• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.5
• /
• pp.75-83
• /
• 2019

In order to fulfill the obligation to voluntarily reduce greenhouse gas emissions under the Paris Climate Agreement, the proportion of coal and nuclear power generation is reduced worldwide and national efforts are being made to spread renewable energy including solar power generation. Korea also intends to increase the proportion of renewable energy generation to 30~35% by 2040 by introducing laws and regulations. In addition, while the country is trying to apply solar power generation to sidewalks and roads, there is no research related to it in Korea. Therefore, as a precedent study to develop solar power generation roads, solar power generation concrete blocks applicable to sidewalks and plazas were developed and the applicability was evaluated by constructing them on the site. As a result of indoor experiment, compressive strength was measured by 25.5~35.7MPa and flexural strength was measured by 5.1~10.5MPa, which showed that all domestic standards were satisfied. However, the higher the unit cement amount, the lower the strength was measured according to the mixing of the broken fine aggregate. The absorption rate was 5.7%, which satisfied the domestic standard of 7% or less. As a result of the freeze-thawing test, the reduction rate of the compressive strength after 100 cycles was up to 6.3%. As a result of measuring the settlement amount after construction, the maximum of 2.498mm was measured and irregular settlement occurred in the overall area, which is because the resolution of the sand layer was poor during construction. Maintenance techniques of sidewalk concrete block and solar panel need to be established more efficiently through long-term operation in the further.

• Journal of Environmental Analysis, Health and Toxicology
• /
• v.21 no.4
• /
• pp.220-228
• /
• 2018

$PM_{2.5}$-bound mercury (PBM) was monitored at weekly intervals for three years (from 2014 to 2016) at an urban (Seoul) and rural site (Baengnyeong) in South Korea. The average PBM concentrations in $PM_{2.5}$ samples over the entire sampling period were $12{\pm}11pg/m^3$ and $36{\pm}34pg/m^3$ for Baengnyeong and Seoul, respectively. Seasonal differences were pronounced, with concentrations being highest in winter due to local meteorological conditions (high gas-particle coefficient due to low temperature and low mixing layer height in winter) as well as seasonal factors, such as coal combustion for heating purposes in China. In Baengnyeong, the significant positive correlation of PBM with $PM_{2.5}$, air pollutants, and heavy metals suggested that coal combustion in China might be the most important source of ambient mercury in Korea. In winter, no correlation of PBM with $PM_{2.5}$, air pollutants, and heavy metals was seen in Seoul. Furthermore, Seoul showed higher $PBM/PM_{2.5}$ and $Pb/PM_{2.5}$ ratios in winter due to the strong atmospheric oxidation-reduction reaction conditions as well as local and regional PBM sources. We conclude that immediate attention must be given to addressing PBM levels in Korea, including considering it as a key component of future air quality monitoring activities and mitigation measures.

• Clean Technology
• /
• v.27 no.1
• /
• pp.39-46
• /
• 2021

A road structure washing vehicle equipped with a 4 HP, 80 LPM ultrafine bubble generator was used to clean a tunnel wall and the surface of the surrounding structure, consisting of concrete and tiles, in a heavy traffic area around an apartment complex in the city. Ultrafine bubbles were generated by supplying air at 2 to 3 LPM and using a specially designed nozzle, whereas fine bubbles made by an impeller in a gas-liquid mixing self-priming pump were produced with an average diameter of 165.4 nm and 6.81 × 107 particles mL-1. Using a high pressure washer gun that can perform high-pressure cleaning at 150 bar and 30 LPM, ultrafine bubbles were used to wash dust adsorbed on the surface of the road structures. The experimental analysis was divided into before and after washing. The samples were analyzed by applying ISO 8502-3 to measure surface contamination of dust adsorbed on the surface. Using the transparent tape attached to the surface, the removal rate was calculated by measuring the weight of the dust, and the number of particles was calculated using the gravimetric method and the software, ImageJ. The results of the experiment showed that the number of dust particles adsorbed on the tile wall surface before and after washing were 3,063 ± 218 particles mL-1 and 20 ± 5 particles mL-1, respectively, with weights of 580 ± 82 mg and 13 ± 4 mg. Particles on the surface of the concrete structure before and after washing were 8,105 ± 1,738 particles mL-1 and 39 ± 6 particles mL-1, respectively, with weights of 1,448 ± 190 mg and 118 ± 32 mg.

