage increased film density by reduction of void fraction of about 3.7%.

• Fire Science and Engineering
• /
• v.13 no.1
• /
• pp.37-47
• /
• 1999

The spreading fire of very small floating particles after they are ignited is fast and t therefore dangerous. The research on this area has been limited to experiments and global simulations which treat them as dusts or gaseous fuel with certain concentration well m mixed with air. This research attempted micro-scale analysis of ignition of those particles modeling them as liquid droplets. For the beginning, the in-line array of fuel droplets is modeled by two-dimensional, unsteady conservation equations for mass, momentum, energy and species transport in the gas phase and an unsteady energy equation in the liquid phase. They are solved numerically in a generalized non-orthogonal coordinate. The single step chemical reaction with reaction rate controlled by Arrhenius’ law is assumed to a assess chemical reaction numerically. The calculated results show the variation of temperature and the concentration profile with time during evaporation and ignition process. Surrounding oxygen starts to mix with evaporating fuel vapor from the droplet. When the ignition condition is met, the exothermic reactions of the premixed gas initiate a and burn intensely. The maximum temperature position gradually approaches the droplet surface and maximum temperature increases rapidly following the ignition. The fuel and oxygen concentration distributions have minimum points near the peak temperature position. Therefore the moment of ignition seems to have a premixed-flame aspect. After this very short transient period minimum points are observed in the oxygen and fuel d distributions and the diffusion flame is established. The distance between droplets is an important parameter. Starting from far-away apart, when the distance between droplets decreases, the ignition-delay time decreases meaning faster ignition. When they are close and after the ignition, the maximum temperature moves away from the center line of the in-line array. It means that the oxygen at the center line is consumed rapidly and further supply is blocked by the flame. The study helped the understanding of the ignition of d droplet array and opened the possibility of further research.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.4
• /
• pp.775-784
• /
• 2000

Nitrate dry deposition fluxes were directly measured using knife-leading-edge surrogate surface (KSS) covered with greased strips and a water surface sampler (WSS). The average gaseous flux ($8.3mg/m^2/day$) was much higher than the average particulate one ($3.0mg/m^2/day$). The best fit gas phase mass transfer coefficient (MTC) of $HNO_3$ was obtained by linear regression analysis between measured gaseous flux containing nitrogen compounds and measured ambient $HNO_3$ concentration. The result showed that the MTCs of $HNO_3$ were approximately two times higher than those of $SO_2$. Especially, during the ozone action day, measured gaseous fluxes containing nitrogen compounds were much higher than those ones calculated as the product of measured ambient $HNO_3$ concentration and gas phase MTC of $HNO_3$, which is calculated from MTC of $SO_2$ using Graham's diffusion law. This result indicated that other nitrogen compounds except $HNO_3$ contributed to gaseous flux containing nitrogen compounds into the water surface sampler. The theoretical calculations suggest the contributions of nitrous acid ($HNO_2$) and PAN to the gaseous dry deposition flux of nitrogen containing compounds to the WSS.

• Korean Journal of Environmental Agriculture
• /
• v.16 no.4
• /
• pp.333-340
• /
• 1997

An analytical method was developed to determine residues of haloxyfop-R and its methyl ester in soils and soybeans using gas-liquid chromatography (GLC) with electron capture detector (ECD). Soil or soybean sample was acidified and extracted with acetone. The extract was then subjected to ion-associated partition to individually separate haloxyfop-R and the neutral methyl ester. One phase containing haloxyfop-R was methylated with $BF_3$/methanol, partitioned to n-hexane and analyzed by GLC/ECD. The other phase containing the methyl ester was further purified by Florisil column chromatography prior to GLC determination. No cross contamination was found between two phases containing each of the acid and methyl ester, thus two compounds can be separately determined as the identical haloxyfop-R-methyl. Overall recoveries of haloxyfop-R from fortified samples averaged 88.2${\pm}$3.9% (n=12) and 88.3${\pm}$4.0% (n=6) for soils and soybeans respectively, and those of haloxyfop-R-methyl showed mean values of 89.2${\pm}$4.0% (n=12) and 85.6${\pm}$5.6% (n=6). Detection limits of both haloxyfop-R and its methyl esterwere 0.005㎎/㎏ and 0.01㎎/㎏ for soil and soybean samples respectively.