• Clean Technology
• /
• v.27 no.1
• /
• pp.61-68
• /
• 2021

Selective catalytic reduction (SCR) is widely used as a method of removing nitrogen oxide in large-capacity thermal power generation systems. Uniform mixing of the injected ammonia and the inlet flue gas is very important to the performance of the denitrification reduction process in the catalyst bed. In the present study, a computational analysis technique was applied to the ammonia injection system design process of a denitrification facility. The applied model is the denitrification facility of an 800 MW class coal-fired power plant currently in operation. The flow field to be solved ranges from the inlet of the ammonia injection system to the end of the catalyst bed. The flow was analyzed in the two-dimensional domain assuming incompressible. The steady-state turbulent flow was solved with the commercial software named ANSYS-Fluent. The nozzle arrangement gap and injection flow rate in the ammonia injection system were chosen as the design parameters. A total of four (4) cases were simulated and compared. The root mean square of the NH3/NO molar ratio at the inlet of the catalyst layer was chosen as the optimization parameter and the design of the experiment was used as the base of the optimization algorithm. The case where the nozzle pitch and flow rate were adjusted at the same time was the best in terms of flow uniformity.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.27 no.1
• /
• pp.17-32
• /
• 2022

The buffer capacity of southern Korean waters in summer was quantified using data set of temperature, salinity, dissolved inorganic carbon, total alkalinity obtained from August 2020 cruise. The geographical distribution and variability of six buffer factors, which amended the existing Revelle factor, are discussed their relationship with the hydrological parameters of temperature and salinity. The calculated results of six buffer factors showed the spatial variations according to the distributions of various water masses. The buffer capacity was low in the East Sea Surface Mixed Water (ESMW) and South Sea Surface Mixed Water (SSMW) where upwelling occurred, and showed an intermediate value in the Yellow Sea Surface Water (YSSW). In addition, the buffer capacity increased in the order of high temperature Tsushima Warm Current (TWC) and Changjiang Diluted Water (CDW). This means that the Changjiang discharge water in summer strengthens the buffer capacity of the study area. The highest buffer capacity of CDW is due to its relatively higher temperature and biological productivity, and a summer stratification. Temperature showed a good positive correlation (R²=0.79) with buffer capacity in all water masses, whereas salinity exhibited a poor negative correlation (R²=0.30). High temperature strengthens buffer capacity through thermodynamic processes such as gas exchange and distribution of carbonate system species. In the case of salinity, the relationship with buffer capacity is reversed because salinity of the study area is not controlled by precipitation or evaporation but by a local freshwater input and mixing with upwelled water.

• Journal of Korea Foundry Society
• /
• v.43 no.3
• /
• pp.107-136
• /
• 2023

Natural silica sand was commonly used for sand casting of cast steel products, and chromites sand was used to suppress seizure defects due to the lack of thermal properties of silica sand. However there are disadvantages such as deterioration by repeated use, system sand mixing problem, difficulty separating and removing, increased during mold according to high density and to being waste containing chrome. Recently, industrial waste reduction and atmospheric environment improvement have been highlighted as important tasks in the casting industry. In order to solve the problems that occur when using foundry Sand and to improve the environment of casting factories, various artificial sands that can be applied instead of natural silica sand have been developed and introduced. Artificial sands can be classified into artificial sand manufactured by the electric arc atomization or gas flame atomization, artificial sand manufactured by the spray drying & sintering process, artificial sand manufactured by the sintering & crushing process and exhibit different physical properties depending on the type of raw-minerals and manufacturing method. In this study, comparative evaluation tests were conducted on the physical properties of various foundry sands, mold strength, physical durability, thermal durability, and casting test pieces. When comprehensively considering the actual amount of molding sand used according to density, the mold strength according to the shape of sand, the physical and thermal durability of foundry sand, and the heat resistance characteristics of foundry sand, 'Molten artificial sand A1' or 'Molten artificial sand B' is judged to be the most suitable spherical artificial sand for casting of heavy steel castings.

• Economic and Environmental Geology
• /
• v.34 no.4
• /
• pp.329-343
• /
• 2001

The deep environment and geochemical evolution of the Bugok geothennal waters, located in the Kyeongnam Province, was re-interpreted based on the hydrochemical and isotopic data published by Yun et al. (1998). The geothermal waters of the Bugok area is geochemically divided into three groups; Geothennal water I, II and III groups. Groups I and II are geochemically similar; high temperature (55.2-77.2$^{\circ}$C) and chemically belonging to Na-S04 types. However, pH and Eh values are a little different each other and Group II water is highly enriched in S04 compared to Group I water. Group III water, occurring from peripheral sites of the central part of the geothennal waters, shows temperature range of 29.3 to 47.0$^{\circ}$C and belongs to $Na-HCO_3-S0_4$ types. The deep environment and geochemical evolution of the Bugok geothennal waters, showing the diversity of geochemistry, can be interpreted as follows; I) Descending to great depth of meteoric waters that originated at high elevation and reacting with sediments and/or granites in depth. The $S0_4$ concentration of the waters has been increased by the dissolution of sulfate minerals in sediments. 2) During the continuous descending, the waters has met with the reduction environment, producing the $H_2S$ gas due to sulfate reduction. The waters has been heated up to 130$^{\circ}$C and the extent of water-rock reaction was increased. At this point, pH of waters are increased, S04 concentration decreased and calcite precipitated, therefore, the waters show the $Na-S0_4$ type. 3) Ascending of the geothennal waters along the flow path of fluids and mixing with less-deeply circulated waters. The $S0_4$ concentration is re-increased due to the oxidation of $H_2S$ gas and/or sulfide minerals in sediments. During continuous ascending, these geothennal waters are mixed with shallow groundwater.

• Journal of Animal Environmental Science
• /
• v.17 no.3
• /
• pp.163-170
• /
• 2011

This study was carried out to investigate greenhouse gas (GHG), $CH_4$ and $N_2O$, emission from liquid swine manure according to aeration levels in summer. To evaluate the influence of operation methods on GHG emissions, liquid swine manure were applied with different rates of aeration (store without aeration, $1m^3/ton/h$, $2.5m^3/ton/h$, and $5m^3/ton/h$). Following are the results of this study. The liquid swine manure applied no aeration, $1m^3/ton/h$, $2.5m^3/ton/h$, and $5m^3/ton/h$ aeration rates released 315.6, 13.9, 17.9 and $9.6{\mu}g/m^2/s$ of $CH_4$ and 0.173, 0.157, 0.131, and $0.241{\mu}g/m^2/s$ of $N_2O$, respectively. Liquid swine manure applied no aeration released the most amount of GHG ($6,681.4{\mu}g/m^2/s$ $CO_2$-Eq.) and followed by $5m^3/ton/h$ ($276.4{\mu}g/m^2/s$ $CO_2$-Eq.), $2.5m^3/ton/h$ ($416.0{\mu}g/m^2/s$ $CO_2$-Eq.), and $1m^3/ton/h$ ($340.8{\mu}g/m^2/s$ $CO_2$-Eq.). Our results reveal that the aerated system may reduce GHG emissions compared to no aeration. Consequently, aeration and mixing were effective at reducing GHG emissions during liquid swine manure storage.

• Journal of Animal Environmental Science
• /
• v.17 no.sup
• /
• pp.7-20
• /
• 2011

This study was conducted to analyze the mixing ratio of raw feed materials for the methane mitigation and also to identify the minimum rearing density for improving the productivity of beef calves as eco-friendly fodder. Raw materials used in this study for the formulation of feed for methane reduction were crushed corn and alfalfa along with other 21 species. In addition, to investigate the appropriate rearing density, 12 Hanwoo calves with average weight of 150 kg was selected and experiment was conducted for four months. Methane gas emission (Bo) is about 3-4 times less in TMR 4 compared to TMR 1, 2 and 3. Feed price calculated for TMR 4 ration was also affordable. In addition, all TMRs showed a normal ruminal pH. Disappearance rate was observed to be lower in TMR 4 as compared to TMR 1, 2 and 3, but methane production decreased by 24 to 37%. The result showed improved total body weight, average daily gain and feed conversion ratio in rearing low-density ($18m^2/head$), and general treatment ($9m^2/head$) compared to overcrowding treatment ($6m^2/head$). In addition, blood components (total protein, glucose, AST, ALT and GGT factors) involved in health and disease treatments and health-related nutrition metabolism are lower in the low-density and general treatment compared to the high density treatment. Postural development (development of body size) i.e., weight, height and width significantly increased in the low and general density treatment compared to high density treatment. Especially excellent improvement was observed in low-density treatment than the general treatment. Moisture content, colonic bacteria and coccidium are higher in low and high density treatments than in the general treatment. The adequacy for beef rearing density is considered to be more desirable in an area more than $6m^2/head$. In conclusion, present study suggests that possibility of methane reduction through adjusting mixed feed ration. Also, rearing density is also an important factor in the growth and development of beef calves.

• Food Science of Animal Resources
• /
• v.31 no.1
• /
• pp.100-106
• /
• 2011

The physicochemical characteristics of chicken breast were determined to identify the optimal ratio of $CO_2$ and $N_2$ to maintain chicken breast quality during cold storage for 6 d. The mixing ratios of $CO_2$ and $N_2$ were 20:80, 40:60, 60:40, and 80:20, respectively. The pH of the chicken breast packed with 80% $CO_2$ and 20% $N_2$ was lower than that of the control on day 1 (p<0.05). The lightness ($L^*$) of the breast increased with increasing $CO_2$ during storage (p<0.05), whereas no difference was found for redness ($a^*$) and yellowness ($b^*$). A lower volatile basic nitrogen level was found for chicken breasts exposed to higher $CO_2$ levels. Furthermore, lipid oxidation of the chicken breast packed with $CO_2$ decreased with increasing $CO_2$ level, and 40% $CO_2$ significantly reduced 2-thiobarbituric acid reactive substances (TBARS) values on days 1 and 6. The total number of microbes was reduced in chicken breast exposed to more than 40% $CO_2$ during storage days 3 and 6 (p<0.05); however, Escherichia coli was not affected by $CO_2$ level. Coliforms of chicken breast were reduced in the 40% $CO_2$ level on storage day 3. Moreover, tray-packed chicken breast exposed to 40% $CO_2$ did not collapse. These results suggest that 40% $CO_2$ and 60% $N_2$ were the optimal conditions for packaging chicken breasts during cold storage.