• Food Engineering Progress
• /
• v.14 no.3
• /
• pp.249-255
• /
• 2010

Ten commercial activated carbons (ACs) prepared from four different sources (bamboo, wood, peat, and coal) were evaluated for their adsorptive efficiency of six volatile compounds (isoamyl alcohol, hexanal, furfural, ethyl lactate, ethyl octanoate, 2-phenyl ethanol) which were dissolved in a 30% alcoholic model solution. These six volatile compounds are frequently found in alcoholic beverages and possibly contribute to physiological hangover due to their high concentrations. They are also generally regarded as off-flavor compounds at certain levels in alcoholic beverages such as whisky and vodka. Two hundred mL of 30% alcoholic solutions containing these six volatile compounds were treated with 0.2 g of ACs while stirring for 16 hr; the treated solutions were then measured for their adsorptive efficiencies (or removal efficiencies) by gas chromatographic analysis using two different sampling methods (direct liquid injection and headspace-solid phase microextraction). The adsorptive efficiencies of the ACs varied depending on the identity of the volatile compounds and the source material used for making the ACs. Ethyl octanoate, 2-phenyl ethanol, and hexanal were removed at high efficiencies (34-100%), whereas isoamyl alcohol, ethyl lactate, and furfural were removed at low efficiencies (5-13%). AC prepared from bamboo showed a high removal efficiency for isoamyl alcohol, aldehydes (hexanal and furfural), and 2-phenyl ethanol; these major fusel oils have been implicated as congeners responsible for alcohol hangover.

• Atmosphere
• /
• v.23 no.4
• /
• pp.501-511
• /
• 2013

In this study, we estimate the background concentration of black carbon (BC) mass concentration measured at Gosan Climate Observatory from January 2008 to December 2011 by applying six methods: (1) Mean and Median (2) Trimmed mean method deployed in Interagency Monitoring of Protected Visual Environments (IMPROVE) network program (hereafter, IMPROVE method), (3) Concentration-frequency distribution analysis method, (4) Advanced Global Atmospheric Gases Experiment (AGAGE) method (hereafter, AGAGE method), (5) Kaufman et al. (2001) method (hereafter, Kaufman method), and (6) Airmass sector analysis. The background concentration of BC mass concentrations is estimated to be about 400~900 ng $m^{-3}$, but each method shows a large difference. The estimated background concentration, in general, is arranged in the order of: mean > IMPROVE method > median > Kaufman method > concentration-frequency distribution analysis method > AGAGE method. The background concentration estimated by the airmass sector analysis is found to be about 550 ng $m^{-3}$ which is lower than those estimated by other methods. When we apply the same analytical period (i.e., 4-day and 6-day) to both AGAGE and Kaufman methods, the estimated background concentrations are quite similar. However, further researches on the development of statistical method for estimating background concentration for various gas-phase and particulate pollutants under different environment are needed.

• Applied Chemistry for Engineering
• /
• v.27 no.6
• /
• pp.664-668
• /
• 2016

The contamination in soil, underground water and river environment became serious due to illegal waste dumping. In this study, our research group analyzed the oil species of illegally disposed oils from J City. After pretreating the mixture of oil, water and solid phases to obtain homogeneous phase components, the physical property analysis, atom analysis, and gas chromatography were performed. From the results showing 11.8% of oxygen content, $-6^{\circ}C$ of pour point and chromatogram pattern. the contaminated oil was identified as a vegetable one. High performance liquid chromatography (HPLC) analysis was also performed in order to know what kind of vegetable oil was, and the ratio of LLO, OOL and POL was found to be high indicating that the disposed oil is majorly the used soybean oil with some vegetable oil mixtures. This study can be used for identifying contaminators for oils from the illegal waste dumping.

• Applied Biological Chemistry
• /
• v.47 no.4
• /
• pp.426-429
• /
• 2004

An easy, sensitive and rapid method for the analysis of phytol, a strong ACAT (Acyl-CoA: Cholesterol Acyltransferase) inhibitory diterpenoid, was established. The pre-treatment of sample for GC analysis of phytol includes aq. MeOH extraction, partition of the extracts between EtOAc and water, and filtration of organic phase through Supelclean LC-Si SPE tube. The GC analysis of phytol for a variety of Lactuca sativa was carried out on DB-5 capillary column with flame ionization detector (FID). The consistency in phytol contents according to each variety was not shown. Especially, Jeoktoma, as RS-2 type, showed the highest phytol content.